ELGENS Wide Temperature TDM Series P-CAP Touch LCD Monitor User Manual

ELGENS Wide Temperature TDM Series P-CAP Touch LCD Monitor User Manual

Warning!

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in whichcase the user at his own expense will be required to take whatever measures may be required to correct the interference.

Electric Shock Hazard – Do not operate the machine with its back cover removed. There are dangerous high voltages inside

Disclaimer

This information in this document is subject to change without notice. In no event shall ELGENS Co., Ltd. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials

Packing List

Accessories (as ticked) included in this package are:

• Panel Mounting Kits
• 3 Pin Male Terminal Block
• Optional Adapter
• Other.___(please specify)

Safety Precautions

Follow the messages below to avoid your systems from damage:

• Avoid your system from static electricity on all occasions.
• Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use.
• Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system

ELGENS WEEE, ROHS and REACH Compliance Statement

When it comes to product design, the engineering team at ELGENS strives for energy efficiency and environmental friendliness–not only because it lowers monthly power costs for our customers, but also to ensure minimal energy consumption for a greener tomorrow.

Though our products (no including customer consigned materials) are not officially certified, they are in fact compliant with WEEE, RoHS and REACH standards. This means we take care to properly recycle all unused material and end-of-life products, as well as minimize the use of potentially hazardous substances.

It is not required by law that certain fixed industrial plant equipment and tools entirely omit the use of lead, mercury, cadmium, and hexavalent chromium and flame retardants such as polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). However, ELGENS assumes the responsibility to restrict the inclusion of these resources in all products, meeting the requirements of RoHS and WEEE standards.

ELGENS., Co Ltd 戎克東方科技股份有限公司
Chief Executive Officer 執行長

Santiago Li 李金柱
Date：2017 /9 /21

General Descriptions

Datasheet

 | Title| 10.1”~24” Touch monitor with IP65 front bezel, Auto Light sensor(Option), DP/VGA/HDMI, Panel Mounting kits , DC 12V input by 3-pin terminal block
---|---|---
 | Feature|

• IP65 Compliant Front Bezel
• -40 ~ 80 °C Wide Temperature
• DP / VGA / HDMI Input Port
• Panel Mounting Kits
• IEC 60945 Compliance
• Auto Light Sensor (Option)
• 1000 / 1600nits High Brightness Backlight (Option)
• Optical Bonding (Option)
• AR/AG (By Request)

 | Specification
 | Touch Screen| P-cap by USB interface (self-capacitance function include, Supports Win 10, 8, 7, XP / Linux / Android OS)
 | Power Input| 3-Pin Power Input Terminal Block

DC 12V Power Input, Optional DC9~36V Wide Voltage Power Input Fuse / Input reverse / Over current / Output short circuit protection

 | Mounting|

1. VESA Mount 75 x 75 / 100 x 100 , M4 Screw Hole
2. Panel Mounting

 | Vibration| 1.5 Grms @10~500Hz, IEC-60068-2-64
 | Shock| Half-sine, 3G @ 11ms, IEC-60068-2-27
 | Operating Temp| -40 ~ 80 °C，IEC-60068-2-1/2/14
 | Humidity| 10~90% @40 °C, non-condensing
Ordering Code|
Model Number| Description|
TDM-P101WT

