Rayfoto S800 4K Dual Dash Cam Built-in WiFi GPS Front User Manual

: June 9, 2024
: Rayfoto

Table of Contents

Special Note
Introduction
Safety Information
Getting Started
Screen Swipe Definition
Product Overview
Buttons and Functions
Installation
Basic Operation
Setting Interface
System Settings
File Browsing
App Introduction
GPS Player Software
GPS Player Uses Interface
Specifications
FAQ’s
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Rayfoto S800 4K Dual Dash Cam Built-in WiFi GPS Front

S800 4K Dual Dash Cam Built-in WiFi GPS Front

Special Note

This product can be directly clicked on the screen to select, and the button function corresponds to the touch-sawn function. (Auto record when power co) The first boot may take about 5 seconds, please be patient. Touch screen operation should not be too fast, there will be a little delay

Introduction

Thank you for purchasing our product, We hope that this user manual helps you get started with the basic features that our camera has to offer. This camera is equipped with a 4K+ 216§30FPS camera Display. lt has advanced built-in Wi- FLGPS and G-Sensor. built-in WDR, built-in HDR, Emergency Video lock button, Auto-ReconiAudio recording, Loop cycle recording, etc. This user manual is subject to change without prior notice.

Safety Information

Please read this instruction manual carefully before using the camera. It contains important information for your safety as well as operating and maintenance instructions.
Follow all safety precautions in order to prevent damage due to improper use of the camera. 3.
In the event of improper use or erroneous handling, no liability can be assumed for any possible damage which may occur.
You should not install this dash camera in a place that would obstruct or reduce a driver’s view. Make sure your usage complies with pertinent vehicle codes of your state, province, territory, or country.
You should release the required record notification to the occupant in the car if you will record sounds or other information signals related to car activity.
You should avoid extended exposure of the dash cam to direct sunlight or extreme temperatures (either high or low tempera-ture) which tend to degrade or damage the unit and its normal functionality.
You should check and verify the camera at least every month, including the memory card, to ensure the video reception and recording are working properly. For each use, you should verify that the camera unit, the visible lights, and the audible sounds are working normally.
Do not by to open the cover or try to repair it yourself. If the accessories for this device have any problems, please contact the seller for assistance.
Pay careful attention when deaning the lens surface. Use a soft mast cloth to clean the lens to avoid compromising video quality.
You should use the camera unit in the way it Is intended. You should not use the dash cam unit In a way that would be illegal or that tends to physically damage the unit, or tend to cause danger to the safe operation of the vehicle or the occupants.
This device is intended to be used inside the vehicle only.
Do not expose this product to rain, moisture, or water under any circumstances or it will result in external or internal damage.
Do not operate or install the camera while driving, or attempt to change any setting, etc.
If any damage is caused by failure to follow the instructions, the warranty will be voided.

Getting Started

Before installation, please check the accessories carefully to ensure that the product and accessories are correct and complete.
During installation, be sure not to insert the car key into the power supply, and do not insert or remove any machine accessories like a micro SD card or rear camera when the camera is powered on. These actions should be completed when power is turned off.
When the car key Is plugged Into the vehicle, the camera will automatically turn on. Please check whether the function of power on/off, the front and rear cameras display are normal.
If you need to download the recording videos and images, please turn off the camera first before removing the micro SD card.
You must use U3 high-speed card (recommended capacity 8GB-256GB), lower than U3 will cause problems like video stutter, black screen, and video cannot be recorded or cannot be played.
Do not remove the Micro-SD card while it is saving or reading data.
Make sure to remove the plastic screen protector on the lens and on the screen before recording videos. Otherwise, your videos will look blurry and out of focus.

Screen Swipe Definition

Swipe left or right to switch perspectives. Turn on the WIFI function to return to the main interface, slide up and down to wake up, or hide the WIFI interface. After exiting the mobile APP for a few minutes, the WIFI function will be automatically turned off, and you need to enter the menu to turn it on again.

