ethohome Electric Towel Warmer User Guide
- June 9, 2024
- ethohome
Table of Contents
ethohome Electric Towel Warmer
Instructions
- Please read the installation instructions carefully to properly set up your electric towel wormer.
- Make sure the installation is complete before us.
Installation: Wall Mounted
-
Secure wall-mount brackets to the electric heated towel rack with flat head screws. Choose your preferred place to fix the four corners of the electrically heated towel rail. Mark the four circles at each corner. Then find the center of the 4 marked circles to drill holes.
-
Insert the wall plug into the 4 holes as illustrated. Attach the other hall-wall-mounted brackets to the wall.
-
Adjust the retractable wall-mount brackets to their proper position.
Fix the retractable wall-mount brackets on the towel rack with flat head screws, and then buckle them to the fixed pieces on the wall.
Installation: Freestanding
Align the arc feet with the holes under the towel rack, and insert and screw the screws.
Operation
Plug the power cord into the appropriate electrical outlet.
After connecting to a suitable power supply, press the power switch to (I)
position, the power indicator will light up ond the heater start to work.
Press the power switch to (o) position, the power indicator light will turn
off along with the heater.
Cleaning
-
Before cleaning, please unplug the product and let it cool down.
-
Do not put the product, power cord or plug into the water.
Keep the cord dry. -
Cleon the surioce with o wet towel first and then dry it up with a soft cotton cloth.
PLEASE NOTE – DO NOT USE:
- Any sharp or rough objects against the surface of the towel rock, con cause damage to the surface of the product.
- Alcohol or solvents on plastic components, can cause damage to these parts.
This Towel Warmer is intended for use in bathrooms or laundry areas.
READ THE INSTRUCTIONS CAREFULLY BEFORE OPERATING
Specifications
Power Source: | 100-120VAC, 50/60Hz |
---|---|
Rating Power Input: | 100W |
Rated Voltage: | 100-120VAC, 50/60Hz, 100W |
IP Degree: | IPX4 |
Unit Size: | 90x52x36.5 (H x W x D) CM |
80x52x10 (H x W x D) CM
Important Safeguards
-
Keep the product unplugged when not in use.
Immediately stop using the product when the plug or cord is damaged.
The cord or plug should be replaced or repaired by professionals. -
Use this product strictly as described in this manual, in order to avoid the cause of fire, electric shock, or injury to persons.
-
For household use only.
Do not use outdoors. -
Never place the product into water, wet areas, or wet containers.
-
Children and elderly people with limited mobility, people with physical, sensory or mental impairments and a lack of experience and knowledge should use the product under the care or guidance by person responsible for their safety.
-
DO NOT wrap the product with towels, quilts when in use. Just lay the towels and quilts onto the product as pictured.
-
DO NOT place the power cord under the floor mats, the chute, or carpet to ovoid the danger of trip hazard.
-
DO NOT unplug the product by power cord, please hold the plug, not the cord.
-
DO NOT place or insert any objects into vents and exhaust ports, as it may cause on electric shock, fire, and/or damage the product.
-
DO NOT use it in areas where gasoline, points, or flammable liquids ore used or stored.
Warning
- This appliance is intended only for drying textiles washed in water.
- The towel rail is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
THE TOWEL WARMER IS ONLY ALLOWED TO BE INSTALLED AT A DISTANCE OF AT LEAST 23.6″ (600MM) FROM BASINS, BATHTUBS AND SHOWERS.
- Do not connect the plug into a socket-outlet which is exposed to liquid.
- This warmer is not intended for use with an extension cord.
- Plug the cord directly into an appropriate wall receptacle.
- The warmer must not be located immediately below a socket-outlet.
- To provide continued protection against risk of electric shock, connect to properly grounded outlets only.
- Do not immerse in water.
Maintenance
If the power cord is damaged, it must be replaced by o professional. DO NOT attempt to fix the issue yourself.