HILTI NCR 120 C-22 Cordless Hydraulic Crimpers Instruction Manual

HILTI NCR 120 C-22 Cordless Hydraulic Crimpers

Information about the documentation

About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.

Explanation of symbols used
Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:

DANGER!

• Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING!

• Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION!

• Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property.

Symbols in the documentation
The following symbols are used in this document:

• Read the operating instructions before use.
• Instructions for use and other useful information
• Dealing with recyclable materials
• Do not dispose of electric equipment and batteries as household waste

Symbols in the illustrations
The following symbols are used in illustrations:

• These numbers refer to the corresponding illustrations found at the beginning of these operating instructions
• The numbering reflects the sequence of operations shown in the illustrations and may deviate from the steps described in the text
• Item reference numbers are used in the overview illustrations and refer to the numbers used in the product overview section
• This symbol is intended to draw special attention to certain points when handling the product.

Product-dependent symbols

Symbols on the product
The following symbols are used on the product:

Product information

products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed aboutthe possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are printed on the rating plate.

• Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Crimping tool| NCR 120-22

NCR 120C-22

---|---
Generation| 02
Serial no.|

Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

Safety

General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase therisk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged,have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified rangemay damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Drill/driver safety warnings

• Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Additional safety precautions for screwdrivers
Personal safety

• Use the product only when it is in perfect working order.
• Never tamper with or modify the tool in any way.
• Use the auxiliary grips supplied with the power tool. Loss of control can cause personal injury.
• Always hold the tool firmly with both hands on the grips provided. Keep the grips clean and dry.
• Do not touch rotating parts – risk of injury!
• Wear suitable protective glasses, a hard hat, ear protection, protective gloves and light respiratory protection while using the power tool.
• Wear protective gloves also when changing the tool. Touching the accessory tool can result in cuts and burns.
• Wear eye protection. Flying fragments can injure the body and eyes.
• Before starting work, check the hazard class of the dust that will be produced when working. Use an industrial vacuum cleaner with an officially approved protection class in compliance with the locally applicable dust protection regulations. Dust from materials such as lead-based paint, certain types of wood and concrete/masonry/stone containing quartz, minerals or metal can be harmful to health.
• Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory or other diseases among operators or bystanders. Certain kinds of dust are classified as carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning (chromate, wood preservative). Only specialists are permitted to handle material containing asbestos.
• Take breaks and do physical exercises to improve the blood circulation in your fingers. Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands and wrists.

Electrical safety

• Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the power tool may give you an electric shock if you damage an electric cable accidentally.

Power tool use and care

• Immediately switch off the power tool if the accessory tool jams. The power tool might twist off-line.
•  Wait until the power tool stops completely before you lay it down.

Battery use and care

• Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion batteries.
• Do not expose batteries to high temperatures, direct sunlight or fire.
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
• Do not use or charge batteries that have suffered the mechanical impact, have been dropped from a height or show signs of damage. In this case, always contact your Hilti Service.
• If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable location, well away from flammable materials, where it can be kept under observation and allowed tocool down. In this case, always contact your Hilti Service.

Description

Product overview 1

1. Crimping-die release button
2. Crimping head
3. Attachment eye
4. Piston return switch
5. Control switch
6. Side handle
7. Servicing and fault indicator
8. Battery protection
9. Battery
10. Battery release button
11. Battery status indicator
12. Work-area light
13. Crimping die

Intended use
The product described is a hand-held cordless electric tool, equipped with a clutch, for use in drywall installation work. The power tool is designed for driving and removing screws in drywall installation work. Drywall screws with a length of up to 55 mm and a diameter of up to 4.2 mm can be used. Do not use the product to work with materials hazardous to the health (e.g. asbestos)

• Use only Hilti Li­ion batteries of the B 22 series with this product.
• Use only Hilti battery chargers of the C4/36 series for charging these batteries.

Status indicator
The status indicator provides information about the status of the fastening tool.

Recharge the battery.

If the LED again starts quick-flashing after the bat- tery has been charged, consult Hilti Service.

One (1) LED quick-flashes yellow| The Li-ion battery or the product in which it is in- serted is overloaded, too hot or too cold, or experi- encing some other fault.

Bring the product and the battery to the recom- mended working temperature and do not overload the product when it is in use.

If the message persists, consult Hilti Service.

One (1) LED shows yellow| The Li-ion battery and the product in which it is inserted are not compatible. Consult Hilti Service.
One (1) LED quick-flashes red| The Li-ion battery is locked and cannot be used. Consult Hilti Service.

Indication of battery charge status
When one of the battery release buttons is pressed, the display indicates the battery’s state of charge. Reliable indication of the charge status is not possible while a fastener is being driven or immediately
after a fastener is driven.

The battery can remain in use.
All LEDs show in sequence, followed by one (1) LED quick-flashing yellow.| The check to ascertain the battery’s state of health did not complete. Repeat the procedure, or consult Hilti Service.

