danalock Universal Module V3 User Manual
- June 8, 2024
- danalock
Table of Contents
Universal Module V3
Specifications
| Operating voltage range | 12-24 V DC |
|---|---|
| Current consumption (at 24V) | 100 mA |
| Number of relays | 2 |
| Type of relays | Potential-free contacts (NO/NC) |
| Max relay voltage | 48 V |
| Bluetooth® range | 5 – 10 meters |
Wiring
Set up your Universal Module according to this schematic.
Use relay 1 before relay 2 if possible.
Click commands
You can configure the Universal Module via the button found in the small hole
on the module. When you get to the setting you want, wait for 5 seconds and
the Universal Module will react. If you make a wrong number of clicks, just
stop at an unmarked number of clicks and wait for 5 seconds. The LED will
flash red.
| Clicks | Color | Activity |
|---|---|---|
| 1 | Green | Inclusion/exclusion mode |
This command is for se ting up the Universal Module with a smart home gateway
such as Z-Wave. The Universal Module will respond by blinking green. Now the
module is in inclusion/exclusion mode and you have 30 seconds to pair or
unpair it with a gateway.
10| I Red| I Reset the Danalock
Resets all settings on the Universal Module. The Universal Module will respond
by blinking red.
LED signals
| LED mode | LED color | Status indication |
|---|---|---|
| 3 sec constant white | Power on | |
| Constant purple | Firmware update activated | |
| Blinking blue light | Settings changed | |
| 5 sec blinking white light | Identify | |
| 5 sec constant red | Factory reset | |
| 5 sec constant green followed by green blinks | Inclusion/exclusion mode |
activated
Simple Guidelines
Please follow these guidelines when confi guring, using or recycling the Universal Module V3. Violating these guidelines may be dangerous, illegal or otherwise detrimental. Further detailed information is provided in this manual.
Terms of use
This equipment design is primarily for indoor use mounted on a standard garage
door motor. Use only Danalock approved accessories for the Universal Module
V3, and compatible products, and do not operate the Universal Module V3 where
wireless radio communication is prohibited. Like hospitals, buildings near
blasting sites etc.
Do Not Operate Where Prohibited
Do not allow the Universal Module V3 unit to operate wherever wireless radio
communication use is prohibited or when doing so may cause interference or
danger as the Universal Module V3 cannot be turned off after installation.
Device Operation and human exposure to electromagnetic fields
The Universal Module V3 unit is a low power radio transmitter and receiver.
Periodically the Universal Module V3 wakes up either due to activity or by a
timer. When it is ON, it receives and sends out radio frequency (RF) signals
for a short period of time.
Specifi c Human Absorption Ratio (SAR)
The Universal Module V3 unit is not intended for handheld use or to be worn on
the body. A minimum separation of eight (8”) inches (20 cm) is to be
maintained between the Universal Module V3 and any persons body.
Interference
Like all wireless devices, the Universal Module V3 may encounterelectrical
interference that may aff ect its performance. The Universal Module V3 is
tested and certified according to international and European standards. The
performance hereof ensures correct operation in the presence of
electromagnetic interference and/or electrostatic discharge.
Category of use
The Universal Module V3 unit is an electronic port lock controller meant for
garage doors mounted in conjunction with the standard garage door motor.
Security for electrical functions
The Universal Module V3 has no indications, sound alarms in case of a
connected lock malfunction.
Security for electrical manipulation
The Universal Module V3 is tested compliance to the EMC requirement laid out
in the 2014/53/EU directive. The performance hereof ensures correct operation
in the presence of electromagnetic interference and/or electrostatic
discharge.
Children
The Universal Module V3 series and its accessories are not used to solicit
data from or market to children
Warranty
Danalock ApS products are covered by a limited manufacturer warranty. The
Danalock ApS warranty is limited to the warranty rules and legislation present
in each country. The warranty only covers manufacturing faults. The warranty
does not cover misuse, wrong installation or damage due to a faulty
installation or wrong maintenance.
The invoice act as the proof of warranty, so please keep it as reference for
any warranty complaints.
Qualifi ed Service
The Universal Module V3 contains no user serviceable or replaceable parts.
Non-functioning units must be returned to an authorized service center for
repair or replacement.
Technical Assistance
If you have a problem and cannot find the information you need in the product documentation, please contact Danalock ApS at support@danalock.com. Please have the following information ready:
- Serial number (preferred), MAC address or alias of the lock
- Username used when registering / installing the lock
- Username used when getting the error (ifdiff erent username)
- Time of incident
CE and UKCA mark
The Universal Module V3 complies with the essential requirements of the RED
directive 2014/53/EU and Radio Equipment Regulations 2017 – UK SI 2017 No.
