DANFI AUDIO TE-2030 Vintage Bluetooth Turntable Record Player Instruction Manual

June 9, 2024
DANFI AUDIO

DANFI AUDIO TE-2030 Vintage Bluetooth Turntable Record Player

DANFI AUDIO TE-2030 Vintage Bluetooth Turntable Record
Player

Instructions Before Start

Read the manual before using this product. Keep these instructions for future reference.

About Records
  1. Never use a record with cracks or warps.
  2. Never use a record that is cracked or warped, as this may cause extreme wear and destruction of the needle.
  3. Never use unusual play methods such as scratching. This unit is not designed for such playback.
  4. Do not expose the unit to direct sunlight, high temperature or high humidity. This may cause warping or deformation. When holding the record, hold only the label or the outer edge.
  5. Do not touch the record groove. Dust and fingerprints may cause distortion of the sound. Care of the record
  6. Use a special record cleaner and cleaner solution (sold separately). Wipe the record cleaner in a circular motion along the record groove.
About Bluetooth
  1. This unit has built-in Bluetooth receiver and will be automatically turned on when the turntable is on, to stop the Bluetooth, disconnect from your devices or change to turntable function.
  2. Bluetooth used in this unit use the same frequency band (2.4GHz) as wireless LAN devices (IEEE802.11b/g/n), so if they are used near each other, they may interfere with each other, resulting in reduced communication speed or connection failure. In this case, please use it as far away as possible (about 10m).
  3. We do not guarantee the connection with all Bluetooth devices.
  4. Also, depending on the conditions, it may take some time to connect.

Introduction

Main features
  • 3 speed turntable plays 33 1/3, 78, and 45 rpm records;
  • Auto stop function
  • Supports Bluetooth Input
  • Aux In 3.5mm audio input
  • 3.5mm headphone jack input
  • Built-in stereo speakers
  • Auto-stop functionality
  • Bass and Treble
  • RCA stereo audio outputs
Accessories Includes
  • 45 rpm adapter
  • 1x Stylus needle( installed)
  • AC/DC power adapter
  • User’s quick guide
  • User’s manual
Received a defective record player ?

Notice:

The gap between the case and the spinning mechanism is for vibration- absorbing, it’s a commonly used design for starter turntable, which could be considered being defective mistakenly.

Please use below contact Customer Service.
e-mail: support25@163.com

PARTS ILLUSTRATION

Parts Illustration

  1. Turntable Platter 8. Stylus
  2. Turntable spindle 9. Speaker
  3. 45 RPM adapter 10. Power ON-OFF Volume button
  4. Tone arm lift lever 11. Control panel
  5. Speed selection switch 12. Bass and Tremble tune
  6. Auto stop on/off switch 13. 3.5mm AUX input
  7. Tone arm lock 14. 3.5mm Headphone jack

Rear Inputs

Rear Inputs .

Connecting the main unit to Power

Connecting the main unit to Power

  1. Plug the power cord into the DC Input on the back of the unit.
  2. Then plug the USB side into a the DC adapter included.
  3. Plug in the adapter into the Standard wall power outlet. Dedicated

AUX Connection Priorit Above Bluetooth and Turntable

Priority Note:

  1. The AUX-IN (audio input) have top priority. If the AUX-IN (audio input) cable is connected, the AUX-IN this connection will take priority and you will not hear the Bluetooth connection sound or sound from phonograph turntable. And the turntable will stop spinning.

Operation—Plaing a Record

It is recommended that you use extreme care when manipulating the tone arm, stylus, and other components of this turntable. These parts are very sensitive and can easily break or become damaged if they are carelessly handled.

Operation---Plaing a Record

  1. Turn the the Power ON/OFF volume button clockwise till the LED display lights up, if not, check the power and adapter.
  2. Remove the shroud that protects the stylus, and release the lock that holds the Tone Arm in it’s resting position.
  3. Before use, turn the turntable clockwise about 10 times by hand to make sure there is no belt shift or kinks from the pulleys.
  4. Select the correct turntable speed based on the type of record you wish to play, and place the record on the turntable. If you are playing a 45 rpm record, use the included adapter and place it between the turntable and the record.
  5. Use the Tone Arm Lift Switch to raise the Tone Arm from its catch.
  6. Using your hand, gently swing the Tone Arm into the desired location over the record. The turntable will start spinning as the Tone Arm is moved into position.
  7. Use the Tone Arm Lift Switch to safely lower the stylus onto the record. Using the Lift Switch instead of your hand will reduce the chance of accidentally damaging the record or the stylus.
  8. Slide the Auto Stop Switch to ON to enable the Auto Stop feature. When the record is finished playing, it will automatically stop the turntable. Use the Lift Switch to raise the stylus off of the record, and gently return the Tone Arm to the catch by hand.

Note: Some records place their Auto Stop area outside of the range of this unit. In these cases, the record will stop playing before the last track is reached. Set the Auto Stop Switch to OFF and use the Tone Arm Lift Switch to safely raise the stylus off the record when the end of the record has been reached.

