Ring Range Extender EU 4AR1E9-0EU0 Manual
- June 8, 2024
- Ring
Table of Contents
- Ring
- Range Extender EU
- SKU: 4AR1E9-0EU0
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Configuration Parameters
- Technical Data
- Supported Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Ring
Range Extender EU
SKU: 4AR1E9-0EU0
Quickstart
This is a
secure
Repeater
for
.
Please make sure the internal battery is fully charged.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
Range Extenders extend the signal from your Alarm Base Station to all its components, so you can make sure your entire system stays online – Requires the Ring Alarm Security Kit.The Ring Extender is a Z-Wave range extender with battery backup. It is aSecurity Enabled Z-Wave Plus Product and requires a security-enabled Z-Wave Plus controller to make use of all of its features. It will repeat Z-Wave commands from all nodes in the network, from any certified Z-Wave device manufacturer. Any non-battery powered Z-Wave device will also repeat signals in a Z-Wave network.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1| 5| Group 1 is the Lifeline group, which can hold five devices. The Range
Extender repeats all signals it receives to this group.The Range Extender also
sends this group Battery Reports, Power Management notifications, and a Device
Reset Locally notification to remove itself from the Z-Wave network.
---|---|---
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock
further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus
56.
In case of a two byte value the same logic applies: Values greater than 32768
may
needed to be given as negative values too.
Parameter 1: Battery Report Interval
This parameter is the number of minutes between heartbeats. Heartbeats are
automatic battery reports on a timer after the last event.
Size: 1 Byte, Default Value: 70
SettingDescription
4 – 70| This parameter is the number of minutes between heartbeats. Heartbeats
are automatic battery reports on a timer after the last event.
---|---
Parameter 2: Supervision Timeout
The number of seconds waiting for a supervision report in response to a
supervision get from the sensor.
Size: 1 Byte, Default Value: 15
SettingDescription
5 – 50| The number of seconds waiting for a supervision report in response to
a supervision get from the sensor.
---|---
Parameter 3: Supervision Retry
Number of application level retries attempted for messages either not ACKed
or messages encapsulated via supervision get that did not receive a report.
Size: 1 Byte, Default Value: 1
SettingDescription
0 – 5| Number of application level retries attempted for messages either not
ACKed or messages encapsulated via supervision get that did not receive a
report.
---|---
Parameter 4: Supervision Back Off
The number base seconds used in the calculation for sleeping between retry
messages.
Size: 1 Byte, Default Value: 5
SettingDescription
1 – 60| The number base seconds used in the calculation for sleeping between
retry messages.
---|---
Parameter 5: Supervision Battery Report
The number of battery report messages sent before being encapsulated in
supervision.
Size: 1 Byte, Default Value: 5
SettingDescription
0 – 31| The number of battery report messages sent before being encapsulated
in supervision.
---|---
Parameter 6: Build Number
The Jenkins build number for this FW
Size: 4 Byte, Default Value: 0
SettingDescription
0 | The Jenkins build number for this FW |
---|
Technical Data
Hardware Platform | ZM5101 |
---|---|
Device Type | Repeater |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 3.05 |
Z-Wave Version | 6.81.03 |
Certification ID | ZC10-19106784 |
Z-Wave Product Id | 0x0346.0x0401.0x0202 |
Color | White |
Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Battery
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Notification V8
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>