Q-LINE GO GO LED Strip Light Instruction Manual
- June 9, 2024
- Q-LINE GO
Table of Contents
Q-LINE GO GO LED Strip Light
FEATURE
Note
Installation Precautions
- Install in the space without chemicals like sulfur, acid, halogen.
- The ambient temperature of the product is -20C~40C.
- To ensure the luminous effect, every five meters long strip should be connected to a driver.
- The quality of atmosphere should not be lower than the national secondary standard
- The air humidity is 40%-70%.
- Make sure that each power supply (GND) must be Connected together.
Product Warranty
A warranty period of five years is provided for products in normal use. For any faults arising during the period that are approved to be quality issue after inspected by our company, a product of the same model will be replaced for free.
The warranty does not cover any of the following situations:
- Any product damage due to usage not allowed in the instructions.
- Any product damage due to disassembling or wrong operations by the user.
- Severe appearance damage or deformation of the product.
When the product is installed, the bend should be avoided just at the position
of the LED or other components, s0 as not to easily damage the product and
atfect the service life of the product.
For non-replaceable light sources:
“The light source of this luminaire is not replaceable; when the light source
reaches its end of life the whole luminaire shall be replaced”;
- To ensure the long lfe span of strip, please do not pull the stripor driverwire hard during installation and using.
- In order to ensure the life and reliability of the light strip, please donot bendit in an arc less than 60mm in diameter, and do not fold it in half to avoid damage to the lamp beads or break
- To avoid the damaged components caused by Surge voltage or unstable current, please use the stable driver to power up the strip.
- During the installation process of the product, the product can not rub with other objects. It will cause the damage of nanolayer.
- UV light can damage the product. It will cause aging of nanolayer on the product and lead to the product can not be waterproof. This will seriously affect the life ofthe product
- During the installation process of the product, a little white powder will appear in some parts.The white powder is the Nanolayer peeled off when the wire is bent Therefore, the wire should not be bent excessively during the installation process.
- Please pay attention to the operation, whenthe power is working, do not touch the AC power terminal to prevent electric shock.
- Light strip products will release a lot of heat during use, and the product must be used in a ventilated environment.
- During the installation process, pay attention to the positive and negative poles of the powercord, and do not connect them wrongly.
- The power output must be consistent with the product voltage
INSTRUCTION INSTRUCTION
-
Cut the appropriate length on the outside of the side of the minimum cutting point
Cutting LED strip at the minimum cutting unit -
Use a blade to peel off the nanotechnology on the surface of the pad and use the exposed pad to facilitate wire connection
-
Mount the LED strip to the cable using the soldering-free Q-Line GO supply connectors
-
Pay attention to the positive and negative poles.
-
The protection level of the processing place is IP20, Please pay attention to protection
-
Use suitable profile and cover
-
Uncover the 3M glue release paper on the back of the LED strip in proper order and stick it to the installation position.
-
The mounting surface should be cleaned in advance.
-
Itis forbidden to tear off the 3M glue release paper on the back of the light strip at one time.
-
It is strictly forbidden to press lights and work when power is on.
Turn on the power
-
Install the power supply in a suitable location
Do not touch with wet hands to prevent electric shock. -
Connect the red and black wires of the light strip to the power supply
-
Turn on the power and light up the light strip
Using the connectors will reduce the protection to IP20 at the connection
point.
When installing in humid environments and outdoors, we recommend soldering in
combination with silicone glue at all connection points. This is to maintain
the IP degree of the strip which is IP65.
wwww.qlight.no
post@qlight.no
+47 905 11 849
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>