THOR 28016T 37-80 Inch Full Motion Heavy Duty Wall Mount User Guide

THOR 28016T 37-80 Inch Full Motion Heavy Duty Wall Mount

Tools required

Components

Wall Mount & VESA Compatibility

• VESA is the standard adopted by most TV manufacturers
• for wall bracket mounting.
• There are 4 holes on the back of every flat screen TV and the space
•  between the holes is governed by the VESA standard.
• VESA comes in a range of sizes depending on the weight and size of the flat
•  screen TV; sizes 50 x 50mm, 75 x 75mm, 100 x 100mm, 200 x 100mm and so on… are standard. Not all flat screen TVs are compliant, contact the TV manufacturer for assistance if your TV does not appear to comply with
• VESA. To check if your TV or monitor is compliant, look at the rear of the display
•  there should be 4 screw/bolt holes in a square pattern or in larger displays a rectangular shape.
• Measure the distances marked (2) (horizontal) x (1) (vertical)
•  below in mm to find your VESA format.

SPECIFICATION

• TV Size range: 37-80″
• Maximum weight capacity: 70kg
• Mount function: Tilts +2/-15 Swivels +90/-90
• Wall to TV distance: 70-800mm
• Compatible with VESA sizes:
• 200 x 100, 200 x 200, 300 x 200, 300 x 300,
• 400 x 200, 400 x 300, 400 x 400, 600 x 400

WARNING

• We have not supplied wall fixings with this product. All walls differ in strength and thickness.
• Consult a qualified installer or seek advice from your local DIY/hardware store on purchasing suitable wall fixings to safely mount the bracket on the type of wall being used.
•  Check the components list and images to check there are no missing or defective parts.
•  Never exceed the Maximum

Weight Capacity.

•  Read these instructions carefully before installation. If in any doubt about safely installing this product, contact a professional installer for assistance.
•  This product was designed to be installed on wood stud walls and solid concrete/ brick walls. When fixing to walls screws/bolts should be fixed into bricks/stone not into mortar courses.
•  Make sure the wall will support the combined load of the equipment and hardware. Also check for hidden wiring or plumbing.
•  Make sure that the heads of the screws/ bolts you buy as wall fastenings are the correct size to hold the bracket securely in position
• Always ensure that all 4 bolts engage well into the VESA threaded apertures on the back of your TV; to at least a depth of 70% of the total depth of the aperture to ensure your TV is attached securely to the TV mount.
•  For larger/heavier TVs we recommend that you ask someone to assist you with lifting and positioning your TV.
•  This product is suitable for indoor use only.
•  Improper installation or use of this product can result in product failure, damage or personal injury.
•  This product contains small items that could cause choking if swallowed, so keep these items away from children and pets.
•  Appropriate safety equipment and proper tools must be used for installation. Always check manufacturer’s operating and safety instructions before using tools and other equipment.

INSTALLATION

•  Preparing Wall Fixings – Stud Walls

  • The wall bracket A is attached to the wall using four appropriate screws/bolts as shown in Fig.3. Make sure the screws/bolts are suitable for wood and large enough to support the weight of the TV and bracket (if in doubt ask for advice at your local DIY/hardware store and remember to make sure that the heads of the screws/bolts are the correct size to hold the bracket securely in position). Mark and drill four holes into the wood as close as possible to the centre of the upright (you can use a stud detector to find stud positions). To mark the holes, hold the bracket A to the wall, using a spirit level to make sure the bracket is level, and mark the centre of each hole, Drill the four holes and attach the bracket A to the wall using the appropriate screws/bolts.

•  Preparing Wall Fixings – Concrete/Brick Walls

  • The process is the same as for attaching to wood see Fig.6. You will however need to use suitable screws/bolts/wall plugs for the type of wall you are mounting onto and for the weight of your TV and bracket (if in doubt ask for advice at your local DIY/hardware store and remember to make sure that the heads of the screws/bolts are the correct size to hold the bracket securely in position). When fixing to walls, screws/bolts should be fixed into bricks/stone not into mortar courses.

•  Removing the VESA TV Bracket from the TV Mount

  •   * Loosen the nuts holding the VESA TV bracket to the TV mount. unscrew the bottom nuts.

  • Lift and remove the VESA bracket as shown, keep the bottom nuts in a safe place.

• Positioning the Back Plate of the TV Mount on the Wall Plate

  • Lift the TV mount and hook it onto the top rail of the wall plate align the holes of the back plate with the holes on the wall plate in position a , b or c as preferred.
    Select the centre position b . if you are unsure

• Fixing the Back Plate of the Mount to the Wall Plate

  • Slide the threaded retaining brackets D into the groove of the back plate top and bottom aligning the holes in the brackets with the holes in the wall plate and back plate as shown. Push the bolts E through the washers F , the wall plate and back plate and screw them into the threaded holes in the retaining brackets D using the Allen key H provided.

•  Attaching the Wall Plate Covers

  • Clip the top and bottom wall plate covers C onto the wall plate.

•  Attaching the VESA Bracket to the Television

  • Select the correct size bolts to fit the VESA holes for your TV I / J / K / L /M. Attach the VESA bracket to the back of the TV by lining up the VESA holes and using bolts I / J / K / L /M the washers N and the spacers O and or P (if the bolts are too long or the TV has a curved surface) to fix the TV securely to the adaptor brackets. N.B. Always ensure that all 4 bolts engage well into the VESA threaded apertures on the back of your TV

• Attaching the Television and VESA Bracket to the TV Mount

  • Engage the top nuts left on the VESA bracket with the slots on the TV mount and replace the bottom nuts then tighten all four nutsas shown.

• Adjusting the Tilt & Swivel

  • Press down the tilt lever to adjust the angle ot tilt. When the angle is as you want it pull up the tilt lever to lock the screen in position.

Technical Support:
www.philex.com/support

UK Distributor:

• Philex Electronic Ltd.,
• London Road, Bedford, MK42 0NX, U.K.
• EU Distributor: Philex Electronic Ireland Ltd.,
• Robwyn House, Corrintra, Castleblayney,
• Co. Monaghan, A75 YX76, Ireland.
• © Philex Electronic Ltd. 2021. Vb1.3

References

• Downloads – Philex Electronic Ltd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>