Trust ACDB-9000AC Wireless Doorbell Kit with Portable Chime Instruction Manual

: June 9, 2024
: Trust

Trust ACDB-9000AC Wireless Doorbell Kit with Portable Chime

Overview

**A**LED indicator doorbell
**B**Connect button
**C**Volume button
**D**Melody selection
**E**LED indicator push button
**F**Push button

Overview

Wireless control

The wireless doorbell can be operated wirelessly with a minimum of 1 and a maximum of 32 Trust Smart Home transmitters of your choice. For example, you can play a desired melody using the supplied push button.
In addition, you can also play a melody when movement is detected and / or when a window or door is opened.
For each Trust Smart Home transmitter you can set a separate melody to hear exactly whether someone presses the push button or if a door or window is opened.

Remove battery strip from push button

A Insert a flat screwdriver into the notch at the bottom of the push button and slide the push button off the back plate.
B Open the waterproof rubber by flipping it to reveal the battery.
C Remove the plastic battery strip.
D Close the waterproof rubber and place the push button back on the back plate.

Remove battery strip from push button

Installing the doorbell batteries

A Open the doorbell battery compartment by twisting the bottom open towards the open lock icon.
B Insert two 1.5V AA alkaline batteries (not included) as shown. Be sure to pay attention to the correct polarity of the batteries (place plus and minus on the right side).
C Place the bottom cover back on the doorbell.

Installing the doorbell batteries

Make sure that the line on the bottom of the doorbell is in line with the open lock icon. Then turn the bottom side to the closed lock icon.

Selecting the desired volume

First press the volume button to set the desired volume level. There are 4 levels: High, Medium, Low and Off (LED indication only). This volume level applies to all paired transmitters. You can change the volume level if desired.

Selecting the desired melody

Press the melody button to select 1 of the 6 melodies. You can set a separate melody for each transmitter (push button, motion detector, door/window sensor) by selecting it in advance.

Connecting transmitter(s) to the doorbell

A Press the connect button for 1 second to activate the learning mode. The learning mode will be active for 10 seconds and the LED indicator on the doorbell will flash slowly.
B While the LED indicator is flashing, send an ON signal with a Trust Smart Home transmitter to pair it to the doorbell.
C As soon as the transmitter is paired, the wireless doorbell will give 2 short beeps. The transmitter, melody and volume are now paired. The wireless doorbell is now ready for use. The doorbell can store 32 different transmitters in its memory. If you want to pair several transmitters, repeat steps 3 to 5c.

$Connecting transmitter$s$ to the doorbell$

6A. Securing push button with double-sided tape

Determine where to place the push button and attach the push button with the supplied double-sided tape.

Securing push button with double-sided tape

6B. Securing push button with screws

A Insert a flathead screwdriver into the notch on the bottom of the push button and slide the push button off the back plate
B Determine where the push button will be placed and secure the back plate with the supplied screws.
C Place the push button back on the back plate by sliding it from top to bottom.

Securing push button with screws

Unpair a Trust Smart Home transmitter

A Press the connect button for 1 second. The learning mode will be active for 10 seconds and the LED indicator on the receiver will blink slowly.
B While the learning mode is active, send an ON signal with the channel of the paired Trust Smart Home transmitter you want to disconnect
C To confirm, the wireless doorbell will give 2 short beeps.

Unpair a Trust Smart Home transmitter

Erasing the entire memory

A Press the connect button (8 seconds) until the LED indicator starts flashing rapidly. The reset mode will be active for 10 seconds and the LED indicator on the receiver will flash rapidly.
B While the reset mode is active, press the learn button again for 1 second to confirm that you want to delete the memory completely.
C To confirm, the wireless doorbell give 2 short beeps

Erasing the entire memory

Replacing the doorbell batteries

When the batteries are low, the LED on the doorbell will flash every 10 seconds. In this case, replace the batteries. If you replace the doorbell batteries, the paired transmitters will remain in its memory.

A Open the doorbell battery compartment by twisting the bottom open towards the open lock icon.
B Insert two 1.5V AA alkaline batteries (not included) as shown. Be sure to pay attention to the correct polarity of the batteries (place plus and minus on the right side).
C Place the bottom cover back on the doorbell.

Replacing the doorbell batteries

Make sure that the line on the bottom of the doorbell is in line with the open lock icon. Then turn the bottom side to the closed lock icon.

Changing the battery of the push button

A When the battery is low, the LED will light up for 2 sec and then blink 3 times after pressing the push button. Insert a flat screwdriver into the notch on the bottom of the push-button and slide the push-button off the back plate.
B Open the waterproof rubber to reveal the battery
C Remove the old battery and insert a new CR2032 battery into the recess of the battery holder. Make sure the + is pointing upwards.
C Close the waterproof rubber and place the push button back on the back plate.

Changing the battery of the push button

Combine the push button with the Internet
Control Station (ICS-2000) or Smart Bridge

Combine the push button with the Internet Control Station (ICS-2000) or Smart Bridge and also receive a push notification on your smartphone when the doorbell rings. For example, you can turn the wireless doorbell off at night and only receive a push notification when the push button is pressed.

Safety Instructions

Product support: www.trust.com/71275. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: 7.21 dBm. Radio transmission frequency range: 433,92 MHz

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.

Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.

Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.

Trust Electronics Ltd. declares that item number 71275/71275-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance

Trust International B.V. declares that item number 71275/71275-02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:
Model: ACDB-9000AC PORTABLE WIRELESS DOORBELL SET
Item number: 71275/71275-02
Intended use: Indoor

is in compliance with the essential requirements and other relevant provisions of the following directives:

ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)

The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com

Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change
without prior notice. Made in China.