BOSCH AdvancedMulti 18 Home and Garden Multi Tool Instruction Manual
- June 9, 2024
- Bosch
Table of Contents
BOSCH AdvancedMulti 18 Home and Garden Multi Tool
Safety instructions
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cord-less) power tool.
Work area safety
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded sur-faces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suit-able for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is un-avoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
-
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal in-juries.
-
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in-jury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. -
Dress properly. Do not wear loose clothing or jewelers. Keep your hair and clothing away from moving parts. Loose clothes, jeweler or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust ex-traction and collection facilities, ensure these are connected and properly used. Use of dust collection can re-duce dust-related hazards.
-
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe in-jury within a fraction of a second.
Power tool use and care
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de-signed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or re-move the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into ac-count the working conditions and the work to be per-formed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Safety information for multifunction tools
- Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it un-stable and may lead to loss of control.
- Only use the power tool for dry sanding. Water entering a power tool will increase the risk of electric shock.
- Warning: Danger of fire! Avoid overheating the work-piece and the sander. Always empty the dust collector before taking a break from work. Sanding dust in the dust bag, microfilter, paper bag (or in the filter bag or vacuum cleaner filter) can spontaneously combust under certain conditions, for example if flying sparks are created when sanding metals. This risk is increased if the sanding dust is mixed with paint or polyurethane residue or with other chemical substances and if the workpiece is hot as a result of prolonged work.
- Keep hands away from the sawing area. Do not reach under the workpiece. Contact with the saw blade can lead to injuries.
- Clean the air vents on your power tool regularly. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
- Use suitable detectors to determine if there are hid-den supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to ex-plosion. Breaking water pipes causes property damage.
- Hold the power tool firmly with both hands and make sure you have a stable footing. The power tool can be more securely guided with both hands.
- When changing the application tool, wear protective gloves. Application tools can become hot when used for prolonged periods of time.
- Do not scrape any dampened materials (e.g. wallpaper) or on damp surfaces. Water entering a power tool increases the risk of electric shock.
- Do not treat the surface you will be working on with any fluids that contain solvents. Poisonous vapors may develop due to the materials heating up when being scraped.
- Take particular care when handling scrapers and blades. The application tools are very sharp. Danger of in-jury.
- In case of damage and improper use of the battery, vapors may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapors may irritate the respiratory system.
- Do not open the battery. There is a risk of short-circuiting.
- The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.
- Only use the battery with products from the manufacturer. This is the only way in which you can protect the battery against dangerous overload.
Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short- circuiting.
Product Description and Specifications
Read all the safety and general instructions. Failure to observe the safety and general in-structions may result in electric shock, fire and/or serious injury.
Please observe the illustrations at the beginning of this oper-ating manual.
Intended Use
The power tool is intended for sawing and cutting wood-based materials,
plastic, plasterboard, non-ferrous metals and mounting elements (e.g. nails,
clamps). It is also suit-able for working on soft wall tiles and for dry
sanding and scraping of small areas. It is ideal for working close to edges
and flush with surfaces.
Product Features
The numbering of the product features refers to the diagram of the power tool
on the graphics page.
- AutoClic lever for unlocking tools
- On/off switch
- Battery charge indicator
- Rechargeable battery)
- Battery release button)
- Orbital stroke rate preselection thumbwheel
- Ventilation slots
- Auxiliary handle (insulated gripping surface)
- Thread for auxiliary handle
- Tool holder
- 180° light band
- Plunge cut saw blade)
- Sanding plate)
- Sanding sheet)
- Depth stop)
- Segment saw blade
- Handle (insulated gripping surface)
- Extraction hose)
- Extraction outlet)
- Dust extraction)
- Clamping lever for dust extraction system)
- Dust extraction adapter)
a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Technical Data
- A) Limited performance at temperatures <0 °C
- B) The following chargers are not compatible with the PBA re-chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according to EN 62841‑2‑4.
Typically, the A-weighted noise level of the power tool is: Sound pressure
level 82 dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Working without the Auxiliary Handle
Vibration total values ah (triax vector sum) and uncertainty K determined
according to EN 62841‑2‑4 (sanding),
EN 62841‑2‑11 (sawing):
Sanding: ah=6 m/s2, K = 1,5 m/s2,
Cutting with plunge cut saw blade: ah = 16 m/s2, K = 1,5 m/s2,
Cutting with segmental saw blade: ah = 14 m/s2, K = 1,5 m/s2.
