Adision Lighting OD5STRGBCW Up-Down Wall Sconce User Manual

June 9, 2024
Adision Lighting

Adision Lighting OD5STRGBCW Up-Down Wall Sconce

Adision-Lighting-OD5STRGBCW-Up-Down-Wall Sconce

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU MAY NEED THEM AT A LATER DATE.

CAUTION

  1. TURNOFF FLECTRICAL POWER BEFORE STARTING INSTALLATION OR LIGHT FIXTURE.

  2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATIONCODE BY A
    PERSON FAMILIAR wITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

  3. CAUTION, RISK OF FIRE. CONSULT A QUALIFIED ELECTRICIAN TO ENsURE CORRECT BRANCH CIRCUT CONDUCTOR.

  4. FOR EXTERNAL USE ONLY, RECOMMEND APPLYING WATERPROOF SILICONE TO SEAL AROUND TRIM AND CEILING.

GENERAL
ALL ELECTRICAL CONNECTIONS MUST BE IN ACCORDANCE WITH LOCAL AND NATIONAL ELECTRICAL CODE (N.E.C.) STANDARDS. IF YOU ARE UNFAMILIAR WITH PROPER ELECTRICAL WIRING CONNECTIONS, PLEASE HIRE A QUALIFIED ELECTRICIAN. REMOVE THE FIXTURE ANDITS COMPONENTS FROM THE BOX AND MAKE SURE THAT NO PARTS ARE MISSING.

INSTRUCTIONS

  1. PRIOR TO INSTALLATION, INSTALL MOUNTING PLATE (INCLUDED) INTO THE ELECTRICAL BOX WITH MOUNTING SCREWS (INCLUDED).
    DRIVE SCREWS COMPETELY TO THE END OF THE JUNCTION BOX.Adision-Lighting-
OD5STRGBCW-Up-Down-Wall Sconce-2

  2. CONNECT SUPPLY WIRES TO WIRES ON FIXTURE WITH WIRE NUTS (INCLUDED). CONNECT WHITE TO WHITE, BLACK TO BLACK,AND COPPER WIRE TO GREEN WIRE AS A GROUNDING CONNECTION.Adision-Lighting-OD5STRGBCW-Up-Down-Wall Sconce-3

  3. CAREFULLY TUCK ALL WIRES BACK INTO THE JUNCTION BOX.
    PUT THE WALL SCONCE OVER THE MOUNTING PLATE AND MATCH THE MOUTING HOLES ON THE PLATE AND THE SCONCE.Adision-Lighting-OD5STRGBCW-Up-Down-Wall
Sconce-4

  4. THEN DRIVE SCREWS COMPLETELY TO SECURE AND COMPLETE INSTALLATION. USE WATERPROOF SILICONE TO SEAL BETWEEN THE EDGES AND THE FUXTURE

Adision-Lighting-OD5STRGBCW-Up-Down-Wall Sconce-5

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should
be installed and operated with minimum distance 20cm between the radiator& your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals