VKI Technologies Eccellenza Momentum Coffee Maker Machine User Guide

VKI Technologies Eccellenza Momentum Coffee Maker Machine

in the box

1. Cut the two straps on the outside of the box.
2.  Lift the top part of the box over the machine.
3. Remove the four foam supports and remove the cup stand secured between the two upper supports. Do not discard the front support as it must be installed over the machine’s screen to protect it when transporting the machine.
4. With the help of a colleague, lift the coffee maker off the base of the packaging and place it onto a cabinet.

To prevent personal injury and/or damage to the equipment, never attempt to lift the equipment by yourself and never lift the equipment by placing your hand under the front door!

Remove shipping tape and protective film, and install accessories

1. Remove the keys and telemetry antenna from the cup stand.
2. The Eccellenza Momentum uses a multi­ position door lock that can unlock only the waste bin, or can unlock both the door and waste bin.
3. Install the telemetry antenna to the round connector at the top right corner on the rear of the machine.
4. connector at the top right corner on the rear of the machine.
5. Remove the blue shipping tape and protective film from the outside of the machine and from the stainless steel cup stand grill.

Installation Precautions

• This equipment is designed for indoor use only and must DfW be installed outdoors.U
• Installation of this equipment must comply with all local, state/provincial and federal codes and regulations. It is the sole responsibility of the installer to research and to comply with these codes and regulations.
• This equipment must be installed on a dedicated 120-Volt, 20-Amp outlet. Do not install other equipment on the same outlet/circuit.
• Ensure that the equipment is level and stable. This is done by adjusting the levellers (legs) at the bottom of the machine. Also, do not block any of the equipment’s ventilation ports.
• Do not use extension cords and power bars when connecting this equipment to a power source.
• Leave room at the rear of the equipment for the plumbing fitting and water hose, as well as for adequate ventilation. Leave ample room above the equipment to open and fill the product hoppers.
• Installation of this equipment must comply with all local, state/provincial and federal codes and regulations. It is the sole responsibility of the installer to research and to comply with these codes and regulations.
• Accessibility to shut-off valve(s) must be provided and explained to customer in the event water supply to brewing equipment must be shut off.
• For multi-unit locations whereby the main water conduit is supplying water to more than one unit (including water coolers). a separate in-line shut off valve must be installed onto each individual equipment unit.

Water Filter

We recommend the use of a high-quality water filter which eliminates most odors present inwater, and reduces the amount of particles entering the water tank. When installing a water filter, you must refer to the water filter manufacturer’s installation instructions.

Starting the Equipment

The main power switch for the Eccellenza Momentum is located at the rear, right side of the machine.
To switch the power ON, toggle the power switch to the ” I ” position. The Eccellenza Momentum goes through a quick initialization process, after which, it is ready to be used.

Fill the Coffee Bean and Powder Dispensers

1. Unlock and open the coffee bean dispenser lid.
2. Fill the three dispensers with coffee beans.
3. Open the main powder dispenser lid and remove the individual lid of the dispenser to be filled.
4. Fill each of the dispensers with powder.
5. Replace and close all of the product dispenser lids.

Checking the Water Temperature

To check the current water temperature in the hot water tank, remove and re- install the waste bin. The machine displays the water temperature in the lower center of the screen during re-initialization.

Initial Adjustments (using the Operator access code)

Set the Date and Time
Enter the set up of the machine and set the correct date and time. This is extremely useful when setting the Energy Savings features, tracking data that the equipment has collected and when reports are sent to the operator of the equipment. The date and time settings are found in the ‘General Settings’ menu.

Water Levels
The Eccellenza Momentum is factory preset to only dispense 12-oz, 16-oz, and 20-oz cups sizes. The water levels can be fine-tuned in the’ Setup’ menu.

Gram Throws
You may need to fine-tune the gram throws for the coffee blends and powder types you will be using in the equipment. This ensures that the equipment delivers the best tasting beverage possible.
Product settings are adjusted in the’ Setup’ menu.

Beverages
The Eccellenza Momentum is preset with all of the beverages and beverage options (such as cup sizes and strengths) enabled. Beverage options are set in the’ Setup’ menu.

Notifications
The Eccellenza Momentum can be configured to provide notifications about usage and consumption, counters, faults and messages, etc. To configure the’ Notifications’ feature, go to the’ Network’ menu.

Change PINs for the Operator and Administrator
To prevent unauthorized access to the Eccellenza Momentum programming, we highly recommend that you change the default PIN (Personal Identification Numbers) for both the Operator and Administrator. Both PIN numbers can be changed in the’ Security’ menu.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>