Traffic Signs NZ European Arrow Board User Manual

: June 9, 2024
: Traffic Signs NZ

Table of Contents

Traffic Signs NZ European Arrow Board
FEATURES INCLUDE
FEATURES
INSTALLATION INSTRUCTIONS
TECHNICAL SHEET
FEATURES
DIMENSIONS
INSTRUCTIONS
CONNECTION DIAGRAM
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Traffic Signs NZ European Arrow Board

FEATURES INCLUDE

Traffic Signs unique NZ designed and made GEN2 Pivot AX Arrow System© has less moving parts, comes ready to operate and complies with latest NZTA requirements for NO arrow downward operations
333mm Xenon Lights compliant to European standard EN12352-2006
ASNZ engineered and certified for the following:
Maximum vehicle speed of 110km/h including wind speed of 47km/h in retracted position
Maximum vehicle speed of 50km/h including wind speed of 147km/h in extended position
ASNZ engineered and certified, fully aluminium frame including one piece construction section to limit maintenance issues and increase lifespan
Comes complete with electronic lifting system ready to wire up and operate
In cab controller for all functions including real time display
24 Volt
12 month warranty T&C apply (Patents pending)

Gen2 Pivot AX Arrow System© – 2015

FEATURES

Power Supply – 24 Volt
DETAS controller is used to control the main functions of the mother board
Emergency buttons with power supply motors has a disconnected relay for protection
TSNZ Pivot AX European Arrow Board will be delivered with frame and elec-tronic lifting mechanism
It is up to the end user and installation engineer to ensure the installation is fit for purpose regarding travel, height, suitable mountings and wiring to the vehicle
TSNZ has developed a secondary control function and processors to run the twin Pivot AX Arrow sys-tem, which can also provide the option to over-write the Arrow replacement

MAINTENANCE

Monthly lubrication is required using “dry glide” or similar type product for the lifting tracks of the board. This is not included as standard

INSTALLATION INSTRUCTIONS

Please follow the installation instructions attached:
TSNZ request installing a voltage regulator as part of the Euro board, any board fitted without one will not be covered under warranty.
The system has been designed and engineered to AS/NZS 1170.2.2011 and AS/NZS 1664.2.1997
Installation as per the attached drawings of the underside foot print requires 4x M16 class 8.8 nuts & bolts/ per side at 400mm centres. The forced per bolt has been calculated at 36.2kN.
Based on the wind speeds discussed in calculation register No. 3002-09 acting on the Generation 2 Ar-row Board. The resultant force per M16 mounting bolt has been calculated at 36.2kN. The structure that the Generation 2 Arrow Board is mounted to must be capable of withstanding the calculated resultant force of 36.2kN per bolt.
Please refer also to COPTTM and also note that a white up light with minimum output of 50 watts is to be attached to the deck to adequately illuminate the RG17.

For any further information refer to TSNZ Booklet or contact TSNZ direct

Page 2:- Technical Sheet
Page 3 & 4: – Overall Dimension & Underside of Frame
Page 5 & 6: – Operating Instructions
Page 7: – Layout for LED ‘s and Xenon Lights
Page 8 & 9: – Wiring diagrams for Main and Secondary Mother Boards

TECHNICAL SHEET

European Arrow Board

FEATURES

DIMENSIONS

INSTRUCTIONS

EUROPEAN ARROW BOARD

Before the remote will work you must make sure the Emergency Control Button

Control Functions

Emergency Butt
Battery Tester
Arrow Light control/ check
Lamp Failure
Motor Panel control check
External Arrow Bar check
Key On

To Lift Arrow Panel

Push “Key On” Button (7), light will come on and Down Button (5) light will come on, indicating the panel is down
Push Up Button (5) once and Panel will rise until it is in the upright position
Push Down Button (5) to return panel to the original starting position

Arrow Light Control

Push “Key On” Button (7) again
Select the Arrow (3) you require to be lit up

Checks: When Unit is turned on check:

Failed Lamp 4- Red light will appear when one of the 25 lights fail
Battery Charge Level 2-
Green Battery Full
YellowBattery 50% charged
Red Battery Flat

KEY ON – In order to avoid any involuntary action, pull out Emergency button 1 and press KEY ON |7 to activate the other functions on the controller

SECONDARY – REMOTE CONTROL – RG17/34 OVERRIDE

The override controller is used when the arrow board is in the standard “X” position, however you require the RG17/34 Blue/White arrow to show either left or right and not the standard “no arrow” function.

To select this function

Using the standard primary AX Pivot controller, select the X function that will have no downward arrow.
Using the secondary controller, select the arrow option left or right.
When completed, return the secondary controller to the X position and resume normal operations with the primary controller.

WARNING
PLEASE CONNECT THE DEVICE FOLLOWING THE LAYOUT SHOWN BELOW