HILTI HVU-TZ Capsule Adhesive Anchors Instruction Manual
- June 8, 2024
- HILTI
Table of Contents
HILTI HVU-TZ Capsule Adhesive Anchors
PARTS
- Hammer drilling
- Hollow drill bit
- Static loads
- Dynamic loads
HOW CAN IT USE
- Temperature of concrete
- Loosen setting adapter
- Curing time
- Push-through installation
- Pre setting
PAIR 1 AND IT USING
PAIR 2 AND IT USING
PAIR 3 AND IT USING
Read the instructions for use before using the capsule in order to obtain a fully functional anchor fastening. The concrete must have a min—compressive strength of 15 N/mm² (2000 psi).
- Use only undamaged capsules. Observe the capsule expiration date.
- Remove drilling dust and standing water from the bottom of a hole with air jet. Contaminated concrete (oil, bitumen, chemicals) can reduce the loading capacity.
- Steadily drive the threaded rod into the capsule with the rotary hammering action at 250 to 1000 r.p.m. , while applying moderate pressure and using a pushed-on or screwed-on setting tool. Switch off the machine immediately when the capsule embedment depth is reached.
- The hammering action must be switched on when setting all sizes.
- After the threaded rod has been set, the annular space must be filled entirely with adhesive right up to the surface of the concrete. If no glue emerges, the anchor fastening may not be used.
- DO NOT DISTURB the anchorage including removal of screwed-on setting tools until the time trel has passed. (Page 3 of the instruction booklet.)
- Tighten the anchor with a torque wrench and load it only after the time tcure has passed.
Hilti accepts no liability for damage resulting from failure to observe the installation instructions, use of anchors of inadequate size, installation in base materials with insufficient load-bearing capacity or incorrect use of the product.
Safety regulations
Danger Restricted to professional users. Contains 2-Propenoic acid, 2-methyl-, monoester with 1,2-propanediol; 2-Propenoic acid, 2-methyl-, 1,4-butanediol ester; dicyclohexyl phthalate; dibenzoyl peroxide; May cause an allergic skin reaction.May damage the unborn child. Toxic to aquatic life with long-lasting effects. Wear eye protection, protective clothing, and protective gloves. Do not get in eyes, on skin, or on clothing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: Wash with plenty of water. If eye irritation persists: Get medical advice/attention. If skin irritation or rash occurs: Get medical advice/attention.
Expiry date: See the date printed on the sales packaging (box).
Conditions for transport and storage:
Keep in a cool, dry and dark place between 5 °C to 25 °C / 41 °F to 77 °F.
Disposal instructions:
Unusable foil capsules e.g. if expiry date has been exceeded, should be
disposed of as hazardous waste material under observance of the official
regulations. EAK code no.: 20 01 27 or 08 04 09
Hilti (Gt. Britain) Ltd., 1 Trafford Wharf
Road, Trafford Park
GB-M17 1BY Manchester
Tel +44 161 886 1000
US Hilti, Inc. Legacy Tower, Suite 1000
7250 Dallas Parkway TX 75024
Plano – USA T +1 9724035800
US Hilti, Inc. Legacy Tower, Suite 1000
7250 Dallas Parkway TX 75024
Plano – USA T +1 9724035800
Made in Germany
www.hilti.group Printed in Germany © 2022
Hilti = registered trademark of Hilti Corporation, Schaan, L Right of
technical changes reserved S.E. & O.
15
Hilti AG FL-9494 Schaan Hilti Werke
0672-CPR-0047
ETA-03/0032 Notified body 0672
ETAG 001-1, -5
Option 1 www.hilti.group
21
Hilti AG
FL-9494 Schaan Hilti Werke
2873-CPR-201-69
ETA-17/0200 Notified body 2873
EAD 330250-00-0601
www.hilti.group
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>