skn MD03 Pore Purifer Advanced Microdermabrasion Tool Instruction Manual
- June 9, 2024
- skn
Table of Contents
pore purifer advanced™
microdermabrasion tool
DEEPCLEAN +
EXFOLIATE
INSTRUCTION GUIDE
**ALL MD03 MODELS
**
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS BEFORE USING SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL
DANGER – Any appliance is electrically live, even when the switch is off.
WARNING – To reduce the risk of burns, electrocution, fire, injury or death to persons:
- Always unplug appliance from electrical outlet immediately after using (except when charging tool). Do not allow to be used as a toy.
- Do not place or store appliance where it could fall or be pulled into a tub or sink.
- Do not use appliance while bathing or in the shower.
- Do not place appliance in or drop into water or other liquids.
- If appliance has fallen into water, do not reach for it. Unplug immediately.
- Unplug this appliance before cleaning.
- Do not use device if it is not working properly or if it has been dropped, damaged, or dropped into water.
- Do not place or store the charging cable where it can fall or be pulled into a tub or sink.
- Do not immerse charging cable in water or any other liquids.
- If charging cable falls into water or another liquid, unplug immediately and discontinue use.
- Not for use by children.
- Do not pull, twist or wrap the cord around the appliance.
- Never drop or insert any object into any opening on the appliance.
- THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
- Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before cleaning and servicing.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
CAUTION –
- Dry location use only. Do not expose to liquids, vapor, or rain.
- Ensure jack is plugged into the tool before plugging the USB cable into the outlet.
- Do not operate appliance with a damaged housing oruse charging cord that has been damaged.
- Always unplug the unit before cleaning or when not in use.
- Be sure voltage is correct before plugging in. The rated input is 5V DC 1.0A.
The SKN by conair pore purifier advanced™ microdermabrasion tool handle, attachment heads and charging cable have no serviceable parts. If any component is damaged, it must be replaced. Call 1-800-3-CONAIR to purchase replacements.
SAVE THESE INSTRUCTIONS
SENSITIVITY AND CAUTIONS
SPECIAL CAUTIONS FOR DELICATE AREAS
The SKN by conair™ Microdermabrasion Tool is designed to gently clean your
pores and exfoliate your skin without irritation, for healthy-looking results.
If you are under a doctor’s care for any skin condition, or if you think you
have very sensitive skin, please consult your physician before use.
We recommend starting on the LOW SPEED/SUCTION setting and increasing to HIGH
SPEED/SUCTION, depending on how your skin reacts to treatment. If rash or
irritation occurs, stop use.
This is not a medical device and is not intended to be used to treat any
medical conditions.
We recommend not sharing the device. If you experience any pain or discomfort
during use, stop using and consult your physician.
SKN BY CONAIR PORE PURIFIER ADVANCED™
MICRODERMABRASION TOOL
FEATURES
TWO SPEED OPTIONS
The two speeds available on your SKN by conair pore purifier advanced™
microdermabrasion tool allow you to customize your skincare routine to suit
your individual needs.
WARM PLATE
The warm plate on the bottom of the tool helps to open pores, leaving skin
feeling bright and smooth.
ATTACHMENTS
SMALL PORE EXTRACTOR: To remove blackheads & whiteheads.
LARGE PORE EXTRACTOR: To target clogged pores.
2 CRYSTAL DIAMOND HEAD TIPS: For deep exfoliation.
NOTE: Your SKN by Conair may only include certain attachments. See
retailer or call 1-800-3-CONAIR for additional attachments.
RECHARGEABLE
The SKN by conair pore purifier advanced™ microdermabrasion tool is cordless
and requires a full charge before use. After tool is fully charged, it can
provide up to 120 minutes of use without recharging.
OPERATING PRECAUTIONS
This device has a built-in rechargeable lithium-ion battery.
Do not throw device into fire, apply heat to it, or charge, use in a high-
temperature environment.
CHARGING THE SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL
- Before using the SKN by conair pore purifier advanced™ microdermabrasion tool for the first time, it must be fully charged for 2.5–3.5 hours. Plug the DC jack into the side of the unit, then plug power cable and adapter into wall outlet. The white LED will begin to flash, indicating that the tool is charging.
- The charging indicator will FLASH WHITE when charging. Once fully charged, the light will illuminate SOLID WHITE. Always check to be sure that the charging light illuminates when you plug the charging cable into the outlet.
- The white light will start flashing for 5 seconds and then shut off when the unit reaches low battery capacity during operation.
- The adapter may become warm while charging — this is normal. Once fully charged, the device can provide 120 minutes of use.
- In order to maintain the optimum capacity of the rechargeable battery, the SKN by conair pore purifier advanced™ microdermabrasion tool should be given a full 2.5–3.5-hour charge every 3 months.
- Remove charging cable from unit and unplug adapter from outlet when not in use. Do not unplug the adapter from the wall when it is still connected to the unit. This will cause the battery to discharge.
STARTING THE SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION
TOOL AND SELECTING THE SPEED/SUCTION LEVEL
Press the power button once to turn on the device in low speed/suction. For a
deeper exfoliation or stronger suction, press button 2 times for high
speed/suction. The corresponding light will illuminate.
STOPPING THE SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION
TOOL
At any time, the SKN by conair pore purifier advanced™ microdermabrasion tool
can be stopped by pressing and holding the power switch button for more than 1
second.
TURNING ON THE WARM PLATE
Press and hold the Warm Plate Button for 1 second to activate the WARM PLATE.
After 5 minutes in this setting, the device will go into standby mode.
