YARBO WF1 WiFi Module User Manual
- June 8, 2024
- YARBO
Table of Contents
YARBO WF1 WiFi Module
FCC ID: 2A9JF-HY0915-VARBO
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This modular must be
installed and operated with a minimum distance of 20 cm between the radiator
and user body. If the FCC identification number is not visible when the module
is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed
module. This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: 2A9JF-HV0915-YARBO Or Contains FCC ID:
2A9JF-HV0915-YARBO”
When the module is installed inside another device, the user manual of the host must contain below warning statements;
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product.
Any company of the host device which install this modular with limit modular
approval should perform the test of radiated emission and spurious emission
according to FCC part 15C: 15.247 and 15.209 requirement, Only if the test
result comply with FCC part 15C : 15.247 and 15.209 requirement, then the host
can be sold legally.
IC:29777-HY1031YARBO
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation,
Science and Economic Development Canada’ s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 29777-HY1031 YARBO” any similar wording that expresses the same meaning may be used.
Common Information
Product Name: Yarbo Wi-Fi Module
Model No.(EUT): WFl
Trade mark: Yarbo
Product Type: Mobile Portable Fix Location
Operation Frequency: IEEE 802.llb/g/n(HT20): 2412MHz to 2462MHz
IEEE 802.lln(HT40): 2422MHz to 2452MHz
Modulation Type: IEEE for 802.llb:DSSS(CCK,DQPSK,DBPSK)
IEEE for 802.llg:OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE for 802.lln(HT20/HT40): OFDM (64QAM, 16QAM,QPSK,BPSK)
Number of Channel: IEEE 802.llb/g, IEEE 802.lln HT20: 11 Channels
IEEE 802.lln HT40: 7 Channels
Channel Separation: 5MHz
Antenna Type: FPC Antenna
Antenna Gain: ANT1:l.82dBi,ANT2:l.82dBi
Function SISO 2×2 MIMO
Beamforming TPC
Power Supply: DC 12V
Test Voltage: DC 12V
Notice
- The module is limited to OEM installation ONLY
- The OEM integrators is responsible for ensuring that the end-user has no manual instructions to remove or install module
- The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b)
- The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations
Installation and operation instruction
-
The computer searches for the wireless network connection of the wireless router (the default wireless name is the router model + MAC followed by 4bit), and then click the ‘Connect’ button to establish a connection, the wireless password is: 12345678.
-
When your computer network icon shows connected, it means that the IP address has been successfully obtained. To ensure successful connection, please use Ping command confirmation.
Method: Open the cmd command line window and execute the Ping command: Ping 192.168.10.1. -
Next you will land on the router web management setup page.
-
Enter “http://192.168.10.l” in the address bar of the web browser, and enter the login user name and password in the pop-up box.
-
When logging in for the first time, please enter the default username: admin, password: admin.
-
Success.
Antenna installation requirements
Step 1
Place the antenna in the desired direction.
Step 2
Finished.
Main features
Intelligent anti-dropout, support online detection, online maintenance, automatic redial of dropped calls, ensure that the device is always online
RS232 serial port support
Local network PHP browsing with remote synchronisation of locally stored
content
Supports serial data serial TCP/UDP transparent data transfer or AT command
transfer
SMS control of routing online and offline, SMS notification of routing status
Support for VPN secure tunneling, including PPTP, L2TP
Complete and robust router with multiple Internet access options: auto-assign,
assigned IP, PPPOE
IPTABLES firewall support, various network protocols
Dynamic DDNS support: peanut shell, 881P and dyndns domain providers are
supported
Support serial local TFTP, web software upgrade
WiFi parameter
Basic parameter| WIFI switch support SSID broadcast switch
support
---|---
MAX speed: 300Mbps Operating frequency band: single frequency 2.4GHz
2.4GHz
Channel selection: channel 1-11
Wireless mode: 11b/g/n/, 11bg mixed, 11bgn mixed(Def)
Support speed: 300Mbps (Max)
No. of users| Up to 32 simultaneous wireless users
Safety parameters| Supports WAP-PSK/WPA2-PSK authentication type
Supports 64/128-bit WEP encryption support TKIP, CCMP/AES algorithm encryption
Transmission distance| Outdoor unobstructed/open, coverage up to 100m
Interface parameters
| WAN port | 1 x 10/1 DOM adaptive WAN port Built-in isolation |
|---|
Support for Auto Rollover (Auto MDI/ MDIX) Support for
PPPOE
LAN port| 1 x 10/1 00M adaptive LAN port
Built-in 1.5 KV electromagnetic isolation protection
Support for Auto MDI/ MDIX
Serial port| 1 x RS232 serial port
Power connector| Standard DC connection 12V /1-2A
Antenna interface| 2 x antenna interface (2 x WIFI antennas)
Indicator light| 2x indicator lights (SYS light, WiFi light)
System parameters
| CPU | MIPS CPU, MT7628 Dual Core 580Mhz |
|---|---|
| MMU | The CPU has its own MMU memory management unit, which can effectively |
prevent the system from abnormalities caused by memory overflow
FLASH| 64 Mbits of memory for easy storage of programs and data
DDR2| Large 512Mbits cache for easy system speed
Other parameters
Supply voltage| Wide voltage design DC 7V – 35V power supply Built-in power
reverse protection, overvoltage and overcurrent protection
---|---
Power supply as standard| 9V/12V 1.0A-2.0A
Outer shell| Metal housing, radiation-proof, interference-resistant,
lightning-proof design, safe isolation of the housing from the system,
suitable for harsh industrial control areas
Product size| 754212.5mm
Package size| 46534575 mm (Pack of 100 pieces)
Product net weight| 15g
Gross product weight| 15g
Operating temperature| ‘-30°( ~ +70°(
Storage temperature| ‘-40°( ~ +85°(
Humidity| 95pw (no condensation)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>