LEON VENEZIA 600 D Coffee Grinder User Manual
- June 9, 2024
- LEON VENEZIA
Table of Contents
VENEZIA 600 D Coffee Grinder
User Manual
600 D Coffee Grinder
COFFEE GRINDER 600 D – 700 D – 800 D
600 D – 700 D – 800 D are professional machines for grinding coffee and
distributing it through a manually controlled doser.
Like all appliances, it should be used with particular care to avoid injury to
personnel and damage to the appliance.
It is essential to read these instructions carefully before using the
appliance and to follow the safety recommendations.
Do not use the appliance if you have not read and understood these
instructions!
COFFEE GRINDER
Main parts (Fig. 1, Fig. 2, Fig. 3, Fig. 4)
|
---|---
- Motor housing
- Doser
- Bean hopper
- Support fork
- Dosing lever
- Grinding adjustment disc
- Bean hopper shutter
- ON-OFF (I-O) switch
- Stopping blade*
- Dose regulating knob
- Start button*/**
- Tray
- Hopper lid
- Doser lid
- Time setting knob**
- Amperometric circuit breaker (if available)
- Telescopic press and its long support fork (optional) (see also Fig. 10)
- Only on automatic models
** Only on timed models
SAFETY RECOMMENDATIONS
GENERAL INSTRUCTIONS
-
Read the following instructions carefully before using the appliance.
-
This appliance is intended for internal use only.
-
This appliance is not intended to be used in kitchens (except models with an equipotential terminal and mentioned in the Installation paragraph).
-
The maximum and minimum room temperature for correct operation of the appliance are respectively 32°C and 10°C.
-
Installation and maintenance should be carried out by qualified personnel only who are authorized for such tasks.
-
Make sure that the mains voltage is as indicated on the rating label of the appliance and that the electrical system is grounded and equipped with a switch.
-
Plug the power cable into a socket protected by a suitably rated circuit breaker (MCB) or fuses.
Do not use an adaptor plug. -
Install the appliance in a DRY, PROTECTED place, far from water sprays and jets, heat sources, open flames and inflammable substances.
-
Place the appliance on a flat, horizontal, stable surface where it cannot tip over. The highest resting surface (bean hopper) must be at a height of not less than 1,5 m.
-
This appliance is intended for professional use, and should therefore be used by experienced personnel only who are trained for this purpose. This appliance is NOT intended for industrial food processing in mass production.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental abilities, or without experience and knowledge, unless they have been instructed in the use of the appliance and are under the supervision of a person who is responsible for their safety.
CHILDREN SHOULD BE SUPERVISED SO AS TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE. -
Never use this appliance for purposes other than grinding coffee beans and dosing portions of ground coffee. Any other use is dangerous.
Do not use the doser for dosing foodstuffs other than ground coffee. -
Always work under safe conditions: do not use the appliance with wet hands or feet. Do not use outdoors.
-
Keep the original package for possible future use. It is the most suitable protection against damage during transport.
-
In case of fire use CO2 extinguishers. Do not use water or powder extinguishers.
-
Never place the appliance in water!
-
Do not disassemble the appliance or attempt to perform any repairs inside it.
-
Always unplug the appliance before performing any maintenance or cleaning and when it is not in use.
-
Never pull the appliance by the cord to move it. Never unplug it by pulling the cord or touching it with wet hands.
If the power cable is damaged it must be replaced by the manufacturer or by the technical assistance service, or at any rate by a person with similar qualifications, so as to prevent all risks. -
WARNING: Never place any utensils, metal or other hard materials, in the doser and in the bean hopper. This is dangerous and could cause damage.
-
Do not use the appliance if it is damaged or has loose parts. Immediately contact an authorized Service Center.
-
Noise: the appliance does not exceed 70 dB.
The appliance complies with European regulation CE 1935/2004 and subsequent
updates.
Note: Due to statistical tests on the product in the factory, some coffee
grounds may be found in the appliance.
SAVE THESE INSTRUCTIONS!
To consult these instructions on-line, visit the site
www.ceado.com
The EC declaration of conformity for this appliance is available in the
Products section of our website www.ceado.com.
INSTALLATION
Comply with the safety recommendations indicated above and hereafter when
installing the appliance.
For the installation of the appliance, qualified personnel must be present who
are able to check the fineness of the grind.
-
Make sure that the mains voltage is as indicated on the rating label of the appliance and that the electrical system is grounded and equipped with a switch.
-
Install the appliance in a DRY, PROTECTED place, far from water sprays and jets, heat sources, open flames and inflammable substances.
Place the appliance on a flat, horizontal, stable surface where it cannot tip over. -
Put the tray under the doser to keep the work area as clean as possible.
Before connecting the plug to the power socket, make sure that the ON-OFF switch (8 Fig. 2) is in position “0” (OFF). -
Plug the power cable into a socket protected by a suitably rated circuit breaker (MCB) or fuses. Do not use an adaptor plug.