Technical data

Noise information and vibration values

The sound pressure and vibration values given in these instructions have been measured in accordance with a standardized test and may be used to compare one power tool with another. They may be used for a preliminary assessment of exposure. The data given represents the main applications of the power tool. However, if the power tool is used for different applications, with different accessories or is poorly maintained, the data may vary. This may significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This may significantly reduce exposure over the total working period. Set out additional safety measures to protect the operator from the effects of noise and/or vibration, such as: Maintaining the power tool and accessories, keeping the hands warm, reorganizing of work patterns.
Noise and vibration information (measured in accordance with EN 60745-216)

The data given represent the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.

Noise values

Vibration values

Battery

Preparations at the workplace

CAUTION
Risk of injury by inadvertent starting!

• Before inserting the battery, make sure that the product is switched off.
• Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery.

Inserting the battery
CAUTION
Risk of injury by short circuit or falling battery!

• Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
• Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.
2. Push the battery into the battery holder until it engages with an audible click.
3. Check that the battery is seated securely.

Removing the battery

1. Press the release buttons on the battery.
2. Pull the battery out of its holder in the device.

Fitting the belt hook (optional) 2
The belt hook enables you to attach suitable power tools to your belt. It can be fitted to allow attachment on the left or right side of the body.
CAUTION
Risk of injury by falling power tools!

• Check that the belt hook is fitted securely before beginning work.

1. Fit the belt hook.
2. Attach your power tool to the belt hook.
3. Check that belt hook and power tool are secure.

Working safely with the belt hook and universal hook

• Before beginning work, make sure that the belt hook and universal hook are securely attached to the screwdriver.
• Use the universal hook only when necessary. Lay the screwdriver down in a safe place when it is not in use for a long period.

Changing the accessory tool. 3

1. Pull the depth gauge away from the power tool, releasing the snap-on connection.
2. Push the chuck towards the screwdriver, turning the chuck slightly at the same time, and then hold it in this position.
3. Remove the accessory tool with your other hand.
4. Insert the desired accessory tool in the chuck, pushing it into the screwdriver as far as it will go

Forward / reverse 4
The control switch is locked when the forward/reverse switch is in the middle position (safety lock).

• Set the forward/reverse selector switch to forward or reverse rotation.

Driving a fastener 5
WARNING
Risk of injury by incorrect handling and/or splintering material!

• Risk of driving a nail through your hand! Always use both hands to operate the product! Always hold the product firmly with your second hand as illustrated.
• Never press the nosepiece of the fastening tool against your hand or any other part of the body! By unintentionally triggering a driving operation, can cause severe injury.
• Wear personal protective equipment and always wear protective glasses and protective gloves. Other persons in the vicinity must also wear eye protection and a hard hat. When fasteners are being driven, there is a risk of injury to the body and eyes caused by material splintering off the working surface and also if there are foreign bodies in the area of the fastener guide.
• Never attempt to clear malfunctions of the tool by continuing to trigger the tool!

Care and maintenance

WARNING
Risk of injury with the battery inserted!

• Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

Care of the Li­ion batteries

• Keep the battery free from oil and grease.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these may attack the plastic parts.
• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired immediately by Hilti Service?
• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.Hilti.group.

Transport and storage of cordless tools
Transport
CAUTION
Accidental starting during transport!

• Always transport your products with the batteries removed!
• Remove the battery.
• Never transport batteries in bulk form (loose, unprotected).
• Check the tool and batteries for damage before use after long periods of transport.

Storage
CAUTION
Accidental damage caused by defective or leaking batteries!

• Always store your products with the batteries removed!
• Store the tool and batteries in a place that is as cool and dry as possible.
• Never store batteries in direct sunlight, on heating units or behind a window pane.
• Store the tool and batteries in a place where they cannot be accessed by children or unauthorized persons.
• Check the tool and batteries for damage before use after long periods of storage.

Troubleshooting

If a problem occurs, always observe the status indicator of the battery. See the section headed Status indicators of the Li­ion battery. If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by yourself, contact Hilti Service

state of charge of the battery is too low to allow a complete op- erating cycle.| ▶| Change the battery and charge the empty battery.
Red LED => flashes at long intervals and a warning tone is emitted.| Crimping / pressing pressure not achieved (tool was used incor- rectly).| ▶| Make sure that the tool is used correctly and check the crimped

/ pressed part if unsure.

Red LED => lights briefly and no warning tone is emitted.| Product overheated.| ▶| Allow the product to cool down.
LEDs of the battery show nothing| Battery faulty.| ▶| Contact Hilti Service.

Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
Battery disposal
Improper disposal of batteries can result in health hazards from leaking gases or fluids.

• DO NOT send batteries through the mail!
• Cover the terminals with a non-conductive material (such as electrical tape) to prevent short-circuiting.
• Dispose of your battery out of the reach of children.
• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.
• Do not dispose of power tools, electronic equipment or batteries as household waste!

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

• Do not dispose of power tools, electronic equipment or batteries as household waste!

Manufacturer’s warranty

• Please contact your local Hilti representative if you have questions about the warranty conditions.

Further information

For more information on operation, technology, environment and recycling, follow this link: qr.hilti.com/manual?id=02321721 &id=2321723 This link is also to be found at the end of the documentation, in the form of a QR code.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>