BLACKMONT BLM-CCPRO40L Compressor Freezer User Manual

BLACKMONT BLM-CCPRO40L Compressor Freezer

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before using for the first time and keep this user manual for future reference. Pay special attention to the safety instructions. If you have any questions or comments about the product, contact the customer line. @ www.alza.cz/kontakt
[TEL] +420 255 340 111
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 7, www.alza.cz

SAFETY INSTRUCTIONS

• This appliance is intended for use by children 8 years of age and older and persons with reduced physical, sensory or mental capabilities and lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the appliance in a safe manner and understand the potential hazards.
• Children must not play with the device.
• Cleaning and user maintenance must not be performed by children without supervision.
• Children aged 3 to 8 can insert and remove food into and out of the appliance.
• This appliance is not intended for permanent connection to a water pipe or for connection by a hose system.
• This appliance is not intended to be built-in or attached. It is designed to be free-standing.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a dangerous situation.
• Always place the appliance on a flat, solid and dry surface.
• Unplug the appliance when cleaning it, moving it when not in use or leaving it unattended.
• This appliance is suitable for use at home, in a car, in a recreational vehicle, while camping.
• This appliance can be connected to more than one power source.
• This appliance must not be exposed to rain.
• Follow the instructions in this manual when installing, operating, servicing and handling the appliance.
• WARNING: The ventilation openings in the appliance housing or in its construction must be kept free.
• WARNING: Do not use mechanical devices or means other than those recommended by the manufacturer to speed up the defrosting process.
• WARNING: Do not damage the cooling circuit.
• WARNING: Do not use electrical appliances in the food storage area unless they are the types recommended by the manufacturer.
• Do not store explosive substances, such as flammable propellant sprays, in this appliance.
• This appliance is intended for use in the home and similar spaces, such as:
  • Kitchenettes in shops, offices and other workplaces;
  • Appliances used by guests in hotels, motels and other residential establishments;
  • Appliances used in Bed & Breakfast establishments;
  • Appliance used in catering and similar non-commercial environments.
• Follow the instructions in this manual to ensure safe food storage.
• Store only packaged food or food stored in food storage containers in the appliance.
• The following recommendations should be followed to prevent food contamination:
  • Keeping the lid open for a long time can cause a significant increase in the temperature inside the appliance.
  • Regularly clean surfaces that may come into contact with food and accessible drainage systems.
  • Store raw meat and fish in the refrigerator in suitable containers so that they do not come into contact with or drip on other foods.
  • If the appliance is to remain empty for a long time, switch it off, defrost it, clean it, dry it and leave the lid open to prevent the formation of mold inside the appliance.
• WARNING: When placing the appliance, make sure that the power cord is not caught or damaged.
• WARNING : Do not place multiple portable outlets or portable extension cords on the back of the appliance.
• The appliance must be installed on a ship by a qualified person.
• Always make sure that the voltage of the outlet to which the appliance is to be connected corresponds to the voltage indicated on the type plate of the adapter.
• Make sure that the appliance is horizontal during transport. Never tilt it.
• Handle the appliance carefully.
• This appliance is intended for short-term food storage. It is not suitable for freezing food or for long-term storage.
• This appliance is not intended for heating cold food, but for maintaining the temperature of hot food.
• To ensure proper operation of the appliance, ensure sufficient free space around it (min. 10 cm on the sides).
• Make sure that the appliance is placed at a sufficient distance from heat sources. Do not expose the appliance to direct sunlight.
• Check the condition of the car battery to avoid discharging it if the car battery allows you to supply the appliance from a 12 V / 24 V outlets without the engine running.
• Prevent the appliance from tipping or falling.
• Do not used the appliance in places with high humidity or dust.
• Do not touch the adapter plug with wet hands.
• Always unplug the power cord from the outlet by holding the plug. Neber unplug appliances by pulling on the power cord.

TECHNICAL PARAMETERS

AC 100–240 V ~ 50/60 Hz

Energy consumption| DC 12/24 V 4,2 – 2,2 A AC 100–240 V ~ 0,8 – 0,4 A
Cooling capacity| -22 °C up to + 12 °C
Category| 1
Energy efficiency class| E| E| E
Volume| 40 l| 50 l| 58 l
Climate class| N
Ambient temperature| +16 °C up to + 32 °C
Dimensions (w x h x d) in mm| 713,8 x 449 x 446| 714 x 452.4 x 468.5| 714 x 453.4 x 523.5
Weight| 20 kg| 21.5 kg| 23 kg

NOTE
If the ambient temperature is higher than +32 ° C (+90 ° F), the minimum cooling temperature cannot be reached
Tests/certificates:

The cooling circuit contains R-1234yf.

