maytronics 8152200 Dolphin Wave 100 Small-Mid Commercial Pool Cleaner User Manual

maytronics 8152200 Dolphin Wave 100 Small-Mid Commercial Pool Cleaner User Manual

INTRODUCTION

Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions and  all-surface climbing brush enhance maximum pool hygiene. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting performance and easy maintenance.

SPECIFICATIONS

• Motor protection: IP 68
• Minimum depth: 0.4 m (1.33 ft)
• Maximum depth: 5 m (16.4 ft)

WARNINGS AND CAUTIONS

Warnings

• Use the originally supplied power supply only
• Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI)
• Keep the power supply out of standing water
• Position the power supply at least 3.5 m (12 ft) away from the edge  of the pool
• Do not enter the pool while the pool cleaner is working
• Unplug the power supply before servicing
• Keep the Robotic Pool Cleaner out of the reach of children or persons  with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

Cautions

When not in use store the Pool Cleaner on the Caddy in a shaded area. Use the Pool Cleaner in the following water conditions only:

POOL CLEANER PARTS

Dolphin WAVE 100

Combined Brush
All surface climbing brush ideal for most pool surfaces

Wonder Brush
For smooth ceramics (optional)

Bottom lid and filter Bag

Filter bag options: Fine – factory default Ultra fine – extra Disposable filter bag x 5

Caddy

Remote Control Unit

Power Supply Unit

USING THE POOL CLEANER

Set Up

Before using the Pool Cleaner for the first time perform the following steps.

nwind the cable and stretch it out completely so that it has no kinks.

Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined upwith the groove in the socket on the power supply and turning clockwise (2).

Change diagonal handle position for water line sideway movement. To adjust the handle angle:

• A. Press the latch down and hold
  it in position.

• B. Move the handle to the desired position and release the latch to hold the handle in place.

Normal advance More efficient cleaning action on water-line.

Fast advance Fast speed – for faster but less efficient cleaning action on water-line.

Putting the Pool Cleaner into the poo

If the foam climbing rings on the brushes are dry soak them in water until soft.

Shake the robot from side to side or turn it upside down to release trapped air. Let it sink to the pool floor.

Turn the power supply ON.

Turn OFF and unplug the power supply.

Using the floating cable, bring the Pool Cleaner to the pool’s edge.

DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.

Maintenance

Clean the filter bag with a hose. Periodically clean the brushes with a hose. It is recommended to periodically wash the filter bag in a washing machine. Use gentle cycle program.

Cleaning the impeller
Unplug the power supply

If you notice debris trapped in the impeller, open the impeller and remove the debris

Cable

To remove the kinks, stretch the cable out completely and let it sit for at least a day in the sun.

Off-season storage

If the pool cleaner will not be in use for an extended period, perform the following storage steps:

• Make sure that no water is left in the pool cleaner
• Thoroughly clean the filter bag and insert in place
• Roll up the cable so that it has no kinks and place on the Caddy
• Store the pool cleaner upright on the Caddy in a protected area out of direct sun/rain/frost at a temperature of between 5 °C – 45 °C (41 °F – 113 °F)

POWER SUPPLY

<30 VDC; IP 54 Digital “Switch-Mode” Power Supply with full filter bag and delay indicator.

• Input – 100 VAC – 250 VAC
• 50 Hz – 60 Hz
• 180 W
• Output – <30 VDC
• IP 54

Full filter bag indicator and Reset button

The power supply is equipped with a filter bag status indicator. The red LED indicates two filter conditions.

• When blinking – The filter is partially blocked.
• When lighted – The filter is blocked and must be emptied and cleaned. If the LED does not turn off after the filter bag had been emptied and cleaned, press the RESET button while the robot is working.

Delay indicator
The power supply is equipped with a Delay indicator that indicates if the Delay option is activated (through the remote control unit).

REMOTE CONTROL UNI

The Control Panel

The remote control unit (RCU) offers two operation modes – Automatic mode and manual direction control mode. In automatic mode, the cleaning parameters can be changed. In manual direction mode, the robot’s motion can be controlled manually

Manual Direction Control Mode

1. Press the On/Off button once. The remote control will start in
   manual direction control mode.

2. Use the direction control arrows (see right) to control the
   movement of the robot around the poo

Exiting Manual Direction Control Mode and setting the Automatic Mode

1. To exit the manual direction control mode, press the Manual/Automatic select button once only.
2. The digital screen will light up and three rows of function icons will be displayed in default mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>