-
Stretch the power cable out to full length. Do not let it pass over sharp edges or hot surfaces. Do not let oil spill on it. Do not let the power cable hang loose from the counter on which the appliance stands.
-
Make sure that the bean hopper is correctly positioned and that its shutter (7 Fig. 4) is completely open (to the last click).
PREPARATION AND USE
Before first use: rinse all of the parts that will have contact with food
in running water i.e.: bean hopper, lid, shutter, doser, tray.
SWITCHING ON
1 Fill the hopper with coffee beans and close the lid.
Be sure to keep the lid of the doser unit closed during operation of the
appliance.
2 Turn the ON-OFF switch to position “1”.
Manual model
The appliance will start working and must be stopped by the operator by means
of the ON-OFF switch once the desired amount of coffee has been obtained.
Automatic model
3 Press the start button (11 Fig. 3). The appliance will start working,
grinding a sufficient amount of beans to fill the doser up to its maximum
level which considers a capacity of about 300 g (200 g for model 600 D) of
ground coffee; once this has been reached, a switch device stops the motor.
Further coffee grinding will resume automatically after six doses of ground
coffee have been extracted.
Timed model
3 Set the desired operating time (5-60 seconds) using the setting knob
(15 Fig. 2) and press the start button (11 Fig. 3). The appliance will begin
to work and will stop automatically after the set time.
REGULATING GRINDING
When it leaves the factory the machine has a standard setting, but it may be
necessary to adjust grinding further due to various external factors such as
the type of mixture used, the humidity, temperature, or the particular
distribution requirements of the espresso coffee machine.
The degree of grinding may be further corrected by shifting the grinding
adjustment disc (6 Fig. 1) at the base of the hopper (see Fig. 5).
- To obtain a finer grind, move the grinding adjustment disc in a counter-clockwise direction.
- To obtain a coarser grind, move the grinding adjustment disc in a clockwise direction.
Always take care to move the disc with the motor turning and empty (without
coffee between the burrs).
NOTE! It is recommended to grind small amounts of coffee, letting the
burrs empty with every regulating attempt, by opening and closing the shutter
(7 Fig. 4) each time.
REGULATING DOSING
When it leaves the factory the machine is regulated at about 7 grams, but it
is possible to turn the dose regulating knob (10 Fig. 2) to adjust this amount
between about 6.5 grams and 10 grams (see Fig. 6).
Each complete turn of the knob corresponds to about 0.5 grams of ground
coffee: turn it clockwise to decrease the dose, turn it counter-clockwise to
increase the dose.
TAKING OUT THE COFFEE
Rest the filter-holder of the coffee machine on the support fork and pull the
doser lever all the way once or twice to extract one or two doses of ground
coffee.
The lever has a strong return spring so there is no need to reposition it
after every dose.
To distribute the ground coffee evenly in the filter use a press holding it
parallel to the filter and pressing down the coffee as preferred.
WARNINGS AND SUGGESTIONS
In the automatic model, inside the doser there is a stopping blade (9 Fig. 2)
connected to a switch which, when raised by the newly ground coffee, cuts out
the motor.
Never operate the blade by hand as this would risk filling the doser to
excess or damaging it.
Never operate without hopper and lid in place.
Make sure that shutter is completely open (to the last click) (see Fig.
7).
Do
not let the grinder-doser run long without coffee beans in the hopper; if this
were to happen it would cause tripping of the motor thermal overload
protection. In that case it is necessary to wait until the overload protection
is reset before starting to grind coffee again.
For this reason, never leave the pack of coffee beans sitting in the hopper as
this prevents you seeing how many coffee beans are left.
When the grinder-doser is not to be used during the time when the business is
closed, it should always be switched off with the main switch.
Put only coffee beans in the hopper, not ready-ground coffee or other
substances.
CLEANING
It is important to keep the appliance clean and in good working order to
ensure optimum quality of the products and long life of the appliance.
Cleaning of the appliance must be carried out by persons with knowledge and
practical experience of the appliance.
At the end of each working day, clean the outer surfaces dirty with coffee (
motor housing, tray, doser etc.). Clean the appliance completely at least once
a week.
Always disconnect the plug of the appliance from the power socket before
cleaning it.
Clean the motor housing and the tray with a cloth dampened with water or
alcohol.
Wipe with a dry cloth.
Never put the appliance under running water and never immerse in water.
Once the hopper has been removed it can be washed with lukewarm water and
neutral soap, then rinse it and dry well.
Cleaning the doser unit requires great care because inside it there is an
electromagnetically device which could get damaged.
– Use a brush or a paintbrush (Fig. 8) to clean the most hidden areas inside
the unit and a dry cloth for the other surfaces.
MAINTENANCE
Maintenance must be carried out exclusively by qualified technical
personnel.
Care for the mechanical and electrical parts of the appliance is indispensable
in order to guarantee their safety and efficiency. If any parts need replaced,
authentic spare parts must always be used.