TURNING OFF THE WARM PLATE
At any time, the WARM PLATE can be stopped by pressing and holding the Warm
Plate Button for more than 1 second.
ATTACHING AND REMOVING MICRODERMABRASION/PORE EXTRACTOR HEADS
To attach the different attachments, hold the unit and push the attachment
onto the post until it snaps in place. To remove attachment head, simply pull
attachment off of the unit.
OPERATING INSTRUCTIONS
Warm Plate and Attachments
- Thoroughly cleanse and dry the skin.
- To open pores for better results, use the warm plate before using the microdermabrasion or pore extractor attachments.
- Test warm plate on a small area of the neck or forearm.
- Applying light pressure, slide the warm plate gently over the facial skin. Apply in such a way that it gently warms the skin.
- When warm treatment is complete, turn off and continue with microdermabrasion attachments.
- Test microdermabrasion attachment on a small area of the neck or forearm.
- Pull the skin taut with your free hand to allow the device to smoothly glide over the skin.
- Move device in an upward, fluid motion across the skin. Do not hover in any spots. Do not use directly above or below eyes.
- Immediately after treatment wash and dry the skin.
- Apply a calming toner and recovery moisturizer.
- Clean the attachment heads and unit, including the warm plate, after each use. See User Maintenance Instructions for more information on cleaning the device and heads.
- Wait 6 to 7 days between treatments.
NOTE: Do not do more than two passes over the same area during treatment.
USER MAINTENANCE INSTRUCTIONS
SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL
It is recommended to clean attachment heads and device after each use. If not
clean, performance could be affected. Change the filter if the suction
strength is weak. Remove attachment head, peel off metal filter, stick on new
filter, and reattach the microdermabrasion tip.
- After each use, wipe the handle with a damp cloth. The attachment heads and filters can be rinsed with soapy water, but the handle is not waterproof and cannot be rinsed under water or any other liquid. Also, do not put unit in dishwasher for cleaning.
- After cleaning, wipe all parts with a dry cloth and store in a clean, dry place.
TROUBLESHOOTING GUIDE
SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL IS NOT
CHARGING
NO WHITE FLASHING CHARGING LIGHT. THE CHARGING
LIGHT DOES NOT CHANGE TO SOLID WHITE.| 1. Make sure the contacts on the unit
and charging cable are clean.
See User Maintenance Instructions for cleaning procedure.
2. Make sure the unit is plugged in properly.
3. Check the outlet and make sure the power is on. Most bathroom
outlets have a test and reset button. Press the reset button and recheck the
outlet.
---|---
SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL WILL NOT TURN
OFF.| You must hold the top power button for more than 1 second to turn the
unit off.
SKN BY CONAIR PORE PURIFIER ADVANCED™ MICRODERMABRASION TOOL OR ATTACHMENTS
FALL OFF DURING USE.| Make sure the attachments are snapped on properly.
BATTERY DISPOSAL
The battery is sealed inside the SKN by conair pore purifier advanced™
microdermabrasion tool so it cannot be easily removed for recycling. The
entire SKN by conair pore purifier advanced™ microdermabrasion tool should be
returned when recycling the battery for this product.
Bring the device to the nearest collection center for proper disposal. DO NOT
throw the device into the general municipal waste system.
CONTAINS LITHIUM-ION BATTERY. MUST BE COLLECTED, RECYCLED OR DISPOSED OF
PROPERLY. DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.
RBRC™ is a trademark of the Rechargeable Battery Recycling Corporation.
To find a battery recylcing center near you, call
1-800-822-8837 or go to
www.call2recycle.org/locator/.
LIMITED ONE-YEAR WARRANTY (U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your unit free of charge for 12
months from the date of purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the defective product to the
service center listed, together with your purchase receipt. California
residents need only provide proof of purchase and should call 1-800-3-CONAIR
for shipping instructions.
In the absence of a purchase receipt, the warranty period shall be 12 months
from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS
WRITTEN, LIMITED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation of special, incidental,
or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
WARNING:
IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water are a dangerous combination. But did
you know that an electrical appliance is still electrically live even if the
switch is off? If the plug is in, the power is on. So when you are not using
your appliances, keep them unplugged.
ALWAYS UNPLUG SMALL APPLIANCES
FCC MARKINGS
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by Conair LLC, the manufacturer of this product and the party responsible for compliance, could void the user’s authority to operate the equipment.
SUPPLIER’S DECLARATION OF CONFORMITY
Brand: SKN by Conair
Model No.: MD03
Description: Pore Purifier
Advanced™ Microdermabrasion Tool
Responsible Party: Conair LLC,
1 Cummings Point Road, Stamford, CT 06902
203-351-9000
Standards: FCC Part 15 Subpart B, ANSI C63.4-2014
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesirable operation.
DATE OF ISSUE: TBD
Please register this product at
register.conair.com
SERVICE CENTER CONAIR LLC
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
Visit us on the web at www.conair.com
©2022 Conair LLC Glendale, AZ 85307 stock.image
MD03 Models
22PS082977
IB-17605
Documents / Resources
| skn
MD03 Pore Purifer Advanced Microdermabrasion
Tool
[pdf] Instruction Manual
MD03 Pore Purifer Advanced Microdermabrasion Tool, MD03, Pore Purifer Advanced
Microdermabrasion Tool, Advanced Microdermabrasion Tool, Microdermabrasion
Tool
---|---
References
- call2recycle.org/locator/
- Welcome | Conair
- Call2Recycle | Leading the Charge For Battery Recycling
- Conair LLC Consumer Products for Haircare, Beauty, Wellness, Home and Travel
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>