ring Spotlight Cam Hardwired Kit Installation Guide
- June 9, 2024
- Ring
Table of Contents
ring Spotlight Cam Hardwired Kit Installation
IMPORTANT PRODUCT INFORMATION
Use Responsibly. Read all instructions and safety information before use.
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC
SHOCK, OR OTHER INJURY OR DAMAGE.
Small parts contained in the Spotlight Cam Hardwire Kit may present a choking
hazard to small children. Keep small parts away from children.
Terms of Service and Warranty
Use of the product is subject to your registration with Ring and your
agreement with the Terms of Service found at
www.ring.com/terms.
To review your warranty coverage, please refer to the enclosure inside this
box or visit www.ring.com/warranty.
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make
sure you dispose of, or recycle, your device in accordance with your local
laws and regulations. For information about recycling your device, go to
www.amazon.com/devicesupport.
WARNING: Risk of electrical shock.
Disconnect power at the fuse or circuit breaker before installing.
- Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source.
- Always follow electrical code standards when installing wired connections.
- If you are outside of North America, installation and wiring must be performed by a licensed electrician.
CAUTION: Risk of fire.
Do not install near combustible or flammable surfaces.
NOTICE
Do not connect this light fixture to a dimmer switch or timer. Must be
installed on a UL listed weatherproof electrical box.
What’s in the box?
-
Screwdriver & Phillips
Bit Use to install the box cover and tighten the security screw. -
Bag o’ Screws & Washers
Use four screws when mounting to a round electrical box, or two when mounting to a rectangular box. -
Wire Nuts
Use to secure and protect wire connections. -
Hanging Hook
Use to hold the weatherproof box cover in position as you install. -
Round Weatherproof Box
Cover Use to mount your Spotlight Cam on a round weatherproof electrical box. -
Rectangular Weatherproof Box
Covers (Vertical & Horizontal) Use to mount your Spotlight Cam on a 1-gang rectangular weatherproof electrical box. -
Wiring Harness and Mounting Nut
Use to attach your Spotlight Cam to your chosen weatherproof box cover, and connect it to your household wiring. -
Security Screw
Use to secure your Spotlight Cam to the box cover.
How it all fits together
Remove your Spotlight Cam from its base.
While holding the mounting base, turn Spotlight Cam to the left to disengage
it, and set the camera aside for now.
Mounting Styles: Wall
When mounting to a vertical wall, you’ll usually want the mounting port to
face downwards. Mounting Styles: Ceiling
If mounting to a horizontal surface, face the port in the direction you want
the camera to see.
Ensure that the electrical box you use is
weatherproof, including threaded plugs. Use sealant if necessary.
Installation Height and Motion Detection
Shut power off at the breaker.
If you don’t know where your breaker is or how to turn off power to your
electrical box, consult with a licensed electrician.
Remove your existing light or camera. (if applicable)
With power off at the breaker, remove your existing floodlight or camera from
the electrical box and disconnect the wires. If there is a bracket attached to
your electrical box, remove that as well.
Hang the box cover. Inspect the box to make sure water can’t get in. Then use the included hanging hook to hold the weatherproof box cover in place as you wire it in.
Connect the power wires.
Connect the black and white wires on the wiring harness to the black (hot) and
white (neutral) wires coming out of your electrical box.
- Use the included wire nuts to secure and protect the connections.
- The red wire is optional, and should only be connected if you wish to control other lights with your Spotlight Cam.
If you don’t have clearly colored black and white wires coming out of your electrical box, consult with a licensed electrician.
Auxiliary Light Control
Your Spotlight Cam has an advanced motion detection system. If you’d like
other lights (such as floodlights) to be triggered by the motion detector in
your Spotlight Cam, wire them according to this diagram.
Your connected lights also turn on when you manually enable your Spotlight Cam
lights in the Ring app.
Screw in the box cover.
Use the included screws to secure the box cover to the electrical box. Be sure
to add a metal washer, then a rubber washer to each screw before inserting.
Add the Security Screw.
Insert and tighten the security screw to lock your Spotlight Cam into the box
cover.
- Some round boxes may only take two screws. Seal unused holes in the cover with the included screws and nuts. Add a metal washer backed by a rubber washer to each side before tightening the nut.
Mount your Spotlight Cam.
Insert your Spotlight Cam into the box cover. Once it’s fully seated, turn to
the right to lock it in.
Turn on power at the breaker.
- Once your Spotlight Cam is installed, it’s time to turn power back on at the breaker.
- If the lights on your Spotlight Cam turn on, you’re all set!
- If not, turn power off at the breaker and check your connections.
Try it out!
After setup, tap the Live View button in the Ring app to see video from your
Spotlight Cam. If you have any problems, visit
ring.com/help.
White light flashing?
If the light on the bottom of your Spotlight Cam flashes or stays illuminated
after setup, this means it’s updating its internal software.
This update can take up to a few minutes. The light turns off when the update
is complete.
Adjust the camera angle
To ensure accurate motion detection, position your Spotlight Cam so the border
of the motion detector is parallel with the ground.
Tighten the side screw to secure the camera position.
For additional help, visit: ring.com/help Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer support numbers, visit:
ring.com/callus
1523 26th St.
Santa Monica, CA 90404
To review your warranty coverage, please visit
www.ring.com/warranty. © 2020 Ring LLC or its
affiliates. Ring, Always Home, and all related logos are trademarks of Ring
LLC or its affiliates.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>