CloudAPI Inclusion or Exclusion
Installation Guide

CloudAPI Inclusion or Exclusion

This device is a security enabled Z-Wave Plus™ product that can use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products.

D.1 CloudAPI – Inclusion/Exclusion

Inclusion S0 device:
For inclusion one Z-Wave™ device is in add mode and the other one is in learn mode.

1. Include a Z-Wave device (Door lock, Switch, Dimmer…), click button
2. Then pop up the inclusion mode window, display searching for Z-Wave Device
3. Press the button on the device which you want to include, wait for the inclusion to end, display device information, click done
4. View Z-Wave device list, the newly registered device should show

Inclusion S2 device:

1. Include a Z-Wave S2 device, click button
2. Press the button on the device which you want to include, wait for a dialog and input first 5 digits DSK, click Ok
3. wait for the inclusion to end, display device information, click done
4. View Z-Wave device list, the newly registered device should show

Exclusion:
For exclusion one Z-Wave device is in removing mode and the other one is in learn mode.

1. Exclude a Z-Wave device (Door lock, Switch, Dimmer…), click button 
2. Then pop up the exclusion mode window, display deleting for Z-Wave Device
3. Press the button on the device which you want to exclude, wait for the exclusion to end, display device information, click done

D.2 CloudAPI – Device information

Device information:

1. Click ****button, Device information should display: Device name / Device Type / Node ID / Product ID / Product Type/ Vendor Name
2. Display device information

D.3 CloudAPI – Basic operation

Basic Z-Wave device operation:
Basic operation of Switch on the Cloud API interface

1. Device is already registered（Switch as an example）
2. Click button, control switch ON/OFF

D.4 CloudAPI – Network information

Network information:

1. Click button
2. Display Z-Wave Network information

D.5 Controllers – Replication

Controller replication (Copy) is achieved through Inclusion and Set Learn Mode.
Entering learn mode while in a network will trigger a replication if the primary controller is in add node mode. So, replication and Learn Mode are the same and you just need to do Learn Mode here.

1. Prepare two mains powered Z-Wave DUTs and cloud API web shows as below

   2 DUT do factory reset first,![Z Wave CloudAPI Inclusion or Exclusion -

   factory reset](https://manuals.plus/wp-content/uploads/2023/03/Z-Wave- CloudAPI-Inclusion-or-Exclusion-factory-reset.jpg)

2. Click “Inclusion Mode” on the 1#

3. Click “Enter Learn Mode” on the 2#

D.6 Controllers – Learn Mode

1. Click “Enter Learn Mode” on the web
2. Then will show this DSK pin information

D.7 Controllers – Including the DUT

1. Prepare two mains powered Z-Wave DUTs, #2 DUT do factory reset first.
2. Click “Inclusion Mode” on the 1#
3. Click “Enter Learn Mode” on the 2#
4. Then you will see DSK information below, remember the first five numbers underline.
5. Soon 1# web will pop out the DSK input box, fill the box with the first five numbers shows in 2#, and then click OK button
6. Later will shows the 2#’s information, then click DONE button, refresh the 1# web, in the Z-Wave list, it will show the new included controller info, it means the operation of including the DUT successfully

D.8 Controllers – Basic Documentation

This product supports Basic Command and can give action if received a Basic Command.

D.9 Terminology

Z-Wave functionality| Documentation terminology| Example
---|---|---
Inclusion| Add| The process of adding a node to the Z-Wave network.
Exclusion| Remove| The process of removing a node from the Z- Wave network.
Replication| Copy| The process of copying network information from one controller to another.

D.10 Devices from multiple manufacturers in one network

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

D.11 Documentation for Association CC

The association group available in our product is described as follows.

D.12 Documentation related to BASIC commands

The Basic Command Class mapping is listed below. Basic set and basic get commands are described separately.

D.13 Documentation related to BASIC commands

The following basic commands are used for our product to control some devices.

commands
0x00
On/Off Switch| Switch Binary Set| 0xFF| Turn on
0x00| Turn off
Power Strip| Switch Binary Set| 0xFF| Turn on
0x00| Turn off
Switch Multilevel Set| 0xFF| Turn on
0x00| Turn off
Fan Switch| Switch Multilevel Set| 0xFF| Turn on
0x00| Turn off
Light Dimmer Switch| Switch Multilevel Set| 0xFF| Turn on
0x00| Turn off
Thermostat, HVAC| Thermostat Mode Set| 0xFF| Comfort Mode
0x00| Energy Save Mode

D.14 Documentation for Factory Default Reset

1. Prepare two mains powered Z-Wave DUTs and navigate to system UI as below, click buttonClick “Setting”

D.19 Documentation for S2 Security CC

D.21

D.21.1
Documentation about how to activate any functionality available in the device related to Z-Wave behavior is listed below.
DRAFT COPY – R800-27957A_PROA7
DRAFT COPY – R800-27956A_PROA7-

D.21.2
None

D.21.3
About how to send any controlled command from the controller PC controller tool is preferred.

1. Double click to select the controlled device, you will see the device is in greyed color
2. Double click one command of command classes or secure command classes to choose such as association
3. Choose command in command list and then click send button

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>