Bkav S500-0233 Ultra Zoom Speed Dome AI Based Camera User Guide

Bkav S500-0233 Ultra Zoom Speed Dome AI Based Camera

Qualcomm products contained here in are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.

Model: S500-0233

PRODUCT KIT

TECHNICAL SPECIFICATION

• Power AC24V 5%
• Power consumption Max 35W ,Max 37W (with PTZ)
• Protection standards IP66, IK10
• Resolution, frame rate FHD 1920×1080, Max 60fps
• Digital zoom 4x
• Optical zoom 33x
• Focal length 4.5 – 148.5mm
• Field of view (horizontal-vertical) Near: 60.1° – 36.2° / Far: 2.28° – 1.29°
• Micro SD card External, up to 256GB
• Operating temperature -40°C – 60°C (-40°F – 140°F), Humidity 10 – 100%
• Dimensions (L x W x H) L380 x W290 x H450mm
• Weight 4.67kg

PRODUCT OVERVIEW

INSTALLATION GUIDE

• Step 1: Fix the camera on the bracket and tighten the screws it in the place (Figure 1).

• Step 2: Assemble safety cable into the bracket (Figure 2).
  

• Step 3: Apply positions decal and drill 4 anchors to the wall. Fix the camera onto the wall with the screw (Figure 3).
  

CONNECTING THE SIGNAL WIRE

Connect network signal and 24VAC power supply.

CAMERA FIELD OF VIEW

ATTENTION

Note:

• During a power outage, the camera will be down as shown in the image above.
• When power is on, the camera will return to its previous position.

THE MEMORY CARD AND RESET INSTALLATION

Reset installation: Open the protective cover that protects the camera against dust and water to reset the device.
Memory card: Open the protective cover, you can find the location of Micro SD card.

Note:

• Power off the camera, press and hold the factory reset button. Continue to hold the factory reset button for another 10 seconds while powering the camera, the camera will be restored to factory settings.
• If resetting with the factory reset button is difficult to operate, we recommend resetting via WebUI.

ACCESSING THE CAMERA

Password setting
The IP address of camera is set to DHCP mode by default. For the camera enables the DHCP by default, you need to use the AI View Scanner App to scan IP.

Note: To complete the installation steps for the camera, refer to the User Manual.
The system will ask you to reset the password on your initial access.
When the “Administrator password change” window appears, enter a new password.

• For passwords using eight or nine characters, you need to use at least three of the following types of characters: uppercase and lowercase letters, numbers, and special characters.
• For passwords using 10 to 15 characters, you need to use at least two of the character types. Special characters include: ~ ` ! @ # $ % ^ & * ( ) _ – = + | { } [ ] . ? /
  

Note:

• For additional security, please do not repeat any characters in your password.
• If you forget your password, you can hold the [RESET] button to return the product to its factory settings.

SOFTWARE INSTALLATION

Login screen
When accessing the camera, a login window will appear. Enter your user name and password to access the camera.

1. Enter “admin” in the box.
2. Enter your chosen password in box.
3. Click

SAFETY INFORMATION

Be sure to follow this advice to ensure the device works properly.

Precautions

• Installation instruction: Concrete, brick, column, wood… are all suitable. Make sure the wall is strong enough. The torque forces of screws securing IP enclosure: 1.3 – 1.4Nm.

• It is recommended to use shielded network cables (STP) during set-up.

• It is recommended to use CAT5e or higher network cables.

• Store the camera in a cool and dry environment.

• Shield the camera from potential impact from heavy objects.

• Do not install the camera on unstable pillars, brackets, surfaces, or walls.

• Do not use chemicals or detergents to clean the camera or housing.

• To clean, use a damp cloth.

• Only use standard tools and accessories when installing the camera equipment. The manufacturer recommends using the manufacturer’s power supply equipment or a corresponding source for the camera. Improper installation may cause damage to the product.

• Contact Bkav’s customer support or authorized Bkav agents if you experience any problems.
  This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-ant to part 15 of the FCC rules. These limit are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in a accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Transportation:

• Use the original packaging, or equivalent, to avoid damaging the product during transportation.

WARRANTY INFORMATION

For information about AI View product warranty and thereto related information, go to aiview.ai/warranty.

BKAV CORPORATION
Address: 2nd Floor, HH1 Building, Yen Hoa Urban Area, Yen Hoa Ward, Cau Giay District, Hanoi City, Vietnam
Website: www.aiview.ai
Email: aiview@bkav.com

References

• Bkav AI View | Camera AI | Giải pháp tổng thể sá»­ dụng trí tuệ nhân tạo AI trong việc quản lý, vận hành hệ thống Camera | Bkav Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>