PACKAGE CONTENTS

INTENDED USE

The freezer is suitable for cooling and freezing food. The appliance is also suitable for use on boats. The appliance is designed for power supply from 12 V — or 24 V — on ships or in vehicles (e.g. from a cigarette lighter), caravans and from the 220-240 V AC power supply.

WARNING!! Health risk!
Make sure that the cooling capacity of the appliance is suitable for storing the food or medicine you want to keep cool.

FUNCTION DESCRIPTION

The appliance can cool the products, keep them cool and also freeze them. The low-maintenance refrigeration circuit with compressor offers cooling. Massive insulation and a powerful compressor ensure efficient and fast cooling.
It is a portable appliance.
The appliance withstands a constant temperature of 30 °, for example when used on a boat

FUNCTIONS

• Power supply with priority circuit for connection to the AC mains.
• Three-level battery monitor to protect the vehicle battery.
• Temperature display in ° C and ° F.
• Automatic shutoff in case of low battery.
• Temperature setting: using two buttons in steps of 1 ° C (2 ° F)
• Folding handles for carrying.
• Emergency switch (if equipped).
• Removable wire basket.

CONTROL AND DISPLAY ELEMENTS

Lid latch, Fig. 2

Control panel, fig. 3

two seconds.
2| POWER| Status indicator
 |  | The LED indicator light is green: the compressor is running.
 |  | The LED indicator light is orange: the compressor is not running
 |  | The LED flashes orange: the display automatically shuts off when the battery is low.
3| ERROR| LED flashes red: the appliance is switched on but not ready for operation.
4| SET| Input mode selection

– Temperature setting

– Display of Celsius or Fahrenheit degrees

– Battery monitor setting

5| –| Display, information display
6| UP+| Press to increase the value.
7| DOWN-| Press to lower the value

Connection sockets, Fig. 4

Emergency switch (if equipped), Fig. 5

OPERATION

BEFORE FIRST USE
NOTE
Before using your new appliance, you must clean the inside and outside with a damp cloth for hygienic reasons (see also section “Cleaning and maintenance”).

The lid can be removed or opened from one side or the other, 2 ways to open – left or right. Setting the temperature units

The temperature display can be set to Celsius and Fahrenheit as follows:

• Turn on the appliance
• Press the “SET” button twice (obr. 3 4).
• Press “UP+ (fig. 3 6) “or “DOWN – (fig. 3 7) “to select Celsius or Fahrenheit degrees.
• The selected temperature units will then appe3 ar on the display for a few seconds. The display flashes several times before it displays the current temperature.

ENERGY SAVING TIPS

• Choose a well-ventilated place that is protected from direct sunlight.
• Allow warm food to cool before placing it the appliance.
• Do not open the appliance more often than necessary.
• Do not leave the appliance open for longer than necessary.
• Defrost the appliance after frost has formed.
• Avoid excessively low temperatures.

CONNECTING THE APPLIANCE

Battery connection (vehicle or boat) You can supply the appliance from 12 V or 24 V.

Note! Risk of damage!

Disconnect the refrigerator and other appliances from the battery before connecting the battery to the quick charger. Overvoltage can damage the electronics of the appliance. For safety reasons, the appliance is equipped with an electronic system to prevent polarity reversal. This protects the appliance against short circuits when connected to the battery.

• Connect the 12/24 V power cable to the DC connector of the appliance (fig. 1 2) and also to the 12 V or 24 V cigarette lighter.

Connection to 220-240 V AC electric outlet (e.g. at home or office) DANGER! Risk of electric shock!

• Never handle connectors or switches with wet hands or when standing on a wet surface.

• If you are using the appliance on a boat with a 220-240 V supply, you must install a residual current circuit breaker between the 220-240 V AC power supply and the appliance. Ask an experienced technician for help.
  The appliance has an integrated multi-voltage supply with a priority circuit that automatically switches the appliance to electrical outlet power supply if you connect the appliance to a 220-240 V AC outlet, even if a 12/24 V connecting cable is still connected.

• Connect the 220-240 V connecting cable (fig. 1 3) to the AV outlet of the appliance and connect the other end to the 220-240 V AC power outlet.

USING BATTERY MONITOR
The appliance is equipped with a multi-level battery monitor that protects your vehicle’s battery from being over-discharged when the appliance is connected to a 12/24 V supply.
If you use the appliance when the vehicle engine is switched off, the appliance switches off automatically when the supply voltage falls below the set level. The appliance switches on again when the battery is being charged and reaches the starting voltage level.