Working with the auxiliary handle
Vibration total values ah (triax vector sum) and uncertainty K determined
according to EN 62841‑2‑4 (sanding),
EN 62841‑2‑11 (sawing):
Sanding: ah = 6 m/s2, K = 1,5 m/s2,
Cutting with plunge cut saw blade: ah = 20 m/s2, K = 2,5 m/s2,
Cutting with segmental saw blade: ah = 16 m/s2, K = 1,5 m/s2.
The vibration level and noise emission value given in these instructions have
been measured in accordance with a standardized measuring procedure and may be
used to com-pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value represent the main
applications of the power tool. However, if the power tool is used for other
applications, with different application tools or is poorly maintained, the
vibration level and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool
is switched off or when it is running but not actually being used should also
be taken into account. This may significantly reduce vibration and noise
emissions over the total working period.
Implement additional safety measures to protect the operator from the effects
of vibration, such as servicing the power tool and application tools, keeping
their hands warm, and organizing workflows correctly.
Assembly
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
Battery Charging
- Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full battery
capacity, fully charge the battery in the charger before using your power tool
for the first time.
The lithium-ion battery can be charged at any time without reducing its
service life. Interrupting the charging process does not damage the battery.
The lithium-ion battery is protected against deep discharge by the “Electronic
Cell Protection (ECP)”. When the battery is discharged, the power tool is
switched off by means of a protective circuit: The application tool no longer
rotates.
- Do not continue to press the On/Off switch after the power tool has automatically switched off. The battery can be damaged.
To remove the battery (4), press the battery release button (5) and pull the battery to the rear and out of the power tool. Do not use force to do this.
Battery charge indicator
The battery charge indicator (3) indicates the remaining battery capacity or
an overload when the power tool is switched on.
If the battery charge indicator (3) flashes red, the power tool is
overloaded (see “Temperature-dependent overload protection”, page 24).
Changing the tool
- Wear protective gloves when changing tools. There is a risk of injury when touching the application tools.
Selecting an Application Tool
Please observe the application tools intended for your power tool.
The following table shows examples of application tools. You can find additional application tools in Bosch’s extensive range of accessories.
Fitting/changing the application tool (AutoClic) (see figures A–B)
Remove the application tool if one has already been fitted. To do so, open the
AutoClic lever (1) all the way. The application tool/accessory will be
ejected.
Place the required application tool (e.g. plunge cut saw blade (12)) on a
level surface so that the depressed center is face down (see figure on the
graphics page; you should be able to read the text on the application tool
from above). Turn the application tool to a position which is convenient for
the job at hand. Press the power tool onto the application tool at the
required angle until it audibly engages.
- Check that the application tool is seated securely. Application tools that are attached incorrectly or are not securely fixed in place may come loose during operation, thereby putting you at risk.
Fitting and Adjusting the Depth Stop
The depth stop (15) can be used when working with segment saw blades.
Remove the application tool if one has already been fitted.
Slide the depth stop (15) over the tool holder (10) and onto the collar of the
power tool as far as it will go, with the la-belled side facing upwards.
The depth stop is intended for the following cutting depths:
-
With segment saw blades ACZ 85 .. with a diameter of 85 mm: Cutting depths 8 mm, 10 mm, 12 mm and
14 mm (information on the depth stop in a larger font size and without brackets). -
With segment saw blades ACZ 100 .. with a diameter of 100 mm: Cutting depths 14 mm, 16 mm, 18 mm and 20 mm (information on the depth stop in a smaller font size and in brackets).
Insert the appropriate segment saw blade for the desired cutting depth. Slide
the depth stop (15) from the tool holder (10) in the direction of the
application tool until you can rotate it freely. Rotate the depth stop (15) so
that the desired cutting depth is above the section of the saw blade that will
be used to saw. Slide the depth stop (15) onto the collar of the power tool
once again as far as it will go.
Remove the depth stop (15) for all other cutting depths and for working with
other application tools. To do this, remove the application tool and pull the
depth stop away from the collar.
Fitting the Auxiliary Handle (accessory)
The low-vibration auxiliary handle enables the tool to be used safely and more
comfortably.
Screw the auxiliary handle into the thread (9) on the left or right of the
machine head depending on how you are working.
- Do not continue to use the power tool if the auxiliary handle is damaged. Do not make any alterations to the auxiliary handle.