Product Overview

Buttons and Functions

| Click to enter the screen saver
---|---
| Click to enter the menu
| Click to turn on the recording/turn off the recording
| Video browsing
| Click to enable recording/disable recording
| Click to lock video during recording
| Tap to take a photo during the recording
| Front and rear viewing angle switching

Installation

Insert the micro SD card into the dash cam. Maximum support is 256GB. Please make sure the camera is turned OFF First. Then align the gold-plated contacts facing towards the back of the camera (Screen Side). Then insert the memory card halfway in. Then use the fingernail or a paper clip to push the card all the way inward until it clicks and locks in place. The camera comes with the default settings which allows you to start using your camera right out of the box without changing any settings. Please make sure to format the memory card before first-time use.
Clean the spot on your windshield where you would like to mount the camera and confirm the placement. We recommend installing the camera near the rear view minor of the driver’s opposite side.
Next, Press the bracket firmly against the windshield.
Install the rear camera on the rear windshield using adhesive tape or near the license plate using screws.

the rear camera is designed to record footage at the rear of the vehicle. It should not be used as an aid In backing up. If you want to use the reversing function then connect the red trigger cable of the rear camera extension cable to the positive lead of the car reversing lamp. This step is optional and only recommended for a rear view mirror dash camera.
Plug the supplied car charger into your vehicle’s accessory port, and the other end into the micro USB port. Route the cable alongside the interior trim for better looking.
Format the micro SD memory card by going to Menu > System Settings > Format then select Yes.

Basic Operation

POWERING ON
The device will power on automatically when connected to power and can also be powered by pressing the power button.
POWERING OFF
When power is disconnected the device will save the last video file and power off.
VIDEO RECORDING
After the car engine is switched on, the camera will automatically tum on and start recording.
NAVIGATING MENUS
First press the OK button to stop recording, then press the MENU button to enter the menu settings.

Setting Interface

Resolution
This setting allows you to set the video recording resolution. 4K +2K for dual-camera recording.
Loop Recording
This setting allows you to control the duration of each individual loop dip. It will delete the oldest files and record newer files over and over when the memory card is full Clips can be set to a durative of 1 minute or 3 minutes. 5 minutes, or OFF.
Dual Cam Display
This setting allows you to control the display screen of each camera. can be set to Front. Rear, or Front/Rear. Record Audio This device has a Built-in Microphone so you can record audio along with the video. The microphone can easily be toggled off if you prefer not to record audio.
Date Stamp
This option allows you to turn ON or OFF if you want the time and date to appear at the bottom of the video.
G-Sensor is a 3-axis impact gravitational accelerometer, designed to detect physical and gravitational forces on the camera.
Once G-sensor is triggered due to physical or gravitational impact force on the camera, the current video file will be locked as an emergency file to avoid getting overwritten. Off / Low / Middle / High for optional, default is OFF.
Speech Recognition
You can control your device by voice. as follows:

System Settings

Screen Saver
Turns the screen off after a set time of no activity to prevent driver distraction. The camera will continue recording and the screen can be woken up by pressing any button. Options 30 sec,1 minute, 3 minutes, or OFF.
Time Display
This option allows you to turn ON or OFF if you want the display screen of Clock.
WIFI
This feature will allow you to turn WiFi broadcast from the camera so you can connect your phone with the dash camera to access videos, photos, and settings.
Date/Time
Set system date, time, and date.
Time System
Set the time system to 12 hours or 24 hours.
Beep Sound
Turns the sound on or off each time a button is pressed. ON/OFF Language Sets the on-screen display language to English, Simplified Chinese, Traditional Chinese, French, Spanish, German, Italian,-Japanese, Korean, Russian, Arabic, etc.
Parking Monitor
This Dashcam parking monitor feature is configured to record in a time-lapse configuration. It is very useful for other non-col-vision incidents that may occur when your vehicle is parked in a busy parking lot. Options OFF / ON, default is OFF.
Frequency
Here you should choose the frequency accordingly to your power supply specification used in your country based on your geographical location. 50Hz or 60Hz
Fatigue Driving Reminder
You can also set a driving time reminder to prevent fatigue by driving 1 hour,2 hours,4 hours, or off.
Time Zone,
You can also set the GMT time-zone value so the camera will set the date and time based on the GMT value selection when it receives the GPS signal lock Time zone will not change automatically when it starts/ends daylight saving time, please adjust manually at that time.
GPS Information
The GPS signal will show if the camera is receiving the signal successfully. With this feature, you can also check the location (longitude and latitude) or driven route when you playback the video using the dedicated GPS player.
Format the micro SD card ready for use with the camera. YES or NO
Default Setting
Click to reset the system setting to default. NO or YES
Version Into
To check the dash camera system firmware version