NOTE! Risk of damage!
When the appliance is switched off thanks to the battery monitor, the battery is no longer charges fully. Avoid restarting or using other appliances without longer charging stages. Make sure the battery is charged!

In “HIGH” mode, the battery monitor responds faster than in “LOW” and “MED” mode (see the following table).

The battery monitor mode can be set as follows:

• Turn on the appliance

• Press the “SET“ (obr. 3 4) button three times.

• Press “UP+ (fig. 3 6)“ or “DOWN – (fig. 3 7)“ to select the battery monitor mode.

• The digital display shows the following:
  Lo (LOW), Me (MED), Hi (HIGH)

• The selected mode will then appear on the display for a few seconds. The display flashes several times before returning to the current temperature display.

NOTE
If the appliance is equipped with a starter battery, select the battery monitor mode “HIGH”. If the appliance is connected to a battery, the battery monitor mode “LOW” will suffice.

USING THE APPLIANCE
NOTE! Danger of overheating!
Ensure adequate ventilation at all times so that the heat which is generated can escape well. Make sure the vents are not covered. Make sure that the appliance is far enough away from walls and other objects that may hinder air circulation.

• Place the appliance on a solid surface.
  Make sure that the vents are not covered and that air can escape.
  NOTE
  Place the appliance as shown (fig. 1 1.). If you use the box in different positions, you may damage it.

• Close the appliance – see “Connecting the appliance”.
  NOTE! Risk of excessively low temperature!
  Only put objects that can be cooled at the selected temperature into the appliance.

• Press the “ON / OFF” button (fig. 3 1) for one or two seconds.

• LED lights up (fig. 3 2).

• The display (fig. 3 5) turns on and displays the current cooling temperature.

NOTE
Displayed temperature:
The displayed temperature is in the middle of the large cooling space.

All models:
The temperature varies in different parts of the space and may deviate slightly from the displayed one. The appliance starts cooling the interior.

NOTE
When you run the appliance on battery power, the display automatically switches off when the battery voltage is low. LED flashes orange.

Appliance lid latch

• Close the lid.
• Press on the locks (fig. 2 1) down, until they lock in place.

SETTING THE TEMPERATURE

• Press the “SET” button once (fig. 3 4).
• Press “UP + (fig. 3 6)“ and “DOWN – (fig. 3 7)“ to set the cooling temperature.
• The cooling temperature appears on the display for a few seconds. The display flashes several times, then the current temperature is displayed again.

USING THE EMERGENCY SWITCH (IF EQUIPPED)
The emergency switch (fig. 5 1) is located under the control panel. During normal operation, the switch is in the “NORMAL USE” position.

• If an electronic control defect occurs, move the switch to the “EMERGENCY OVERRIDE” position.

NOTE
If the switch is in the “EMERGENCY OVERRIDE” position, the appliance freezes at full power.

TURNING OFF THE APPLIANCE

• Empty the appliance

• Turn it off.

• Disconnect the connecting cable.
  If you will not be using the appliance for a long time:

• Leave the lid slightly open. This will prevent the formation of odors.

DEFROSTING THE APPLIANCE
Moisture can form ice inside the appliance or in the evaporator. This lowers the cooling capacity. To prevent this, defrost the appliance at the opportune time.

NOTE! Risk of damage!
Never use hard or sharp objects to defrost or free frozen food. To defrost the appliance, proceed as follows:

• Remove the content of the appliance.
• If necessary, store them in another refrigeration appliance to keep them cool.
• Turn off the appliance.
• Leave the lid open.
• Wipe off melted water.

FUSE REPLACEMENT
DANGER! Risk of electric shock!
Disconnect the connecting cable prior to fuse replacement.

• Disconnect the connecting cable.
• Pull out the fuse (fig. 4 2) using a screwdriver.
• Replace the defective fuse with a new one with the same parameters.
• Push the fuse back into place.

REPLACING THE FUSE IN THE PLUG (12/24 V)

• Turn the lid counterclockwise (fig. 7 1) and remove it with the pin (fig. 7 2) from the plug.
• Insert a new fuse (fig. 7 3) with the same parameters.
• Assemble the plug in reverse order.

PCB LIGHTING REPLACEMENT

• Remove the transparent cover using a screwdriver (fig. 8 1).
• Remove the PCB mounting screws (fig. 8l 2).
• Disconnect the connector from PCB (fig. 8 3).
• Replace the defective PCB lighting with a new one.
• Install the PCB in reverse order.
• Replace the transparent cover

CLEANING AND MAINTENANCE

WARNING!
Always unplug the appliance before cleaning and maintenance.