Choosing the Sanding Sheet
Different sanding sheets are available, depending on the material you are
working with and the required surface removal rate:
Attaching/changing the sanding sheet on the sanding plate
The sanding plate (13) is fitted with a hook-and-loop fastening, allowing
sanding sheets with a hook-and-loop backing to be secured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (13) before fitting the
sanding sheet (14) to facilitate maximum adhesion.
Position the sanding sheet (14) so that it is flush with one side of the
sanding plate (13), then place the sanding sheet on the sanding plate and
press it on firmly.
To ensure optimum dust extraction, make sure that the punched holes in the
sanding sheet are aligned with the drilled holes in the sanding plate.
To remove the sanding sheet (14), take hold of it by an edge and pull it away
from the sanding plate (13).
You can use all sanding sheets, polishing and cleaning fleeces from the Delta
93 mm series in the Bosch range of accessories.
Sanding accessories such as fleece/polishing felt are attached to the sanding
plate in the same way.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of wood, minerals and
metal can be harmful to human health. Touching or breathing in this dust can
trigger allergic reactions and/or cause respiratory illnesses in the user or
in people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as carcinogenic,
especially in conjunction with wood treatment additives (chromate, wood
preservative). Materials containing asbestos may only be machined by
specialists.
- Use a dust extraction system that is suitable for the material wherever possible.
- Provide good ventilation at the workplace.
- It is advisable to wear a P2 filter class breathing mask. The regulations on the material being machined that apply in the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can easily ignite.
Connecting the dust extraction system (see figure C)
The dust extraction system (20) is only designed for use with the sanding
plate (13); it serves no purpose when used together with other application
tools.
Always connect a dust extraction system for sanding. Remove the application
tool and the depth stop (15) for fit-ting the dust extraction system (20)
(accessory).
Slide the dust extraction system (20) as far as it will go over the tool
holder (10) onto the collar of the power tool. Turn the dust extraction system
to the required position (not directly under the power tool). Push the
clamping lever (21) shut to fix the dust extraction system in position.
Push the dust extraction adapter (22) (accessory) onto an extraction hose (18)
(accessory) until you hear it click into place. Connect the dust extraction
adapter (22) to the ex-traction outlet (19) and the extraction hose (18) to a
dust extractor (accessory).
You will find an overview of how to connect various dust ex-tractors at the
end of these operating instructions.
The dust extractor must be suitable for the material being worked.
When extracting dry dust that is especially detrimental to health or
carcinogenic, use a special dust extractor.
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can lead to
malfunctions or damage to the power tool.
Insert the charged battery (4) into the base of the power tool until you feel
it engage and it is securely locked in place.
Switching On/Off
- Make sure that you are able to press the On/Off switch without releasing the handle.
To switch on the power tool, slide the on/off switch (2) for-ward so that “I”
appears on the switch.
The electronic soft start limits the torque when the power tool is switched on
and increases the service life of the motor.
The Constant Electronic keeps the orbital stroke rate at no load and under
load virtually consistent, guaranteeing uniform performance.
To switch off the power tool, slide the on/off switch (2) backwards so that
“0” appears on the switch.
Note: If the power tool shuts down automatically because the battery is flat
or overheated, switch the power tool off using the on/off switch (2).
Charge the battery or let it cool down before switching the power tool on
again. Failure to do so can damage the battery.
The 180° light band (11) improves visibility in the immediate work area. It is
automatically switched on and off with the power tool.
Preselecting the orbital stroke rate
You can even preselect the required orbital stroke rate during operation using
the orbital stroke rate preselection thumbwheel (6).
The required orbital stroke rate is dependent on the material and the work
conditions and can be determined using practical tests.
Orbital stroke rate level “6” is recommended for sawing, cut-ting and sanding
harder materials, such as wood or metal; orbital stroke rate level “4” is
recommended for softer materials, such as plastic.
Working Advice
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
- Always wait until the power tool has come to a complete stop before placing it down.
Note: Do not keep the ventilation slots (7) on the power tool closed when working as this will reduce the service life of the power tool.
Operating principle
The oscillating drive causes the application tool to oscillate back and forth
by 2.8° up to 20000 times per minute. This enables precise work in the
tightest of spaces.
Use a consistent, low contact pressure when performing work;
otherwise, the performance will be impaired and the application tool may jam.
While working, move the power tool back and forth to prevent the application tool overheating and jamming.