File Browsing

Press the UP button in standby mode to enter the file browsing. Playback mode allows you to review the saved video footage and playback the video. To select a video for playback navigate using the up and down button then press the Olt button to play.

| |
---|---|---
Ordinary Video Files| Lock Video File| photo file

App Introduction

This camera uses the Road cam App, which allows you to turn WiFi broadcast from the camera so you can connect your phone with the dash camera to access videos, and photos and manages some camera settings.

DOWNLOAD & SETUP

Search for ‘Road cam’ on App Store. Google Play or by scanning the QR code below:
|
---|---

http://www.ligoor.com/app/roadcam/roadcam.html

Allow app permissions
.
Standby mode Press MENU> On SSID Rayfoto-5800-XXXX and password 12345678 will appear on the camera screen; Turn on the camera’s WI-Ft by pressing the Menu > system Settings > Win > On SSID Rayfoto-S800-XXXX and password 12345678 will appear on the camera screen.
Navigate to your smartphone’s WiFi settings and look for the SSID Rayfoto-S800-XXXX network and enter the password 12345678 to connect.

In the App Preview mode, press the cogttorri or settings icon on the top right corner to enter if you want to make any changes with the camera setup.
Tap on the Video icon from the app home screen to access all recorded videos saved on the Micro SD card. You can download, delete or even play videos from the app.

GPS Player Software

Use the device that comes with a player or visits httplAwm.sunningsoft.comfen/pcgps.html

GPS Player for Windows (Windows7, Windows8, Windows10)
GPS Player for Mac (Mac 10.11, Mac 10.11 above)
Simply remove the memory card from the camera and insert it directly into the PC. then find and install GXPLAYER.EXE With this player you can play your videos on your computer screen with GPS information, driving route vehicles speed. distance, position, data displays, and maps.

GPS Player Uses Interface

After your email: [email protected]

Specifications

Model	$800
Processor	Novatek 96670
Sensor	Sony IMX335(Front)

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FAQ’s

Q: Video is fuzzy?
A: Please make sure the lens of camera is clean and there is no dirt on windshield also. A: Remove plastic screen protector on the lens and on the screen display. (See page 2)
Q: Camera showing Memory Error
A: Please ensure that the memory card is U3 high-speed card (8GB-256GB) and format before using.
Q: Menu button/ buttons not working.
A: Press OK button first to stop recording and then press MENU button again
Q: Camera Locks many videos automatically?
A: Please make sure you manage G-sensor setting. This setting depends on type of car or truck you are driving and how much vibration your car/truck is creating based on suspensions and road condition.
Q: Camera gets hot?
A: It is normal for your camera to run slightly hot.
Q: Camera turns ON / OFF frequently automatically
A: Please make sure that Motion Detection is set to OFF and Parking Mode is also set to OFF.
Q: Micro SD Card is not going in.
A: Please make sure you align micro SD card correctly with gold contacts facing towards the screen. {See page 5)
Q: Date and Time is not staying the same
A: Please go to camera’s system settings > Time Zone > Set the correct GMT value > OK to confirm. Every-time you have GPS signal, you will always have correct date and time.