I-PRO WV-QJB502-W Base Bracket User Manual

Specifications

i-PRO white
Light gray

Precautions for installation

• In order to prevent injury, the product must be securely mounted to the wall or ceiling according to the Installation Guide of the camera.
• Make sure to remove this product if it will no longer be used.

Standard accessories

Operating Instructions (this manual) …………………… 1 pc.
The following parts are used during installation procedures.
Attachment plate ………………………………..1 pc.
Fixing screw for camera
(M4×10 mm {13/32inches}) ……………….. 4 pcs.
(of them, 1 for spare)

Fixing screw for attachment plate
(M3×10 mm {13/32 inches}) ………………. 5 pcs.
(of them, 1 for spare)
Cover …………………………………….1 pc.

Other items that are needed (not included)

• Fixing screw| Recommended screw
Minimum pull-out strength| M4/4 or 2 pcs.
196 N {44 lbf} (per 1 pc.)
---|---|---

Note:

• Select screws according to the material of the location that the camera will be mounted to.
  In this case, wood screws and nails should not be used.

• For information about the minimum pull-out strength, refer to our support website
  (https://i-pro.com/global/en/surveillance/training_support/support/technical_information

  )

Preparations

1. Remove the enclosure from the camera.
   Refer to the Installation Guide of the corresponding camera for how to remove the enclosure from the camera.

2. Check the installation direction of the conduit and the image capturing direction of the camera
   Check the connection direction of the conduit (direction of the cable access hole for conduit on this bracket) and the image capturing direction of the camera and then determine the fixing position of the attachment plate. The fixing position of the attachment plate can be changed with  steps of 90°. The following is an example of the camera direction and the fixing position of the attachment plate when connecting the conduit  from the upper side.

< When the image capturing direction is downward>

• Align the direction of the attachment plate so that the “⇧TOP” mark of the attachment plate comes to the upper side.

  ---

< When the image capturing direction is left side>

• Align the direction of the attachment plate so that the “⇧TOP” mark of the attachment plate comes to the right side.

Note:

• The connection cable is omitted in the illustration.

Parts and functions

Installations

Step1 Make a hole on the installation surface.

1. Make screw holes or anchor holes in the ceiling or wall, and also cable access hole if necessary.
   No cable access hole is needed when using conduit.A. 83.5 mm × 46 mm
   {3-9/32 inches × 1-13/16 inches}| C. 83.5 mm {3-9/32 inches}
   ---|---
   B. 82.5 mm × 47.6 mm
   {3-1/4 inches × 1-7/8 inches}| D. 83.3 mm {3-9/32 inches}

E. 63 mm {2-15/32 inches}/ 63 mm {2-15/32 inches}
Note:
• When mounting to a single-gang junction box, fix it with screws (2 pcs.) (M4: locally procured).
• The direction of the attachment plate (installation direction of the camera) can be changed with steps of 90° even after the base bracket is  fixed.

2. Remove the cap for the female thread for the conduit using a 5 mm {3/16 inches} hexagon wrench and attach the conduit.
   The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

Step2 Fix the base bracket and install the attachment plate and cover in the direction described in [2] of “Preparations”.

1. Install the base bracket on the installation surface.
   Fixing screws (4 pcs.) (M4: locally procured) Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)

2. Install the attachment plate onto the base bracket and then attach the cover to the attachment plate. The following is an example when this  bracket is installed on the wall.
   (Recommended tightening torque: 0.69 N·m {0.51 lbf·ft})

Note:

• When installing this bracket outdoors, be sure to apply waterproofing to the cable access hole and fixing screw holes.

Step3 Connect the cables to the camera.
Connect an Ethernet cable to the RJ45 network cable from the camera.
Refer to the Installation Guide of the camera for how to install the waterproof connector.

Step4 Fix the camera body to this bracket.
(Recommended tightening torque: 1.37 N·m {1.01 lbf·ft})

< When the camera is a model to be fixed with three fixing screws for camera>

< When the camera is a model to be fixed with two fixing screws for camera>

Note:

• When fixing the camera on this bracket, be careful not to pinch the cable with this bracket and damage the cable sheath.

Step5 Adjust the angle of view of the camera.
Turn on the power of the camera and adjust the angular field of view of the camera.
Refer to the Installation Guide of the corresponding camera for how to connect to a network and for how to adjust the angle of view of the camera.

Step6 Attach the enclosure.
After finishing the adjustment, attach the enclosure by following the instructions in the Installation Guide of the corresponding camera.
Refer to the Installation Guide of the corresponding camera for the recommended tightening torque to be applied when fixing the enclosure of the camera.

For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022

Ns1020-2042
Printed in China

References

• i-PRO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>