Sawing
- Use only undamaged saw blades that are in perfect condition. Bent or dull saw blades can break, negatively influence the cut, or lead to kickback.
- When sawing lightweight materials, take into account the statutory provisions and recommendations of the material manufacturers.
- Plunge cuts may only be applied to soft materials, such as wood, gypsum board, etc.
Before using HCS saw blades to saw into wood, chipboard, building materials, etc., check these saw blades for foreign objects, such as nails, screws, etc. Remove the foreign ob-jects as required or use bi-metal saw blades.
Cutting
Note: When cutting wall tiles, please bear in mind that the application tools
are subject to high wear if used for extended periods.
Sanding
The material removal rate and sanding result are primarily determined by the
choice of sanding sheet, the preselected orbital stroke rate level and the
contact pressure.
Only immaculate sanding sheets achieve good sanding performance and make the
power tool last longer.
Be sure to apply consistent contact pressure in order to in-crease the
lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to increased sanding
performance, rather it will cause more severe wear of the power tool and of
the sanding sheet.
To sand corners, edges and hard-to-reach areas accurately, you can also work
with the tips alone or with an edge of the sanding plate.
The sanding sheet may heat up significantly when used to sand specific points
rather than entire surfaces. Reduce the orbital stroke rate and contact
pressure and allow the sanding sheet to cool down at regular intervals.
Do not use a sanding sheet for other materials after it has been used to work
on metal.
Use only original Bosch-sanding accessories.
Always connect a dust extraction system for sanding.
Scraping
Select a high orbital stroke rate level for scraping.
Work on a soft surface (e.g. wood) at a flat angle and with low contact
pressure. Failure to do so may cause the scraper to cut into the surface
underneath.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-loaded. In the
event of excessive load or temperatures out-side of the permitted battery
temperature range, the power tool switches off. Switch the power tool off,
allow the battery to cool down, then switch the power tool back on.
Recommendations for Optimal Handling of the Battery Protect the battery
against moisture and water.
Only store the battery within a temperature range of −20 to 50 °C. Do not
leave the battery in your car in the summer, for example.
Occasionally clean the ventilation slots on the battery using a soft brush
that is clean and dry.
A significantly reduced operating time after charging indicates that the
battery has deteriorated and must be replaced. Follow the instructions on
correct disposal.
Maintenance and Service
Maintenance and Cleaning
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
- To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.
Regularly clean Riff application tools (accessories) using a wire brush.
After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and
repair of your product as well as spare parts. You can find explosion drawings
and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions
about our products and their accessories.
In all correspondence and spare parts orders, please always include the
10‑digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts
or arrange the collection of a product in need of servicing or repair. Tel.
Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legislation on the
transport of dangerous goods. The user can transport the batteries by road
without further requirements.
When shipping by third parties (e.g.: by air transport or for-warding agency),
special requirements on packaging and la-belling must be observed. For
preparation of the item being shipped, consulting an expert for hazardous
material is required.
Dispatch battery packs only when the housing is undam-aged. Tape or mask off
open contacts and pack up the battery in such a manner that it cannot move
around in the packaging. Please also observe the possibility of more de-tailed
national regulations.
Disposal
The power tool, accessories and packaging should be re-cycled in an
environmentally friendly manner.
Do not dispose of power tools along with household waste.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste Electrical and
Electronic Equipment and its implementation into national law, power tools
that are no longer usable must be collected separately and disposed of in an
environment-ally friendly manner.
If disposed incorrectly, waste electrical and electronic equipment may have
harmful effects on the environment and human health, due to the potential
presence of hazardous substances.
Only for United Kingdom:
According to Waste Electrical and Electronic Equipment Regulations 2013
(2013/3113), power tools that are no longer usable must be collected
separately and disposed of in an environmentally friendly manner.
References
- Invented for life | Bosch Global
- Skånevik Ølen Kraftlag AS
- Bosch Power Tools | Bosch Power Tools
- Location selection | Bosch Power Tools
- Service worldwide
- Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
- Bosch el-værktøj | Bosch el-værktøj
- Bosch-sähkötyökalut | Bosch-sähkötyökalut
- Outillage électroportatif Bosch | Outillage électroportatif Bosch
- Home | Bosch Power Tools
- Invented for life | Bosch Global
- Ana Sayfa | Bosch Türkiye
- herramientasbosch.net