MiTek 715005354 BRP ATV Sound System Owner’s Manual

715005354 BRP ATV Sound System
Owner’s Manual

FUNCTIONAL

1.1 USER INTERFACE

• Same as the BRP Sea-doo Orca F and Orca L user interface (BT dongle). Also includes Audio line-in and line-out features on the amplifier.
• System to mute BT signal if Aux in use used
  • Loss of volume, back and forward controls will not work when in Aux in mode
• Ergonomic and safety
  • Controls are accessible while driving the vehicle
  • Controls positions are readable while driving
  • No possible entrapment of clothing or body part
  • No interference with driving maneuvers or visibility

1.2 MECHANICAL REQUIREMENTS

• All gasket and seals to be closed cell Poronfoam type
• Tweeters to IP67 rated
  • Potted with silicone glue on back side
  • Must withstand high press washing IP69K (with grill)
• No sharp edges where contact may occur while riding
• Injected plastic parts information in raised lettering:
  • FABRIQUE AU / MADE IN (XXX)SUPPLIER PART NUMBER
  • SAE PLASTIC CODE
  • CALENDAR (YEAR, MONTH)
  • CAVITY NUMBER (IF APPLICABLE)

1.2.1 Enclosures
Mitek will provide the 3D and 2D CAD for the sound system enclosures designed by BRP. The enclosures will havover-molded threaded inserts that must resist between 8 Nm and 12 Nm of torque and 250 N pull-out force.

• LH enclosure to include over molded aluminum ring for BT remote mounting
• Weep hole for condensation and water at lowest point of enclosure while installed on the machine
• M4 threaded brass inserts for amplifier and speaker (2 places for each component)
• The sound system will be installed on the front fender of the vehicle which will use M6 threaded screws. Fastener locations and qty highlighted in blue

LH enclosure

RH enclosure

1.3 ELECTRICAL
1.3.1 Maximum Input Current

• 10 Amps

1.3.1.1 Amplifier

• Amplifier to be Class D topology
• Amplifier to be DSP 50W x 2
• Amplifier to not have noticeable turn-on/off pop

1.3.2 Wireless Bluetooth

• Bluetooth Version 4.1

1.4 WIRE HARNESSES AND CONNECTIONS

• For all wire harnesses
  • Wire Type to be TWP
  • 1” rubber grommets to be used for 5mm thick material
  • 105C pvc tubing with adhesive lined heat shrink tube sealing the ends of the PVC tube to the wires.
  • Glue to be used between wires to keep out water
  • All external connectors to be sealed
  • Use dielectric grease on all internal and external connections
  • Apply connector glue to all connectors on PCB
  • Apply glue between grommet and harness for maximum sealing
• For speaker connectors
  • Solder wires directly to speaker followed by glue
• Amp connections
  • Use dielectric grease on all connectors
  • Add connector glue to all connectors
  • Secure harness to amplifier via 2x zip ties

NOTE
This device complies with Part 15 of the FCC Rules [and contains license- exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s)].
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAN ICES-003 (B) / NMB-003 (B)
Radiation Exposure Statement
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Revision 1.0 715005354
OWNER’S MANUAL

Documents / Resources

| MiTek 715005354 BRP ATV Sound System [pdf] Owner's Manual
715005354, 2AAOY-715005354, 2AAOY715005354, 715005354 BRP ATV Sound System, 715005354, BRP ATV Sound System, ATV Sound System, Sound System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>