Operation---Plaing a Record

Bluetooth Input— pairing with Bluetooth Devices

  1. Turn on the turntable by tuning the Volume/ON&OFF button to the right till the Blue light indicator flashes up.( If the indicator is in red color and turntable moves up, it’s in phonograph mode, you can switch to Bluetooth by turning “AUTO STOP” button to ON or put the raise lever into the rest position).
  2. Using the controls on your Bluetooth device, search for and select “TE-2030″in your Bluetooth settings to pair. If your  device requests a password, enter the default password “O O O O” and press OK.
  3. When successfully paired and connected, the indicator will stop flashing up and an audible chime will sound. After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a reset of the device. If your device should become unpaired or you find it is unable to connect, repeat the above steps.
  4.  Play, pause or skip a selected track using the controls on the connected Bluetooth Device.
On an iPhone
  • Goto SETTINGS> BLUETOOTH Search for devices (Make sure Bluetooth is tur ne d ON)
    Bluetooth Input--- pairing with Bluetooth Devices
On an Android Phone
  • Goto SETTINGS> BLUETOOTH Search for devices (Make sure Bluetooth is turned ON)
    Bluetooth Input--- pairing with Bluetooth Devices

Disconnected from Bluetooth Devices

  1. Disconnect the BT connection from your external devices. Turn off the Bluetooth function on your devices.
  2. The Bluetooth will be disconnected automatically if turntable moves up, by turning “AUTO-STOP” button to OFF or unlock the raise lever and move it to the turntable from the rest position.
  3. When the indicator goes red it and means the it’s entering into phono mode and ready for playing records.
  4. when the AUX cable is plugged in, the Bluetooth will be disconnected.

Use Bass and Treble Tone

Reminder:

It’s suggested that users DON’T tune the Bass tone to the maximum, which will make any kind of audio in a extremely Low Volume.

  1. Use the “TONE” knob to adjust the sound effect as “BASS” and” TREBLE”.
  2. To the left for Bass and to the right for Treble.

Use 3.5mm headphone jack

  1. Plug in the headphone jack and listen privately.
  2. if you use a headphone with type-c connector, use a type-c to 3.5mm connector

RCA Connecting to External Systems

RCA Audio Output

Requires RCA audio cables (red/white, not included). Use to connect the turntable to an external stereo, television, or other source.

  1. Connect RCA audio cables to the RCA Audio Output on the back of the turntable, and to the audio input of an external stereo system.
  2. Adjust the external stereo system to accept input from the turntable.
  3. Audio played through the turntable will now be heard through the connected stereo system.
    RCA Connecting to External Systems

AUX IN Connecting to Audio Source

Requires 3.5 mm audio input cable (not included).

Note: When the Source selector is set to Aux In, When a 3.5mm audio cable is plugged into the unit, it will automatically detect the input and power ON in Aux In mode.

  1. Plug a 3.5 mm audio input cable into the Aux In on the unit and the audio output/headphone output on an MP3 Player or other audio source.
  2. Use the controls on your connected music player to select and play audio.
  3. Audio played through the connected device will now be heard through the speakers.
  4. The Bluetooth will be disconnected when the AUX input jack is plugged in.
    AUX IN Connecting to Audio Source

HOW TO REPLACE THE NEEDLE

The durability time of the recoil needle is about 200-250 hours. Replace the needle if necessary.

Remove the Needle
  1. Gently pull down the front edge of the needle.

  2. Pull needle forward.
    How To Replace The Needle

  3. Pull out and remove.
    How To Replace The Needle

The stylus needle is universal type for Victrola and Crosley record player, purchasable on Amazon.

Installing Needle
  1. Position the needle with its tip facing down.
    How To Replace The Needle

  2. Line up the back of the needle with the cartridge.
    How To Replace The Needle

  3. Insert the needle with its front end at a downward angle and gently lift the front of the needle upward until it snaps into place.
    How To Replace The Needle

Troubleshooting

There is no power
  • Contact the seller for help
  • Power adapter is not connected correctly.
  • No power at the power outlet.
  • Use the wrong adapter instead of he original one included.
  • Power button is not turned on, turn the volume/ON/OFF button clockwise to turn on.
My record is skipping
  • The needle is not in the middle of the stylus or broken, replace it.
  • Use the tone arm lift raise up and down the arm for 10 times before initial spinning.
  • Change vinyl records or clean the vinyl records grooves properly.
  • Put the record player on the flat surface with 4 legs/corners on the ground.
  • The white stylus protector is till on.
  • Contact the seller for help
Power is on, but the platter does not turn
  • Move the lever and check if the platter moves, if it is not, Turntable drive belt has slipped off. Contact the seller for help.
  • An aux in cable is plugged into the aux in jack, unplug it.
  • Contact the seller for help
Turntable is spinning, but no sound, or not loud enough
  • Volume is too low, turn it clockwise to volume up. Adjust the BASS
  • Stylus protector is still on.
  • Volume is not loud enough or not good to you: Adjust the BASS or connect to the external powered speakers.
  • Contact the seller for help
The arm lifter can not be used to lower the arm down
  • Check if user has raised the lift lever up without unlocking the buckle of the stylus.
  • Pull the tone arm lift lever towards oneself with some strength till pull it down to the front.
  • Contact the seller for help

Specifications

Product Name Vintage Bluetooth Turntable Record Player
Speaker Driver SW*2
Dimension L13.1″ x Dl 0.4″x H4.S2″(L330 x D270 x H11Smm)
Power DC5V ![Icon](https://manuals.plus/wp-content/uploads/2023/03/DANFI-

AUDIO-TE-2030-Vintage-Bluetooth-Turntable-Record-Player-Instruction- Manual-18.png)
Input Connections supported| 1 x 3.5mm Aux jack 1 1 x Bluetooth input
1 x 3.5mm headphone jack
Power Output| 5 Watts
Power Input:| 5V/1A
3 Speeds| 33; 45; 78 rpm

FCC Statements

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Exposure Statement
The distance between user and products should be no less than 20cm.

FCC ID: 2A453-TE001
Made In China

CUSTOMER SUPPORT

AUDMIC INDUSTRIAL LIMITED Questions, problems, missing parts? CONTACT—support25@163.com Before returning to Amazon, please use above contact for Customer Service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals