Trust 71167 Compact Wireless Socket Dimmer User Manual

: June 9, 2024
: Trust

Table of Contents

ACC-250-LD COMPACT WIRELESS SOCKET DIMMER
TRUST SMART HOME
Trust Electronics Ltd.
TECHNICAL SPECIFICATIONS
SUPPORTED LOAD
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trust 71167 Compact Wireless Socket Dimmer User Manual

ACC-250-LD COMPACT WIRELESS SOCKET DIMMER

Place the socket dimmer
- A Connect your lighting to the dimmer and plug the dimmer into a power outlet.
- B The socket dimmer will activate the pairing mode for about 6 seconds and the LED on the socket dimmer will blink green.
Pair the socket dimmer with a transmitter
- A After plugging in the socket dimmer, send an ON signal (during the pairing mode) with a Trust Smart Home transmitter.
- B The lighting goes on and off 2x to confirm that the pairing has succeeded. The LED on the dimmer will also flash quickly and then go off. The dimmer can store up to 32 different channels in the memory. The paired transmitters will be remembered when the socket dimmer is moved to another power outlet.
Operating the socket dimmer
- A Press the ON button with the assigned channel on the paired transmitter to turn the lighting ON. Press the OFF button with the assigned channel on the paired transmitter to turn the lighting off.
Manual On/OFF switch
With the ACC-250-LD you can manually switch your light ON or OFF by pressing the button on the housing.
Activate dimming sequence
- Press the ON button on the transmitter to turn the receiver on.
- Press ON again to activate the dim sequence.
- Press ON a third time to lock the desired dim level The dim sequence will stop and automatically lock the dim level at the highest or lowest point when no input is given with a transmitter.
Adjust the dimming range
If the connected LED lighting does not dim deep enough
or vibrate, you can adjust the lower limit of the dimming range. Press the ON button on the transmitter to turn the receiver on.
- A Press and hold the button on the housing (ca. 3 sec) until the LED flashes twice. You can now adjust the dimming range. The mode to adjust the dimming range lasts for 30 seconds.
- B Press the OFF button on a paired transmitter to increase the dimming range one step. The connected LED lighting will then become less bright, so the dimming range will increase. In order to reduce the dimming range with one step, press the ON button to make the lighting more bright.
- C Press the button on the housing shortly to set the selected dimming range. The LED flashes quickly and your light goes on and off twice to confirm the dimming range.
Select dimming mode.
If your lighting vibrates, you can choose a different dimming mode.
- A Press the ON button on the transmitter to turn the receiver on.
- B Press and hold the button on the housing (ca. 10 sec) until the LED flashes 4 times fast.
- C Press the button on the housing shortly to switch to leading or trailing edge dimming. The LED on the housing flashes quickly and your lighting goes on and off 2x to confirm the selected dim mode.

With leading edge, the LED will light up 1x when the dimmer is switched on or off. With trailing edge, the LED will blink 2x when the dimmer is switched on or off.

RLC (Leading edge): Dimmable incandescent-, halogen-, LED -lamps and lamps with a traditional (wound coil) dimmable transformer
RC (Trailing edge): Dimmable incandescent-, halogen-, LED -lamps and lamps with an electronic dimmable transformer

Should your lighting still vibrate then check whether your lamp is dimmable or try another dimmable lamp.

Optional: Unpair the socket dimmer from a transmitter

A Remove the socket dimmer from the power outlet. Plug the socket dimmer back in the power outlet. The pairing mode will be activated for about 6 seconds and the green LED will blink.
B While the pairing mode is active, send an OFF signal with the assigned channel on the paired transmitter to unpair it.
C The lighting goes on and off 2x to confirm that the unpairing has been successful. The LED on the dimmer will also flash quickly and then go off.

Optional: Clear the memory of the socket dimmer

A Remove the socket dimmer from the power outlet. Plug the socket dimmer back in the power outlet. The pairing mode will be activated for about 6 seconds and the green LED will blink.
B While the pairing mode is active, send an GROUP OFF signal with the assigned channel on the paired transmitter to unpair it.
C The lighting goes on and off 2x to confirm that the unpairing has been successful. The LED on the dimmer will also flash quickly and then go off.

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:

Model: ACC-250-LD Compact wireless socket dimmer
Item number: 71167/71167-02
Intended use: Indoor

is in compliance with the essential requirements and other relevant provisions of the following directives:

ROHS 2 Directive (2011/65/EU) RED Directive (2014/53/EU)
The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

TRUST SMART HOME

LAAN VAN BARCELONA 600 3317DD DORDRECHT NEDERLAND
www.trust.com

Trust Electronics Ltd.

Sopwith Dr, Weybridge, KT13 0NT, UK. All brand names are registered trademarks of their respective owners. Specifications are subject to change without prior notice. Made in China.