WAGNER W-Life E-Table Height Adjustable Desk Instruction Manual
- June 9, 2024
- Wagner
Table of Contents
W-Life E-Table Height Adjustable Desk
Instruction Manual
W-Life E-Table Height Adjustable Desk
LIST OF PARTS
- 2x table feet
- 2x table legs
- 2x crossbars
- 2x side parts
- 1x tabletop
Screwdriver required
All other screws included in the assembly set are not required. It is not
possible to remove the superfluous screws prematurely. Before assembly Please
check the completeness of all parts. We recommend mounting on a material that
is gentle on the undergound. At each assembly step. first screw in all screws
1-2 turns. align the component and only then screw it on tight.
Keep small parts, packaging bags and foils due to danger of suffocation
and possible ingestion away from babies and infants.
In case of damage or defects to your table. please contact your Dealer or our
custo-rner servi.:
kundenservice@topstar.de. Please document
your request with pictu-res and/or a short description.
If you have any questions, please contact our customer service
kundenservice@topstar.de **Initial
setup: The W X Table is now ready for use. Please refer to our Quick Start
Guide on page 23 and the official instructions for use and care on the
following pages.
** Powersupply cable is freely movable in the entire adjustment range of
the cable
Manual reset / first start-up
Perform a reset by simultaneously holding the up and down buttons pressed for
at least 8 seconds. Let go, and then press downbutton. Desk will slowly move
downwards. The reset is complete when the desk has stopped at the lowest
point.
Follow these instructions when adjusting the table height:
- Ensure that there are no objects in the table height adjustment area.
- To move the desk up or down, press up or down.
Press the Up key until the desired table height is reached.
Press the down key until the desired table height is reached.
Saving of preferred standing and sitting position / end positions
Press both buttons three times (with an interval of 0.5-1 seco. between them).
Then press -up” or “down” to adjust the position (0.5-1 seco.). The same
applies to your second stored setting. To delete the memory positions, perform
a reset.
W X Table is an electromechanically height-adjustable sitting/standing table
with control switch for height adjustment up and down.
This device can be used by children aged 8 and over. Persons with limited phy-
sical, sensory or mental abilities or lack of experience and knowledge should
be supervised or instructed on the safe use of the device and should
understand the dangers involved. Children should not play with the device.
Cleaning and maintenance of the appliance must not be carried out by children
without super-vision.
Recommendations and parameters:
Sound level: < 50 dB(A)
Interval for height adjustment: 56,9 – 122,9 cm (Kids) 57,3 – 123,3 cm
(Family)
Maximum load: 100 kg
Temperature interval in use: 50-104°F or 10-40°C.
Storage temperature interval: 0 to 158°F or -18 to 70°C.
Humidity: 20-90, at 104°F or 40°C
Electrical power: 100-240 V AC, 50-60 Hz, 3.2-1.5 A
Model: W X Table
This tab. may only be used with the supplied control switch or Topstar-
certffied accessofies.
It is the sole responsibility of anyone installing, using, repairing or
servicing this desk to read this manual carefully. Keep this manual close to
your Sitness X table.
installation instructions
-
The table is assembled according to the above assembly instructions.
-
Connect the power cord to a wall outlet before use.
NOTE! The electrical cable must be completely movable. -
The desk is now ready for use. – The motors stop automatically when the desk reaches its lowest or highest position.
Using the Table
The table may only be used as a continuously adjustable work table between
sitting and stan-ding position.
The desk is intended exclusively for use indoors and in dry rooms (office
environment, etc.). The desk must not be overloaded – the maximum load is 100
kg. The system can be operated conti-nuously for a maximum of 1 minute. The
motors must stand still for approx. 9 minutes before they can be switched on
again.
Collision-detection
The system concept provides for collision-rela-ted damage to the equipment
to be avoided. If the desk detects a sudden change in resistan-ce, it stops in
the middle of its movement and retums approx. 50 mm. 25 mm travel can be
activated in both directions.
Standards & Certificates
The entire table series was developed to meet the DIN requirements of the
respective user group.
The SITNESS X UP TABLE KIDS range com-plies with the DIN 1729 standard: For
fumiture -Chairs and tables for educational institutions and EN 60335-1:
Safety of electrical appliances for household and similar purposes
The SITNESS X UP TABLE ADULT series complies with the DIN 527 standard Part:
1-3 Office furniture – Office desks and EN 60335-1: Safety of household and
similar electrical appli-ances
The colour/surface of the frame is approved according to standards: EN
12720:2009+A1:2013 Fumiture – Assessment of surface resistance to cold
liquids, EN 15186:2012 Fumiture – Assessment of surface resistance to
scratching
Safety regulations
When the desk is tilted up/down, maintain the required safety clearance to avoid trapping the moving tabletop and objects in the surrounding area. When moving the desk up and down, the user should be careful not to hurt anyone or damage any objects. The tabletop must not knock against a solid object if it tips over. Always remove all office chairs before moving the desk up/down. The table legs must not be altered or reconst-ructed in any way. The power cord must always be disconnected from the wall socket during service and repair works on the desk. Modifica-tions to the legs are absolutely forbidden. The desk may not be used as a lifting device for persons under any circumstances.
Maintenance and repair instructions
- After about 1 week of use, check that the screws are still properly tightened.
- If the desk cannot be lowered or raised, check the connections between the control box and the power outlet.
- If part of the electrical system is to be replaced, first unplug the electrical cable from the socket. Repla. the electrical part and then reconnect the electrical cable to the socket. The desk is now ready for use.
If the desk still does not work, contact Topstar Customer Service.
Service
Do not attempt to repair this product yourself as opening or removing
covers may expose you to dangerous voltages or other hazards.
**** The crossed-out dustbin symbol indicates that the item must be disposed
of separately from household waste. The item should be disposed of in
accordance with local regulations. environmental regulations for waste
disposal for recycling. By separating a marked object from household waste,
you help reduce the amount of waste in incinerators or landfills and minimise
possible negative impacts on human health and the environment. For more
information, please contact your Topstar customer service representative.
Manufactured by Theta Yngvi AG – Burgstr. 8, 8280 Kreuzlingen, Schweiz
Topstar GmbH
Augsburger Str. 29
D-86863 Langenneufnach
Mail: kundenservice@topstar.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>