CROW ELECTRONIC ENGINEERING 4 Outputs Relay Expander Board Output Module Instruction Manual
- June 8, 2024
- CROW ELECTRONIC ENGINEERING
Table of Contents
ELECTRONIC ENGINEERING 4 Outputs Relay Expander Board Output Module
Instruction Manual
4 Outputs Relay Expander Board Output Module
ELECTRONIC ENGINEERING LTD.
4 OUTPUTS RELAY EXPANDER BOARD OUTPUT MODULE 12V/1A
Installation Instruction
Before starting to install and work with this device Please read the Safety Instructions.
Scope of delivery
RELAY Board
Plastic board holder (x4)
Installation Instruction
Introduction
The RELAY board has been designed for internal installation inside a plastic
enclosure. The RELAY board connects to the control panel main board via the 4
wire keypad buss.
The RELAY board provides four independent changeover relay contacts that can
be used to interface to other devices such as garage doors, automatic gates,
etc.
Operation Instructions
The CROW control panel allows for up to 8 programmable alarm outputs. 4 of
these outputs are available as standard on-board on the control panel and the
additional outputs can only be accessed via this optional relay board.
The Relay unit has 8 Open Collector transistors’ outputs and 4 Relays outputs.
The Open Collectors switch to 0V when the output is ON. Every control to this
board activates one relay output and one Open Collector Outputs.
Mount the RELAY board
Be sure that the Control Panel’s AC plug and battery are unplugged before
connecting the unit.
A. Insert the plastic holders to the 4 holes at the corners of the RELAY
board.
B. Remove the cover from the glue side of the plastic holders.
C. Attach the board and glue it to a free area at the right side of the
control panel base.
D. Connect the 4 Bus wires to the Terminal Block (Data, Clock, Neg, Pos).
Use only the supplied plastic holders.
Outputs Setting
There are 4 jumpers on the RELAY board labeled as “Learn” from 1 – 4. These
jumpers are used to select the control outputs and relate them to the output
relays.
The first jumper labeled as “1”, relates to Relay #1, through to the jumper
labeled “4” that relates to Relay # 4.
If the jumper #1 is in OFF position then relay #1 will follow the programmed
options for output # 1, if jumper #1 is ON then relay #1 will follow the
programmed options for output # 5.
If jumper #2 is OFF then relay # 2 follows output # 2, if jumper #2 is ON then
relay #2 follows output # 6, etc, up to jumper 4 making relay # 4 follow
output #4 or #8.
**** Please refer to the following table for more details;
JUMPER| RELAY #1
JUMPER #1| RELAY #2
JUMPER #2| RELAY #3
JUMPER #3| RELAY #4
JUMPER #4
---|---|---|---|---
OFF| Output #1| Output #2| Output #3| Output #4
ON| Output #5| Output #6| Output #7| Output #8
Control Panel setup
The following option must be turned ON in the Control Panel for the RELAY
activation :
P25E10E……….. OPTION 6 MUST BE ON
Technical Data
| Data a Protocol | CROW CONTROL PANEL BUS |
|---|---|
| Operation Voltage | 11 to 16Vdc |
| Current Consumption | Active: 20mA per active |
Standby: 15mA
Relay Contacts| 24VDC 1A
Open Collector Drive
Outputs| 12VDC 50mA
LED Indicator| Individual LED for each relay
Operating temperature| -10 – +50 °C
Storage temperature| -20 – +60 °C
Humidity (EN60721)| < 85 `)/0 r.h., non condensing
EMI rejection up to 1 GHz| > 10 V/m
COMPILES WITH: EN 50130-4+A1+A2, EN301489-3, EN300220-3, EN60950-1, EN61000-6-3, EN55022 KL. B, EN50371
CROW ELECTRONIC ENGINEERING LTD. (“Crow”) – WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the purchaser (hereunder the
“Purchaser”) purchasing the products directly from Crow or from its authorized
distributor.