NOTE! Risk of damage

• Never clean the appliance under running water or in the dishwasher.
• Do not use harsh or hard cleaning agents as these may damage the appliance.
• Occasionally clean the inside and outside of the appliance with a damp cloth.

WARRANTY

The warranty conditions according to the country of sale apply. If the appliance is defective, contact the dealer in your country. Attach the following documents when claiming the warranty:

• A copy of the proof of purchase with the date of purchase.
• The cause of the claim and a description of the defect.

TROUBLESHOOTING

ignition must be on to power the cigarette lighter.
There is no voltage in the AC outlet.| Try to use another outlet.
Defective fuse of the appliance.| Replace the fuse, see
“Fuse replacement”.| Move the appliance away from the wall or a foreign object.
The appliance is not cooling (the plug is in, the “POWER” LED is lit).| Defective compressor.| This can only be repaired by an authorized service center.
The appliance is not cooling (plug is connected, “POWER” LED flashes orange, display does not light up).| The battery voltage is low.| Test the battery and charge it if necessary.
If you are using

a 12/24-V outlet (cigarette lighter): The ignition is on and the appliance does not work, the LED is off. Disconnect

the plug from the outlet and perform the following checks

| The cigarette lighter is dirty. This causes poor electrical contact.| If the appliance plug heats up in a cigarette lighter, you must clean the plug or outlet or assemble the plug correctly.
---|---|---
Blown fuse of the 12/24 V plug.| Replace the fuse (10 A) in the 12/24 V plug, see “Replacing the plug fuse (12/24 V)”.
Vehicle fuse is blown.| Replace the vehicle’s 12/24 V fuse (usually 15 A). See the operating manual for your vehicle.
The display shows an error message (eg “Err1”) and the appliance is not cooling.| The appliance switches off due to an internal defect,| This can only be repaired by an authorized service center.

Protection class III equipment: the equipment is designed for low safe voltage. Protection against electric shock is provided by a low safe voltage.

WARRANTY CONDITIONS

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must present the original proof of purchase with the original date of purchase. Copies of proof of purchase of the product, altered, supplemented, without the original data or otherwise damaged proof of purchase of the product will not be considered as proof of purchase of the claimed product.

The following is considered a breach of warranty, for which the claim may not be accepted:

• Use of the product for purposes other than those for which it is intended or failure to follow the instructions for maintenance, operation and service of the product.
• Damage to the product due to a natural disaster, intervention by an unauthorized person or mechanical fault of the buyer (e.g. during transport, cleaning by inappropriate means, etc.).
• Natural wear and tear of consumables or components during use (such as batteries, etc.).
• Exposure to adverse external influences such as sunlight and other radiation or electromagnetic fields, intrusion of liquids, intrusion of objects, overvoltage into the mains, electrostatic discharge voltage (including lightning), defective power supply or input voltage and unreasonable polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone had made design modifications or adjustments to change or extend the functions of the product compared to the purchased design or using non-genuine components.

EC DECLARATION OF CONFORMITY

Identification of the manufacturer/importer’s authorized representative:
Manufacturer: Alza.cz, a. s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
Company ID: 27082440

Subject of the declaration:
Name: Car refrigerator
Model/Type: BLM-CCPRO40L / ECF-40; BLM-CCPRO50L / ECF-50; BLM-CCPRO58L / ECF-60
The above product has been tested in accordance with the standard (s) used to demonstrate compliance with the essential requirements set out in the Directive (s):
Directive No. (EU) 2014/30 / EU, Directive No. (EU) 2014/35 / EU, Directive (EU) 2019/2019, Directive No. (EU) 2011/65 / EU as amended 2015/863 / EU, Regulation (EC) No 19 35/2004.

Reference to harmonised standards:
EN 60335-1:2012+A11+A13+A1+A14+A2
EN 60335-2-24:2010+A1+A2
EN 62233:2008
AfPS GS 2019:01 PAK
EN 55014-1:2017+A11 EN 55014-2:2015
EN IEC 61000-3-2:2019 EN 61000-3-3:2013+A1

Technical documentation is stored at:
Alza.cz, a. s.
Jankovcova 1522/53, Holešovice, 170 00 Prague 7
The year of manufacture of the machine and the serial number are indicated on the machine.

Ing. Jan Melena
Business Development Manager
Sales and Purchasing; Private Labels

Co. Reg. No. 27082440
Alza.cz, a. s., Jankovcova 1522/53, 170 00 Prague 7, Czech Republic © 2022 Alza.cz, a. s. All Rights Reserved.

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz
• Alza | Alzashop.com
• Alza.cz

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>