ASHLEY L000588 Jodene Pendant Light Instruction Manual
- June 8, 2024
- Ashley
Table of Contents
L000588 Jodene Pendant Light
Instruction Manual
ASSEMBLY INSTRUCTION:
READ AND SAVE THE INSTRUCTIONS.
L000588 Jodene Pendant Light
WARNING
Failure to read and carefully follow all instructions could result in fire or
serious bodily injury or death.
WARNING
To avoid in shock, fire or serious bodily injury or death it is very important
that the electricity servicing the fixture is turned off before and during
installation.
CAREFULLY READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY. Because this fixture is
connected to live electrical wires, it is strongly recommended to consider
installation by a licensed electrician.
THIS FIXTURE SHOULD TAKE APPROXIMATELY 10 MINUTES TO ASSEMBLE.
MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED.
TOOLS: You will need following tools or equipment: ladder, screwdriver,
adjustable wrench.
UNPACK THE FIXTURE: You should have received the following parts in the
package: canopy, extension pipes-12″ – 6 pc. & – 2 pc. To protect the finish,
place all parts on a soft surface.
MOUNTING HARDWARE PACKAGE: (2) 1-4 x 1-1/4″ screw. (2) Plastic wall
Anchor, (2) P3 Connectors, (1) P2 Connector, (2) Bush, (2) Nuts, (2) Star
Washer.
FIXTURE ASSEMBLY:
Determine the length of extension pipes required to hang the fixture at the
desire height, remove or add pipes as desired. Use same no. of – pipes of
equal length of each side. Screw the desired no. of pipes with one another on
both the sides. Thread fixture wire up through the extension pipes on both
side. Screw the extension pipe at the bottom on to the fixture lamp. Attach
the canopy to the top pipe and then screw with the nut.
If the external flexible cable or cord of this luminaire is damaged, it shall
be exclusively replaced by the manufacturer or his service agent or a similar
qualified person in order to avoid a hazard.
** THIS PRODUCT IS FOR INDOOR USE ONLY! OUTDOOR USE COULD RESULT IN SHOCK.
FIRE OR SERIOUS BODILY INJURY OR DEATH. AU WIRING MUST BE DONE IN ACCORDANCE
WITH NATIONAL AND LOCAL ELECTRIC CODES. IT IS STRONGLY RECOMMENDED THAT YOU
USE A QUALIFIED ELECTRICIAN
WARNING THIS FIXTURE MUST BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF
SUPPORTING THE FIXTURE. FAILURE TO FOLLOW THIS REQUIREMENT COULD RESULT IN THE
FIXTURE FALLING CAUSING SERIOUS BODILY INJURY OR DEATH.
WARNING** TO AVOID SHOCK, FIRE OR SERIOUS BODILY INJURY OR DEATH IT IS VERY
IMPORTANT THAT THE ELECTRICITY SERVICING THE FIXTURE IS TURNED OFF BEFORE AND
DURING INSTALLATION.
- Attach the cross bar to the ceiling outlet box using the two screw provided with the outlet box. (Note : If the screws with the outlet box are too short, use the (2) 1-4 x 1-1/4′ screws provided in the mounting hardware package).
- Connect the white or ribbed fixture wire to the white supply wire in the outlet box using the P3 wire connectors provided. Connect the black or smooth fixture wire to the black supply wire in the same manner. Install the fixture Supply Ground Wire under the green group screw on the crossbar then connect the fixture Supply Ground Wire to the supply the Supply Ground Wire in the outlet box using the P2 wire connector provided.
- Tuck the wires carefully inside the outlet box. Spread the electrical splices so that the black wires are on one side of the outlet box and the white wires are on the other side. Next raise the canopy to the ceiling and attach back to cross bar by using two screw provided with the canopy.
FINAL ASSEMBLY
-
Install a 60 watt max. Medium base type “A” bulb (not included) into each socket.
WARNING Installation of a bulb exceeding 60 watts maximum could result in fire, serious bodily injury or death. -
Slide small metal washer, diffuser, large metal washer over the nipple of stem and secure with the finial,
-
Restore power after installation is fully complete. Your fixture is ready for use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>