WEIKING BT265-6 Portable Party Speaker User Manual

BT265-6 Portable Party Speaker
User Manual User Manual
BT265-6 Portable Party Speaker

Package Contents

BT265-6 Portable Party Speaker
USB Type-C Charging Cable
3.5mm Audio Cable
User Manual

Product Diagram

① Power Button
② Led Indicator
③ Volume Down /Previous Track Button
④ Handsfree Mic
⑤ Play/Pause
⑥ Volume Up/ Next Track Button
⑦ Equalizer/ Sound Effect
⑧ Battery indicator| ⑨ Light ON/OFF Button
⑩ 6.5mm Microphone Input
11.Reset
12.Power Bank output
13. AUX
14. USB Type-C Charging Port
15 TF-card Slot
---|---

Specification

Operation Instruction

Charging

• Fully Charge this speaker before first use.
• Use the included USB Type-C charging cable and a 5V 2A power adapter to charge your speaker. The power adapter is NOT INCLUDED.
• When there are 3 solid white lights, your speaker is fully charged and ready for use.

Battery

Low battery alarm
(When battery voltage lower than 6.8V (20%) & 6.5V (10%))| Red LED flashes
Automatically turn off at low battery
(When battery voltage lower than 0%)）| /
Input voltage/current| TPYE-C USB 5V/0.5A-2.4A
Charging time| Around 3.5hours

Power On/Off

Actions| Operation|

LED status

---|---|---
Power on| When the speaker on power off status, press and hold the power button for 2 to 3 seconds.| Blue LED on
Power off| When the speaker on power on status, press and hold the power button for 2 to 3 seconds.| LED turns off

Connection Way

1.Bluetooth Pairing

flash
Connected| Select the Bluetooth pairing name “BT265” on mobile phone.| Blue LED stays on (successfully poked)
Disconnected manually| Press volume + and volume – at the same time for 1 second.| Blue LED stays on (successfully paired)
Reconnect| Speaker will reconnect with Iasi device when power on.| Blue LIBD stay on

2.Other Connection Way

stays on
Outdoor mode Play: green LED flashes slowly Mute: green LED flashes
TF-Card mode| Insert TF-card to enter TF-card mode.| Indoor mode Play: green LED stays on Outdoor mode Play: green LED flashes slowly Pause: green LED flashes
BT Mode| When play In Bluetooth mode.| Indoor mode Play: blue LED stays on
Outdoor mode Play: blue LED flashes slowly
Pause: blue LED stays on
Switch Mod tooth/(Blue,
AUX/TF-card)| Short press power button to switch . (Note: The mode can only be changed when there are more than two connection modes at the same time.)|  /

Note:

• If a code or pin is required for pairing, please enter “0000”
• The speaker will automatically shut down after 10 minutes in pairing mode if no devices are paired.
• If speaker can not enter pairing, please reset the speaker to clear the pairing list or any program erros.
• The speaker can remember last volume and mode, it will continue at the same status when turns on again.
• If your paired device is switched off or manually disconnected, the speaker will enter pairing mode and automatically shut down after 10 minutes.
• If the speaker or connected device exceeds the operating range, the speaker will disconnect. The connection to the last successfully connected device will be reestablished once you re-enter wireless range within 10 minutes. To connect to other devices, please repeat the previous “Pairing” steps.

Hands-Free Calling

Blue LED stays on
Hang up| During a phone call, press the “play/pause” button.| Blue LED stays on
Reject the cal| When receive a call, long-press the “play/pause” button.| Blue LED stays on

True Wireless Stereo

and green LED flash
(moster speaker)
Connection between two speakers| Successfully connected. (do nothing, just wait pairing)| Slave speaker
blue LED stay on, blue LED on
master flash slowly
Connect with mobile| When”True Wireless Stereo”successfully connected, open Phone’s Bluetooth to search and connect the master speaker.| Master and slave speaker blue LED stay on

Note: In “True Wireless Stereo”mode, only the master speaker has phone call function.
Basic Control

Treble(outdoo LED slowly flashes
Turn on/Off Light Mode| Short press “ light mode button| /
Reset| Press the reset button| LED turns off

Microphone function (The following situations are all after the microphone is plugged)

“bee-“, then short press “Volume +/-” buttons to adjust volume.
Mic-reverberation Mode| Press and hold the “Equalizer’ button until you hear TWO “bee- bee-“. then short press “Volume +/-” buttons to adjust mic- reverberation volume.
Music Volume| When you enter mic volume mode or mic-reverberation mode, 10 seconds of no operation will automatically enter the music volume, then Short press “Volume IF buttons to adjust music volume.

Power bank function
When the speaker turns off, press the power button to turn on power bank. And connect the USB output port with your phone for charging, if there is no any charging after 10 seconds, it will turns off automatically.
When the speaker turns on, the power bank function always turns on, just plug the phone to charge.
Battery indicator:
Under 7.2V (30%): the first white LED Flashes
7.2v-7.8v (30%-70%): the second white LED flashes
Above 7.8V (70%): the third white LED flashes
Product Care & Use

• Keep away from liquids, extreme heat, and strong magnetic fields.
• Do not use this speaker at high volume for extended periods, as this may cause permanent hearing damage or loss.

Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by SHENZHEN WEIKING TECHNOLOGY CO.,LTD may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
RF exposure statement: This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.
ISED Statement
– This device complies with Industry Canada license – exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
For Receiver : This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. The device is inst alled and operated without restriction.
For Transmitter: This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>