1206 with respect to radio spectrum, EMC, Health and safety. EU Certifi cate
and Declaration of conformity (DOC) can be downloaded from the webpage:
https://danalock.com/legal/certificates/
Danalock Universal Module V3-BT
Product specifications
| Supply voltage | 12-24 V DC | |
|---|---|---|
| Temperature range | Active operating mode | -20°C to +40°C |
| Storage | 5°C to +50°C | |
| Mechanical specifications | Dimensions (W x H x L) | 17 mm x 38 mm x 35 mm |
| Weight | 14 g | |
| Material | Plastic | Black PP |
| Radio interfaces | Bluetooth LE | Max.5.1 dBm |
E.I.R.P
US and Canada certifi cation marks
This device contains radio transmitters that comply with CFR 47 part 2.1091,
part 15.207, Part 15.247 of the FCC rules and with RSS-GEN, RSS-102 and
RSS-247 of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The device complies with Part 15 of the FCC rules and with Industry Canada
license exempt standard(s). Operation is subject to the following two
conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modifi cations made to this equipment not expressly approved by
Danalock Aps may void the FCC authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and RSS-102:
With respect to radiofrequency radiation exposure Information it is declared
that this equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
FCC part 15B note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
Japan
The product is approved in Japan with the certifi cate ID n°: [R] 204-720646
This device is granted pursuant to the Japanese Radio Law
This device should not be modifi ed (otherwise the granted designation number
will become invalid)
Danalock Universal Module V3-BTZE
Product specifications
| Supply voltage | 12-24 V DC | |
|---|---|---|
| Temperature range | Active operating mode | -20°C to +40°C |
| Storage | 5°C to +50°C | |
| Mechanical specifications | Dimensions (W x H x L) | 17 mm x 38 mm x 35 mm |
| Weight | 14 g | |
| Material | Plastic | Black PP |
| Radio interfaces | Bluetooth LE | Max.5.1 dBm |
E.I.R.P
Z-Wave| Max 8.0 dBm E.I.R.P
Danalock Universal Module V3-BTZH
Product specifications
| Supply voltage | 12-24 V DC | |
|---|---|---|
| Temperature range | Active operating mode | -20°C to +40°C |
| Storage | 5°C to +50°C | |
| Mechanical specifications | Dimensions (W x H x L) | 17 mm x 38 mm x 35 mm |
| Weight | 14 g | |
| Material | Plastic | Black PP |
| Radio interfaces | Bluetooth LE | Max.5.1 dBm |
E.I.R.P
Z-Wave| Max 0 dBm
E.R.P
Z-Wave country specific setting
Operating Frequency (Japan)| 922.50 MHz (100 kbps), 923.90 MHz (100 kbps),
926.30 MHz (100 kbps)
Operating Frequency (AUS)| 921.42 MHz (9.6 kbps), 921.40 MHz (40 kbps), 919.80
MHz (100 kbps)
AUS/NZ
The product complies with the AS/NZS 4268 requirements for Bluetooth LE
transceiver and Z-wave 1Tx/1RX (receiver class 2/3) applications under the
Radiocommunications Act 1992; Radio communications (Low Interference Potential
Devices) Class License 2015 compilation 2016 May 4. The product complies with
the requirements of the relevant standards under Section 134 (1) (g) of the
New Zealand Radiocommunications Act 1989, by the Supplier’s Declaration of
Conformity (SDOC)
Japan
The product is approved in Japan with the certifi cate ID n°: [R] 204-720649
This device is granted pursuant to the Japanese Radio Law (
This device should not be modifi ed (otherwise the granted designation number
will become invalid)
The product complies with the ARIB STD-T108 for Z-wave applications.
Danalock V3 BTZU
Product specifications
| Supply voltage | 12-24 V DC | |
|---|---|---|
| Temperature range | Active operating mode | -20°C to +40°C |
| Storage | 5°C to +50°C | |
| Mechanical specifications | Dimensions (W x H x L) | 17 mm x 38 mm x 35 mm |
| Weight | 14 g | |
| Material | Plastic | Black PP |
| Radio interfaces | Bluetooth LE | Max.5.1 dBm |
E.I.R.P
Z-Wave| 89.4 dBpV/m @ 3m (Average
US and Canada certifi cation marks
This device contains radio transmitters that comply with CFR 47 part 2.1091,
part 15.207, Part 15.247 of the FCC rules and with RSS-GEN, RSS-102 and
RSS-247 of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The device complies with Part 15 of the FCC rules and with Industry Canada
license exempt standard(s). Operation is subject to the following two
conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modifi cations made to this equipment not expressly approved by
Danalock Aps may void the FCC authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and RSS-102:
With respect to radiofrequency radiation exposure Information it is declared
that this equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC part 15B note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Regulatory labeling:
The UMV3-BTZU product are regulatory compliant to the following regulation
(USA/Canada):
FCC ID: 2ADSH-UMV3BTZU
IC:12588A-UMV3BTZU
Danalock ApS
Gammel Stillingvej 427C
8462 Harlev, DK
+45 4242 8122
info@danalock.com
www.danalock.com
References
- Danalock · Danalock V3 - The Smart Home Enabler
- Danalock · Danalock V3 - The Smart Home Enabler
- Certificates · Danalock
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>