Crow warrants these products to be free from defects in materials and
workmanship under normal use and service for a period of 24 months from the
last day of the week and year whose numbers are printed on the printed circuit
board inside these products (hereunder the “Warranty Period”).
Subject to the provisions of this Warranty Certificate, during the Warranty
Period, Crow undertakes, at its sole discretion and subject to Crow’s
procedures, as such procedures are form time to time, to repair or replace,
free of charge for materials and/or labor, products proved to be defective in
materials or workmanship under normal use and service. Repaired products shall
be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related,
directly or indirectly, to products returned to Crow for repair or replacement
shall be borne solely by the Purchaser.
Crow’s warranty under this Warranty Certificate does not cover products that
is defective (or shall become defective) due to: (a) alteration of the
products (or any part thereof) by anyone other than Crow; (b) accident, abuse,
negligence, or improper maintenance; (c) failure caused by a product which
Crow did not provide; (d) failure caused by software or hardware which Crow
did not provide; (e) use or storage other than in accordance with Crow’s
specified operating and storage instructions.
There are no warranties, expressed or implied, of merchantability or fitness
of the products for a particular purpose or otherwise, which extend beyond the
description on the face hereof.
This limited Warranty Certificate is the Purchaser’s sole and exclusive remedy
against Crow and Crow’s sole and exclusive liability toward the Purchaser in
connection with the products, including without limitation – for defects or
malfunctions of the products. This Warranty Certificate replaces all other
warranties and liabilities, whether oral, written, (non-mandatory) statutory,
contractual, in tort or otherwise. In no case shall Crow be liable to anyone
for any consequential or incidental damages (inclusive of loss of profit, and
whether occasioned by negligence of the Crow or any third party on its behalf)
for breach of this or any other warranty, expressed or implied, or upon any
other basis of liability whatsoever. Crow does not represent that these
products can not be compromised or circumvented; that these products will
prevent any person injury or property loss or damage by burglary, robbery,
fire or otherwise; or that these products will in all cases provide adequate
warning or protection.
Purchaser understands that a properly installed and maintained product may in
some cases reduce the risk of burglary, fire, robbery or other events
occurring without providing an alarm, but it is not insurance or a guarantee
that such will not occur or that there will be no personal injury or property
loss or damage as a result. Consequently, Crow shall have no liability for any
personal injury; property damage or any other loss based on claim that these
products failed to give any warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage
with regards to these products, regardless of cause or origin, Crow’s maximum
liability shall not in any case exceed the purchase price of these products,
which shall be the complete and exclusive remedy against Crow.
ELECTRONIC ENGINEERING LTD
ISRAEL:
12 Kineret St., P.O.B 293, Airport-City, 70100.
Tel: 972-3-9726000
Fax: 972-3-9726001
E-mail: support@crow.co.il
ITALY:
DEATRONIC Via Giulianello 1/7 00178 ROMA, ITALY
Tel: +39-06-7612912
Fax: +39-06-7612601
E-mail: info@deatronic.com
USA:
2160 North Central Road, Fort Lee, N.J. 07024
Tel: 1-800-GET CROW (201) 944 0005
Fax: (201) 944 1199
E-mail: support@crowelec.com
AUSTRALIA :
142 Keys Road Cheltenham Vic 3192
Tel: 61-3-9553 2488
Fax: 61-3-9553 2688
E-mail: crow@crowaust.com.au
LATIN AMERICA:
CROW LATIN AMERICA 5753 NW 151ST.Street
MIAMI LAKES,
FL 33014 USA
Tel: +1-305-823-8700
Fax: +1-305-823-8711
E-mail: sales@crowlatinamerica.com
POLAND:
VIDICON SP. ZO. O. 15 Povazkowska St. 01 797
Warsaw Tel: 48 22 562 3000
Fax: 48 22 562 3030
E-mail: vidicon@vidicon.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>