AUTEL ROBOTICS EVO II Dual Radiometric Enterprise Bundle User Guide
- June 4, 2024
- AUTEL ROBOTICS
Table of Contents
- GETTING TO KNOW THE EVO II ENTERPRISE
- AIRCRAFT FRONT, REAR, AND LEFT SIDE VIEWS
- AIRCRAFT RIGHT SIDE, TOP, AND BOTTOM VIEWS
- FLIGHT INDICATION LIGHT
- SMART CONTROLLER
- CHARGING THE AIRCRAFT AND SMART CONTROLLER
- Autel Explorer™ APP
- PREPARING THE AIRCRAFT
- INSTALLING NEW PROPELLERS
- ENTERPRISE ACCESSORIES
- PREPARING THE SMART CONTROLLER
- POWERING UP
- TAKEOFF
- COMMAND STICK CONTROLS(MODE 2)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QUICK START GUIDE
Enterprise
Seattle 425-771-7776 | Tacoma
253-922-6087
Portland 503-641-3388 | Salt Lake City
801-878-9763
St. George 702-586-1152 | Las Vegas
702-586-1152
Boise 208-369-4388
www.KukerRanken.com
GETTING TO KNOW THE EVO II ENTERPRISE
Now you can explore, discover and create like never before. The EVO II Enterprise delivers not only advanced features like obstacles avoidance and intelligent flight modes, but also a high-tech muscle that brings home a top speed of 45 mph, 42-minute flight time, and an operating distance of 8 miles(FCC standard). In-flight performance, however, is just the start. The EVO II Enterprise version is equipped with 8x zoom and customizable accessories, and it’s optimized for aerial operation, and meets all the requirements of Inspection, Search and rescue, law enforcement, and firefighting. EVO II Enterprise comes with a 7.9-inch,2000 nit brightness Autel Smart Controller, which allows users to view the live feed at up to 1080p.
IMPORTANT
- Please consult all reviewable documentation before your first flight.
- Failure to operate the aircraft responsibly could lead to injury or damages and may void any applicable warranty coverage.
AIRCRAFT FRONT, REAR, AND LEFT SIDE VIEWS
1 Propeller
2 Motors
3 Front LED Indicators| 4 Landing Gear
5 Forward Vision System
6 Camera Gimbal
---|---
7 Power Button
8 Rear Vision System
9 Rear LED Indicators
10 Left Side Vision System
11SD Card Slot
AIRCRAFT RIGHT SIDE, TOP, AND BOTTOM VIEWS
12 Right Side Vision Sensor
13 Aircraft Battery
14 Air Vent
15 USB-C Port
16 Smart Controller Match Button / Match Indicator
17 Top View Vision System
18 Enterprise Accessory Interface
19 Ultrasonic Sensor
20 Downward Vision Lighting LED
21 Downward Vision System
FLIGHT INDICATION LIGHT
A LED indicator is located on the end of each aircraft arm. The front LEDs will light up solid red to help you identify the direction of the aircraft’s nose. The rear LEDs will display the current flight status of the aircraft. The chart below shows the meaning of each status indicator.
Indicator Key:
Slow Flashing: Flashes once every 2s
Fast Flashing: Flashes twice per second
Double Flashing: Flashes twice and then pauses and repeats
Alternate Flashing: Alternates among different colors
Indicator Key:
R ‒ Red Color
G ‒ Yellow Color
Y ‒ Green Color
Definitions of Flight LED Indicator Status
Normal Status
RGY – Alternate Flashing| System self-test is activated
YG – Alternate Flashing| The aircraft is warming up
G – Slow Flashing| The aircraft is in GPS mode
Warning
Y- Slow Flashing| The aircraft is in ATTI mode
Y- Fast Flashing| No connection between the aircraft and the smart controller
R – Slow Flashing| Low Battery Warning
R – Fast Flashing| Critically Low Battery Warning
R – Solid Light| Critical problems, IMU error
RY – Alternate Flashing| Abnormal compass, calibration is required /
Magnetometer interference
Compass Calibration
Y- Fast Flashing| Be ready to calibrate the compass/ The aircraft is
calibrating
G – Solid Light| Calibration is successful
R – Solid Light| Calibration is failed
Gesture Command
R – Fast Flashing| Gesture command has been received
SMART CONTROLLER
1 Left Command Stick
2 Gimbal Pitch Dial
3 Record Button
4 Customizable Button C1
5 Air Vent
6 HDMI Port
7 USB TYPE-C Port| 8 USB TYPE-A Port
9 Power Button
10 Customizable Button C2
11 Photo Shutter Button
12 * Zoom Control Wheel
13 Right Command Stick
---|---
- The function may alter, please take the practical effect as standard.
⑭ Battery Indicator
⑮ Antennas
⑯ Touch Screen| ⑰ Pause Button
⑱ Go Home Button
⑲ Microphone
---|---
⑳ Sound Speaker
㉑ Tripod Mount
㉒ Air Vent| ㉓ Bottom Hook
㉔ Protection Case
---|---
CHARGING THE AIRCRAFT AND SMART CONTROLLER
- Aircraft Battery: Plug the charging connector into the battery’s charge port.
- Smart Controller: Open the protector on the USB port and plug in the provided charging cable.
NOTE
- Always fully charge the aircraft and smart controller battery before flying.
- It takes approximately 90 minutes to fully charge the aircraft battery, and 120 minutes to charge the smart controller.
Autel Explorer™ APP
The Autel Explorer™ App is built in the smart controller, and it is used to
control the aircraft.
Autel Explorer™ App is optimized for EVO II Enterprise. The features are
Intelligent Photography, Mission Flight, and Intelligent Flight Modes.
Intelligent Photography includes more than ten intelligent functions such as
Dynamic Track and Smart Orbit to meet the customers’ various needs. Mission
Flight provides Waypoint, Rectangular, Polygon, and Oblique missions, which
allows the aircraft to perform the search and rescue, law enforcement, and
inspection operations automatically to meet the complex needs of various
industries.
NOTE
- The connected aircraft model will be displayed in the middle of the upper part of the main page. If you are using the App without connecting to the aircraft, you may need
to select the aircraft model to see the correct display.
PREPARING THE AIRCRAFT
-
Before powering on the aircraft, please remove the gimbal guard. Slowly pull it away from the aircraft as shown below.
-
Unfold the arms and propellers
IMPORTANT
Power off the aircraft before folding the arms. Fold in the rear arms and
propellers first, and then the front ones.
INSTALLING NEW PROPELLERS
Because the propellers come attached to the aircraft, the following instructions apply if you need to reinstall propellers. Propellers must be undamaged and firmly attached.
-
Attaching the Propellers
(1)Verify that the aircraft is powered off.
(2)Locate and match the propeller to each motor
(3)Press each propeller down firmly and rotate in the lock direction to securely attach the propeller. -
Detaching the Propellers
(1) Power off the aircraft
(2) Press each propeller down firmly and rotate in the unlock direction to detach the propeller.
Legend:
| Lock Direction: Fasten the propeller by rotating it as indicated
---|---
| Unlock Direction: Unfasten the propeller by rotating it as indicated.
| Black-coded propeller>Pairs with> Black-coded motor
| White-coded propeller>Pairs with> White-coded motor
WARNING
Power off the aircraft before attaching or detaching propellers.
IMPORTANT
Wear protective gloves when attaching or detaching propellers.
ENTERPRISE ACCESSORIES
The EVO II Enterprise can be equipped with accessories for different
applications.
Optional accessories: Spotlight, Loudspeaker, Strobe, and RTK module.
-
Detach the accessory
(1)Please ensure the aircraft is powered off.
(2)Lose the screws on both sides, and remove the accessory.
(2)Insert both ends of the protective cover into the corresponding slots. -
Attach the accessory
(1)Please ensure the aircraft is powered off.
(2)Lightly squeeze both ends to remove the protective cover
(2)Align the screws on both sides of the accessory with the screw holes and tighten the screws.
PREPARING THE SMART CONTROLLER
-
Unfold the antenna, detach the stick heads on the back of the smart controller handle, and screw them into the corresponding screw holes on both sides of the screen.
-
Adjust the antenna angle, and when the antenna and the back of the smart controller are at the angle of 180 or260, and the antenna surface is facing the aircraft, the signal quality of the aircraft and smart controller will reach the optimal condition.
POWERING UP
-
Press and hold the power button for 2 seconds to turn on the smart controller.
-
Press and hold the power button for 3 seconds to turn on the aircraft. The current battery level will be clearly displayed.
TAKEOFF
-
Place aircraft on a level surface, Stand well clear of the rear of the aircraft.
-
Start the motors by holding both command sticks for two seconds in one of these positions as shown below:
-
With the motors spinning, choose one of the following methods to take off:
Note: Before takeoff, place the aircraft on a flat and level surface and face the rear side of the aircraft towards you.
COMMAND STICK CONTROLS(MODE 2)
WWW.AUTELROBOTICS.COM
©2020-2021AUTEL ROBOTICS CO., LTD.
ALL RIGHTS RESERVED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>