cordinate 51766 18-Inch LED Light Fixture with 2-USB Fabric Charging

Station with Braided Cord

Thank you for your purchase!
Instructions made easy

Read instructions or watch the easy-to-follow video. Scan code or visit byjasco.com/51766i
Register your product

Receive exclusive deals and register your product. Scan code or visit byjasco.com/deals
Like our product? Leave a review on your favorite retailer’s website or amazon.com.
Have Problems? Let us know how we can help. Call 1-800-654-8483 between 7 AM-8 PM, M-F, Central Time.

TOOLS NEEDED

• Pencil

• 1 Phillips-head screwdriver

• Electric drill
• Safety glasses
• 1/16in. drill bit (softwoods), 3/32in. drill bit (hardwoods)

INSTALLATION

SURFACE MOUNTING

Step 1: Choose a mounting location
Ensure the 5ft. power cord will reach the nearest 120VAC outlet. The chosen mounting location should be indoors, dry, and able to support fixtures.

Step 2: Remove the mounting plate
Remove the mounting plate from the rear of light fixture by firmly pushing it towards power cord — pull to remove.

Step 3: Mark screw locations
Hold the mounting plate in chosen mounting location. With a pencil, mark each screw’s location.

Step 4: Pre-drill holes
Drill pilot holes for screws using pencil markings for guidance. Use a 1/16in. (1.5mm) drill bit for soft woods and a 3/32in. (2.4mm) drill bit for hardwoods.

Step 5: Install the mounting plate
Hold the mounting plate in place. Use a #1 Phillips-head screwdriver and included screws to secure it into place — do not overtighten.

Step 6: Mount fixture
Align keyholes on the fixture with posts on the mounting plate. Slide fixture until it clicks into place.

Step 7: Connect to power
Insert attached 5ft. power cord into the nearest 120VAC receptacle.

DESKTOP MOUNTING

Remove mounting plate and set fixture on desk or table with rubber feet in contact with the surface. The ideal placement is the back edge of the desk or against a wall with the lens facing away from you.

OPERATION

BRIGHT-SELECT SWITCH
Use LOW/OFF/HIGH switch to change between low-level white light and high-level white light.
USB CHARGING
Both ports share 2.4 Amps of total output — fully charge a single tablet or two smartphones.

SPECIFICATIONS

• Electrical Ratings: 120VAC 60HZ 0.33A 39.6W
• USB Ratings: 2.4A / 5V / 12W
• LED Light Lumens: 503lm
• LED Light Watts: 7.8W
• LED Light Lumens/Watt: 64.5lm/W
• LED Light CRI: 97
• LED Light CCT: 3000K

SAFETY INSTRUCTIONS

Read and follow all safety instructions

• This product may represent a possible shock or fire hazard if improperly installed. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC).
• Consult a local licensed electrician or electrical contractor if you are not sure about installing the fixture yourself.
• Do not attempt to install the fixture while plugged in.
• Injury to persons and damage to the fixture and/or mounting surface may result if the fixture is pulled from the surface. To reduce the likelihood of such injury or damage, mount to a surface that is mechanically sound.
• Never use an extension cord unless the plug can be fully inserted. Do not alter the plug.
• Not to be used with a dimming circuit or any other electronically switched control.

CARE AND MAINTENANCE

• Do not use paints, solvents, chemicals or harsh abrasives on this light fixture.
• Clean only with a dry soft cloth.
• Do not use if there is any damage to the light or power cord insulation. Inspect periodically

FCC STATEMENT

Suppliers Declaration of Conformity | Model #: 51766 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING! RISK OF ELECTRIC SHOCK

• DO NOT USE IN WET LOCATIONS.
• USE INDOORS ONLY.
• USE ONLY INSULATED STAPLES OR PLASTIC TIES TO SECURE THE CORDS.
• ROUTE AND SECURE THE CORDS SO THAT THEY WILL NOT BE PINCHED OR DAMAGED.
• NO SERVICEABLE PARTS.
• NON-REPLACEABLE LEDS.
• LED LIGHT OUTPUT IS STRONG ENOUGH TO INJURE HUMAN EYES. PRECAUTIONS MUST BE TAKEN TO PREVENT LOOKING DIRECTLY AT THE LEDS WITH
• UNAIDED EYES FOR MORE THAN A FEW SECONDS.

RISK OF FIRE

• NOT INTENDED FOR ILLUMINATION OF AQUARIUMS.
• NOT INTENDED FOR USE ABOVE STOVES, COOKTOPS, SINKS OR OTHER HEAT-PRODUCING APPLIANCES, SUCH AS COFFEE MAKERS, TOASTERS, OR TOASTER OVENS.
• NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.
• NOT INTENDED FOR SURFACE INSTALLATION INSIDE OR ON TOP OF BUILT-IN FURNISHINGS SUCH AS KITCHEN CABINETS, CHINA CABINETS, OR TROPHY CASES.
• DO NOT CONCEAL POWER SUPPLY CORDS OR LINKING CORDS INSIDE A WALL, CEILING, SOFFIT, KITCHEN CABINET, OR SIMILAR PERMANENT STRUCTURE.
• DO NOT RUN THE POWER SUPPLY CORD OR LINKING CORDS THROUGH HOLES IN WALLS, CEILINGS, OR FLOORS.

Support

Coordinate and the Coordinate logo are registered trademarks owned by Jasco Products Company LLC. MADE IN CHINA Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114 This product comes with a 3-year limited warranty. Visit www.cordinateme.com for warranty details. Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.

References

• . Spend less. Smile more.
• YouTube
• Product Registration
• LED Lighting
• Recycling Matters at Jasco
• Jasco
• Cordinate

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>