CARVISION Hang TFT LCD Monitor with Multi Media User Manual
- June 9, 2024
- CARVISION
Table of Contents
CARVISION Hang TFT LCD Monitor with Multi Media
Please read this Manual thoroughly
before using this product
WIRING
CLEANING
When cleaning the device, do not make connect with water Since chemical
solvents may damage the surface of the unit, do not use them for cleaning.
Use a clean and dry cloth to clean.
ASCCESSORIE
Remote Controls,Wries, Manual, brackets.
PRODUCT OVERVIEW
FRONT PANEL
MULTIMEDIA PLAYER
- LCD Panel
- Open
- Pre/rewind forward
- Next/Fast
- Power 6. –
- menu
- .+
- DC 12V
- DC jacket
- HDMI read port
- AV2 In jack
- Earphone jack
- USB read port
- SD read port
SIDE PANEL
- Power
- Earphone/AV2 jack
- USB .SD
- DC 12v Jacket
- 2.5.HDMI PORT
REMOTE CONTROL
SPCIFICATION
- TFT LED New Panel
- Compatible: DVD/SD/USB/IR
- Kodak picture CD/CD-R/CD-RW/DVD+RW/DVD-RW PAL/NTSC system
- Build in FM transmitter (88.7-106 MHz~2.8MHz)
- Build in SD/USB/Speaker/HDMI PORT
- Full Function Wireless Remote Control
- Operating Temperature:-10℃~+60℃
- Power Supply: DC 12V
Features and functions
- DVD
- Super-slim design
- Dual FM Transmitter
- Audio/video input and output
- Full function remote control
- USB/SD/Wireless games
- Built-in speakers
- Built-in HDMI read port
Specifications
- Size of screen:9inch/10.1 inch
- Pixel:9inch,8003(RGB)480 10.1 inch 10243(RGB)600
- Rated voltage:DC12V(voltage:10V-14V)
- Power :about 12W
Troubleshooting
| Troubles | solutions |
|---|---|
| No sound and image | Power is disconnected ;the machine is not turned on |
| No image | Disc is scratched;signal wire is disconnected |
| No sound | Volume too low or the volume setup is not workable |
| Black screen | Incorrect setup of image luminance and contrast;Undervoltage |
| Blurring and unstable image | Disc is scratched |
| Color cast | function menu setup is incorrect;weak signal |
| No power | Voltage is not accurate :check interconnect circuit;Fuse is |
disconnected:change fuse specification
No image after loading the disc| Only audio frequency for the disc; días is
scratched; disc for format is not supported
Instable sound caused by vibration| DVD is dirty or seriously damaged
Instable sound even with no vibration| Disc is dirty or scratched clean or
replace the disc
INSTALLATION
- Take out the machine ,remove the bracket like below
- Remove the screws from bracket like below picture .
- Put the plastic bracket parts in between two metal poles ,at the same time, push 2 screws to fix up bracket.
- Hold up unit,insert the metal plate in black of the unit into plastic bracket parts, then adjust it to the right angle and fix it tightly, at last lower the orignalcar headrest to the appropriate position.
Attention
- Do not put the machine in the rain or damp environment lest outbreak of fire or any damage to machine.
- Do not repair the machine by yourself. Please turn off the machine and inform us if any problem found, the factory or the agent will arrange specialized personnel to disassemble and repair the machine for you .
- Please keep the machine away from dampness,dust,oil and straight sunlight.
- Do not use diluents or other chemicals cleaner when cleaning the machine. Please clean the machine by soft cloth with special cleaner.
- Please keep the machine in a good environment. The storage temperature for this machine is from -20℃ｔｏ６０℃。
- Do not play without the support of disc, this machine supports DIVX/MPEG4/DVD/DVDR+/SVCD/VCD/DVCD/CD/MP3/WMA/CD-R/RW/HDCD+-R/JP EG or CD-ROM7.
- Please prevent the machine from the influence of other equipment.
- For your safety, please do not turn or operate this machine when driving as it may be illeagal in some countries and regions.
- Safe power supply:DC12V（voltage range:10V-14V)
Attention
There may be some small and bright spots on the screen. This is a common
technical matter and does not indicate any quality problem of this machine.
FCC WARNING
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>