Brilliant G99830-75 Jacinda Ceiling Panel LED White Instructions
- June 9, 2024
- brilliant
Table of Contents
**Brilliant G99830-75 Jacinda Ceiling Panel LED White Instructions
**
Assembly
This product contains a light source of energy e’ciency class E.
The light source should be replaced by a qualified person.
The separate control gear should be replaced by a qualified person.
Caution: risk of elecric shock
Hereby, Brilliant AG declares that the radio equipment type Jacinda G99830… is in compliance with Directive 2014/53/EU. The full EU declaration of conformity can be requested at the following internet address: www.brilliant- ag.com
Frequency Range: 2450 Mhz
Transmitted Power: -12.22dBm EIRP
Operational temperature range Device: 0 ~ 40 degree Celsius
www.brilliant-ag.com
REMOTE CONTROL
Quick Start: Keep one of these buttons pressed while turning the luminaire on for the first time to connect the remote control with the luminaire.
See: „Assign the remote control“
-
On
-
Fast choice button brightness
-
Fast choice button white
CDL: cold white
DL: daylight
CW: neutral white
WW: warm white -
Memory function on
-
turn the light colour to cold white
-
night light mode on/off
-
EASY DIM FUNCTION
-
Group 1-4 on/ connect
-
Off
-
Memory function off
-
Increase brightness
-
turn the light colour to warm white
-
decrease brightnes
-
Lock/unlock the key pad
-
Group 1-4 off
-
Setup timer. The lamp will turn off after 10 minutes
-
Setup timer. The lamp will turn off after 20 minutes
-
Setup timer. The lamp will turn off after 30 minutes
-
Setup timer. The lamp will turn off after 60 minutes
Prior to first use of the remote control, you must assign the light to the remote control. Please perform the following steps.
Assign the remote control:
- Turn on the light at the switch on the wall
- You have 2 seconds to press the “On” button (“I”) on the desired shortcut key. Press this button until the light flashes.Flashing indicates successful assignment of the light.
To assign several lights to one group, repeat the previous steps until you have assigned all of the lights. Once you have assigned several lights to one group, these lights will always operate synchronously. The lights can no longer be controlled individually (e.g. for dimming, changing colour, on/off).
Undo assignment / reset light:
- Disconnect the light from the power supply at the switch on the wall for approx. 10 seconds.
- Turn the light back on at the switch on the wall.
- Press the button of the linked group 5 times repeatedly.
- The light has successfully reset from the previous linked group.
The light can now be reassigned to a remote control or group by following the steps outlined above. To remove several lights from a group, please repeat the previous steps for each light.
Master ON/OFF:
Pressing the Master ON/OFF button will either switch on or switch off all of the lights allocated to a remote control.
Simultaneous control of all lights assigned to a remote control:
If you want to simultaneously configure all lights assigned to a remote
control (e.g. setting the colour), first switch off all of the lights with the
“Master OFF” button and then switch them back on with the “Master ON” button.
All of the lights will now respond to your input.
The lights can be controlled within a radius of up to 20m of the remote
control. However, the range may be affected by walls or other interference
factors. If the range of the remote control decreases, please check the
batteries (2x AAA, 1.5v) and replace them if necessary
Activating the memory function of the wall switch with the remote control:
Press and hold down the button 4 on the remote control for at least 3 seconds. The light flashes to indicate that the last status set via the remote control will be restored when the light is switched on again via the wall switch.
Deactivating the memory function of the wall switch with the remote control:
When the button 13 of the remote control is pressed and held down again for at least 3 seconds, the light blinks to indicate that the memory function of the wall switch has been deactivated.
Notes on battery disposal
When it comes to sale of batteries or delivery of devices which contain
batteries, we are required to draw your attention to the following:
As the end user, you have a legal obligation to return used batteries. You can
return old batteries which we have, or have had, as new batteries in our
range, to our shipping warehouse (Brilliant AG, Brilliantstr.1, D – 27442
Gnarrenburg), or at your local dealer, free of charge. The symbols shown on
the batteries have the following respective meanings:
Pb = Battery contains more than 0.004% lead by mass
Cd = Battery contains more than 0.002% cadmium by mass
Hg = Battery contaiss more than 0.0005% mercury by mass
The crossed out dustbin symbol means that the battery may not be included in household rubbish. Please observe the notes above.
Battery information
If required, clean the battery and device terminals before inserting.
Remove exhausted batteries from the device without delay! High risk of
leakage!
Never expose batteries to excessive heat such as sunlight, fire or similar!
Always replace all batteries at the same time.
Only use batteries of the same type. Do not use different types or used and
new batteries together.
Remove batteries from the device when unused for long periods.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>