OSCULATI 29.531.00 Bluetooth Dashboard Amplifier Owner’s Manual
- June 9, 2024
- OSCULATI
Table of Contents
OSCULATI 29.531.00 Bluetooth Dashboard Amplifier
OWNER’S MANUAL
Code 29.531.00
Please read the instruction carefully before operating the unit
Installation
ATTENTIONS OF INSTALLATION
- This player should be installed by professional technician.
- please read the instruction and operation of equipment carefully before installing.
- Make sure to connect other wires before power connection.
- To avoid short circuit. Please make sure all the exposed wire are insulating.
- please fix all the wires after installation.
- please make connection to the player accordingly to this instruction manual. Wrong connection may cause damage.
- This player only fit for 12V DC device and please make sure your car belongs to this kind of cathode grounding electrical system.
- Please connect the wires rightly. Wrong connection will cause malfunction or damage the electrical system.
WIRING CONNECTION
- This player can only be used by the 12V DC cathode grounding electrical system.
- Do not connect the battery terminal until the player is fully well installation.
- Please make sure to connect the yellow wire to the positive of the battery(+).
- When change the fuse. Please make sure the specifications are same.
- Using good quality speaker with 4-8 ohm can result in the best effect of the equipment.
KEY FUNCTION
LOCATION OF KEYS
- USB source button
- BT source button
- VOL button
- PAUSE button
- Next track button
- previous track button
- SUB volume+ button
- SUB volume- button
- AUX source button
TROUBLE SHOOTING
-
Turn on/off the unit
Press VOL knob to turn on the unit. When the unit is on. Press and hold this button to turn off the unit. -
Volume up/down
Rotate the VOL knob to up/down the volume. -
Volume up/down
Press SUB+/SUB- button to up/down the subwoofer volume. -
Mute on/off
Press VOL knob or “>II” button to mute on/off the sound. -
AUX in operation
Press AUX button to switch to AUX source when an audio signal is inserted. -
USB operation
Press USB button to switch to USB source. Or insert an USB it will switch to the USB source automatically. -
Select file
Press button to skip to next/previous file. Hold button to fast forward or fast reverse. -
Play/Pause
Press button to pause/playing the file.
Bluetooth Operation
-
Pairing
On mobile phone, select the Bluetooth item searching the Bluetooth device. “CAR KIT” should appear in the list, select “CAR KIT” and then input password “0000” If it needs a password. When successful paired, the BT button will be not flashing. -
Bluetooth Audio
Press BT button to switch to BT source. It will play a song of your mobile phone automatically. Press “>II” key to pause/play the song. Press button to selectnext/previous song.
TROUBLE SHOOTING
GENERAL
- Power Supply Requirements : DC 12 Volts, Negative Ground
- Chassis Dimensions : 100(W) x 100 (D) x 70(H)
- Tone Controls
- Bass (at 100 Hz) : ±10 dB
- Treble (at 10 kHz) : ±10 dB
- Maximum Output Power : 4 x 40 watts
- Current Drain : 10 Ampere (max.)
Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer.
| Symptom | Cause | Solution |
|---|
No power.
| The car ignition switch is not on.| If the power supply is connected to the
car accessory circuits, but the engine is not moving, switch the ignition key
to “ACC”.
The fuse is blown.| Replace the fuse.
No sound.
| Volume is in minimum| Adjust volume to a desired level.
Wiring is connected.| not| properly| Check wiring connection.
The keys work.| operation do not| The built-in microcomputer is not
operating properly due to noise.| Press the reset button.
The radio does not Work. The radio station automatic selection does
not work.| The antenna cable is not connected.| Insert the antenna cable
firmly.
The signals are too weak.| Select a station manually.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>