ASSEMBLY OF THE TELESCOPIC PRESS (OPTIONAL) AND OF ITS LONG SUPPORT FORK
Before performing any assembly operations, unplug the appliance.
To assembly the telescopic press (optional) and its long support fork, proceed
as follows:
- Remove the logo sticker from the doser (1, Fig. 9) and remove the support fork, undoing the retaining screws (2, Fig. 9). Keep these screws in a safe place.
- Choose the suitable press diameter (53, 54,5 or 57,5 mm) for the filter-holder of your coffee machine and fix it to the rod of the telescopic press (1, Fig. 10).
- Position the long support fork supplied with the telescopic press and fasten it using the same retaining screws of the short fork removed previously (2, Fig. 10).
- Position the telescopic press and fasten it with the screws provided (3, Fig. 10).
- Correctly tighten the retaining screws of both the telescopic press (1, Fig. 11) and the new fork (2, Fig. 11).
Return the appliance to the working position (Fig. 12).
TROUBLESHOOTING
(See Table on the next page)
In case of any malfunction, defect of the appliance or if you suspect any
breakage after a fall, unplug the appliance immediately.
If you are unable to solve the problem referring to the table below, contact
an Authorized Service Centre.
Only qualified experts should repair the appliance.
We are not liable for any damage caused by repairs not made correctly and/or
by unauthorized personnel. In these cases the warranty does not apply.
| Problem | Solution |
|---|---|
| The appliance does not turn on. | • Make sure it is plugged in. |
• Make sure the safety circuit breaker is closed.
• Check that the main switch of the appliance is ON.
• If the problem occurs itself after a long period of intensive use, the motor
could be in thermal protection lock! Wait at least 20 minutes and try again.
The waiting time can be reduced by putting the appliance in a cool place.
• If the problem occurs after an overload, the circuit breaker on the motor
may have been tripped! Push the circuit breaker button (16 Fig. 3) under the
motor housing of the appliance (not standard equipment on all models).
• Automatic model: Check that the doser is not at maximum capacity. If it is,
move the doser lever to extract at least six doses and check that it starts
operating after having removed a certain amount of ground coffee.
• Automatic model: Check that the stopping blade is free to move.
The coarseness of the grind is not uniform.| • Try grinding very coarsely for
a few seconds, then return to the correct setting.
• Call the Technical Assistance Service to check and change the burrs.
The coffee is not coming out of the doser correctly.| • Disconnect the plug
and check for the presence of foreign bodies in the doser.
• Check that the hole where the coffee comes out of the doser is free.
The motor gets blocked.| • If the motor gets blocked due to incorrect
regulation of grinding or to the presence of a foreign body in the burrs, try
increasing to the coarsest grain size by turning the grinding adjustment disc
clockwise (6 Fig. 1).
If this is not enough, switch off the appliance, disconnect the plug from the
socket and consult technically qualified personnel.
Automatic model
The coffee overflows from the dosing unit.| • Check that the stopping blade (9
Fig. 2) is free to move.
• If the problem persists, call the Technical Assistance Service.
DISPOSAL
Correct disposal of this product (waste electrical and electronic
equipment)
(Applicable in the European Union and other countries with separate collection
systems in conformity with European Directive 2012/19/EU and subsequent
updates)
This product has been made from high-quality parts and materials, which can be
re-used and recycled.
Therefore, do not throw the product away with normal household waste at the
end of its working life. Take it to a collection point for recycling
electrical and electronic devices. This is indicated by this symbol on the
product and in the operating manual.
Please contact your local government office for information about the exact
location of the closer collection point.
WARRANTY
This product is guaranteed against faulty materials and workmanship.
The warranty period may vary according to local laws or commercial uses of the
country where the product is marketed. Therefore, please contact the retailer
from whom the product was purchased.
During the warranty period, this product can either be repaired or replaced,
at the manufacturer’s discretion, at no additional cost only if it has been
used according to the instructions in this use and maintenance manual.
If the products needs maintenance or repairs during the warranty period,
contact your retailer for shipping instructions. The product should be shipped
in its original package or other suitable packing.
The warranty does not apply in case of neglect, misuse, abuse or unauthorized
repairs. This warranty does not apply to parts subject to deterioration
through normal use such as wear to the burrs.
The warranty is limited to the costs of repair or replacement of the product
or its defective parts, or an amount equivalent to the price paid for its
purchase. No additional requests of damages will be available to the
purchaser.
The manufacturer will not accept any liability and the warranty will be
invalidated if there is a failure to follow these instructions and the
technical and/or safety standards in the country where the appliance is to be
used.
In any case these instructions cannot cover every possible event and the user
is recommended to use the appliance responsibly.
THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY ALTERATIONS TO THE
APPLIANCE WITHOUT NOTICE
Ceado S.r.l.
Tel.: (00-39) 041 50 30 767
Fax: (00-39) 041 50 38 413
E-mail: info@ceado.com
www.ceado.com
Cod. 80446 – 01/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>