TDM-P104ST

TDM-P121ST

TDM-P150ST

| 10.1″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

10.4″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

12.1″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter

15.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter

|
TDM-P156WT

TDM-P170ST

TDM-P173WT

| 15.6″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter

17.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter

17.3″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter

|
TDM-P185WT

TDM-P190ST

TDM-P215WT

TDM-P240WT

| 18.5″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

19.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

21.5″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

24.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin

terminal block DC 12V adapter

|

General instructions

1. Support Vertical refresh rate up to 75Hz for VGA~SXGA+(1400×1050) and 60Hz for higher resolution of VESA Standard Timing.
2. Support VGA analog standard input (15-pin D-Sub connectors).
3. Automatic detection of separate synchronize and composite synchronizes of VGA.
4. Support Display Port input (DP)
5. Support High-Definition Multimedia Interface (HDMI) input .
6. RoHS compliant .
7. Support Timing Table O
   Mode| Resolution| H Freq.(KHz)| V Freq.(Hz)
   ---|---|---|---
   1| 640350@70| 31.469| 70.087
   2| 640480@60| 31.469| 59.940
   3| 640480@72| 37.861| 72.809
   4| 640480@75| 37.500| 75.000
   5| 720400@70| 31.469| 70.087
   6| 800600@56| 35.156| 56.250
   7| 800600@60| 37.879| 60.317
   8| 800600@72| 48.077| 72.188
   9| 800600@75| 46.875| 75.00
   10| 1024768@60| 48.363| 60.004
   11| 1024768@70| 56.476| 70.069
   12| 1024768@72| 58.038| 71.918
   13| 1024768@75| 60.023| 75.029
   14| 128070@50| 36.91| 49.82
   15| 1280720@60| 44.62| 59.81
   16| 12801024@60| 63.980| 60.000
   17| 12801024@70| 74.882| 69.853
   18| 12801024@75| 79.976| 75.025
   19| 1360768@60| 47.72| 59.799
   20| 1440900@60| 55.935| 59.887
   21| 16801050@60| 65.3| 60
   22| 19201080@50| 56.25| 50.00
   23| 1920*1080@60| 66.6| 60

I/O Connect

I/O Connect

Block Diagram

OSD Setting

Power on LED : Off /Orange , On/Green
On/Off : Power On/Off Monitor
Menu/Enter : Open OSD , Enter , Save
Increase : Select item , Increase value
Decrease : Select item , Decrease value

OSD MAP

OSD Operation

How to reconfigure

1. Press the “MENU/Enter” button to activate the OSD menu.
2. Press the “+” / ”–“ button to navigate through the functions. Select the highlight and desired function and press the “MENU/Enter” button to activate it. If the function selected has a sub-menu, also press the “+” / ”–“ button to navigate through the sub-menu functions and select the highlight and desired sub-menu function and press the “MENU/Enter” button to activate it.
3. Press the “+” / ”–“ button to change the settings of the selected function.
4. To save the OSD menu, press the “MENU/Enter” button and press the Auto/Exit until OSD menu disappears.
5. Repeat steps 1-3 to adjust other settings.

OSD function introduction

A. Color
Set a desired color setting from this menu.

• Contrast : the adjusting range is from 0 to 100.
  

• Brightness : the adjusting range is from 0 to 100.
  

• Color Adjust :
  Red: the adjusting range is from 0 to 100.
  
  Green: the adjusting range is from 0 to 100.
  
  Blue: the adjusting range is from 0 to 100.
  

• Color Temp : contains 4 modes including 9300K, 6500K, 5800K and user

• Auto Color : Automatically adjusts the image to its optimized position, clock, and phase. (Only run on D-Sub input Mode)
  

B. Image Setting (Only run on D-Sub input Mode)
Set the image related setting from this menu.

• Clock : the adjusting range is from 0 to 100

• Phase : the adjusting range is from 0 to 100

• Sharpness : the adjusting range is from 0 to 4
  

• H.Position : the adjusting range is from 0 to 100
  

• V.Position : the adjusting range is from 0 to 100
  

C. OSD Menu
Adjusts the OSD location and language

• OSD H.Pos.: Adjusts the horizontal position (H-Position) of the OSD from 0 to 100.
  

• OSD V.Pos.: Adjusts the vertical position(V-Position) of the OSD from 0 to 100
  

• OSD Timer: Adjusts the OSD timeout from 5 to 60 seconds.
  

• Language: There are 7 languages for your selection, including English, French, Deutsch, Espanol Traditional Chinese, Simplified Chinese, Japanese
  

D. Signal Source:
In this function, you can select your desired input source

E. Signal Source:
In this function, you can reset all setting to default value

Panel Mounting Installation

Panel Mounting Kits Information

• a. Item 1 : Monunting Kits
• b. Item 2 : Panel Mount PPC

5mm Panel Monunt Panel PC

• Customers can fix Panel PC with their fixture by M3 screws.
• VESA mount holes are also available for mounting from back side
  

Preparation

• a. Item 1 : Screwdriver
• b. Item 2 : Cut out Area
  

Installation Steps

Documents / Resources

| ELGENS Wide Temperature TDM Series P-CAP Touch LCD Monitor [pdf] User Manual
Wide Temperature TDM Series P-CAP Touch LCD Monitor, Wide Temperature, TDM Series P-CAP, Touch LCD Monitor, LCD Monitor, Monitor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>