velleman VTSSC50N Soldering Station with Ceramic Heater User Manual

: June 8, 2024
: Velleman

Table of Contents

velleman VTSSC50N Soldering Station with Ceramic Heater
Introduction + Description
Safety Instructions
Features
Operation
Common Causes for Tip Failure
Important Remarks
First Use
Technical Specifications
Velleman® Service and Quality Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

velleman VTSSC50N Soldering Station with Ceramic Heater

Introduction + Description

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.
Read and understand this manual and all safety signs before using this appliance.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids. Never put objects filled with liquids on top of or close to the device.
Always disconnect mains power when the device is not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.
Caution! After switching off, leave the power cord plugged in for a few minutes. When you switch off the unit, the automatic cooling function blows cooling air through the heater pipe for a short period. This protects the heater from damage and extends its lifetime. Do not disconnect the mains plug during this cooling process.
Do not crimp the power cord and protect it against damage.
Warning! If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid any hazard.
Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
Plug the power cord into a suitable, earthed mains outlet.
Risk of electroshock when opening the cover. Touching live wires can cause life-threatening electroshocks. Do not disassemble or open the housing yourself. Have the device repaired by qualified personnel.
Do not operate the device with wet hands.
Never use the device on live electronic circuits. Make sure power to the work piece is cut and capacitors are discharged.
Do not use near inflammable products or in explosive atmospheres. Heat can cause fire to inflammable products even when they are not in sight. Only use in properly ventilated rooms.
Incorrect use may cause fire.
Do not touch the shafts, tips, or hot air gun as this can cause serious burns. Keep the tips and hot air away from the body, clothes, or other flammable material. Do not aim the hot air gun at the eyes. Use gloves and/or heat- resistant tools to pick up the PCB assembly to prevent burns. Always return the irons and gun to their stands between uses; always let the device cool down after use and before storage.
Place the device on a level, stable, and fire resistant working surface.
WARNING! – This tool must be placed on its stand when not in use; do not leave the tool unattended when switched on.
Do not inhale solder fumes. The vapours that are released during soldering are harmful. Therefore, you shall only use the soldering station in well-ventilated areas or under an exhaust hood (solder fume extractor). Dispose of fume filters and solder residue in accordance with local regulations.
Use the soldering iron on a heatproof workbench.
Place the soldering iron in its holder after use.
Let a hot soldering iron cool down naturally and do not immerse in water.

Features

manual temperature setting
power-on LED indication
with on/off switch
ceramic heating element
with stand for left- or right-handed use
standard tip (incl.): BITC50N2 (1.0 mm).

Operation

Verify whether the operating voltage of the unit is compatible with the mains voltage prior to plugging in this device.
Make sure that the device was not damaged in transit.
Use the rotary control on the front panel to set the desired temperature.

Common Causes for Tip Failure

The tip is not sufficiently tinned.
Wiping the tip on a surface with high sulphur content or on a dirty or dry sponge or rag.
Contact between the tip and organic or chemical substances such as plastic, silicone, grease, etc.
Impurities in the solder and/or solder with a low tin content.
Note: The heating element may be damaged when its temperature reaches 430 °C (806 °F).

Important Remarks

Remove and clean the tip after heavy or moderate use. We recommend cleaning the tip every day if the device is used on a daily basis. Clear excess solder from the tip assembly.
The supplied soldering tip is made of iron-clad copper and will retain its projected life span if used properly.
Always tin the tip before returning it to the holder, prior to deactivating the station or in case of long periods of inactivity. Clean the tip with a wet sponge prior to use.
Do not use temperatures over 400 °C (750 °F) as this will shorten the life span of your tip.
Do not exert too much pressure on the tip while soldering to avoid damage.
Never clean the tip with a file or other abrasive materials.

First Use

Attach the holder to the base as shown in the picture (screw included).

Technical Specifications

max. heater power for soldering iron …………………………………………………………………. 48 W
power supply …………………………………………………………………………………… 230 V~, 50 Hz
temperature range………………………………………………………………………………… 150-420 °C
low-voltage iron ……………………………………………………………………………………………. 24 V
weight …………………………………………………………………………………………………….. 1.85 kg
dimensions ………………………………………………… 160 x 120 x 95 mm (without stand and iron)
replacement bits ………………………………………………………… BITC50N1, BITC50N3, BITC50N4

Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.

© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.

Velleman® Service and Quality Warranty

Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer Products (for EU):

All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.

Not covered by warranty:

all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;
consumable goods, parts or accessories that are subject to an aging process during normal use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber parts, drive belts… (unlimited list);
flaws resulting from fire, water damage, lightning, accident, natural disaster, etc.…;
flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer’s instructions;
damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
damage resulting from an inappropriate packing and shipping of the article;
all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.
Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
Repairs occurring after warranty expiration are subject to shipping costs.
The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article (see article’s manual).