CALDWELL 1136235 Emax Pro BT Comms Earmuff Instructions

1136235 Emax Pro BT Comms Earmuff

The 1136235 Caldwell Emax Pro BT Comms is a new generation protective communication solution. With an integrated, pre-programmed analog  two-way radio, noise-cancelling microphone, and environment listening, the Caldwell Emax Pro BT Comms not only helps protect you against  hazardous noise, but also makes it easy to communicate in noisy environments and helps promote auditory situational awareness.

Hearing protection with built in two-way radio

Environmental-listening technology

Noise-cancelling boom microphone for clear speech transmission in noisy environments

Environmental-listening technology

 Function:

1. Ambient  noise  reduction  function  and  ambient  microphone  amplifier  limit  the ambient sound pressure to 82 dB.

2. Including 22 CTCSS/DCS channels. Each channel can be set with separate mute (CT).
   Squelch and other parameters.

3. Push-to-talk(PTT) or hands-free voice (vox) transmission capabilities.

4. Bluetooth music function and voice calling function.

5. Lithium battery powered.

There are 6 buttons on this side of earmuff,as shown in the picture:

1. [MENU] Long press to power on/off, short press to change mode
2. [VOL+] [VOL-] adjust volume;
3. [PTT] Useful only in intercom mode, press to talk;
4. [ CH+ ] [ CH- ] Useful only in intercom mode, for channel switching

Parameter setting:

1. Area: The number of frequency channels and other parameters will be different in different countries and regions.
2. Brightness: Screen backlight brightness.
3. Light Delay: No key operation, backlight off time.
4. CTCSS: Current channel mute setting of interphone. The same mute set in the same group can filter out interference.
5.  Voice Control :Intercom voice control function, all channels are effective, and the larger the number, the easier to start control.
6. Radio Power: Current channel power setting of walkie talkie.
7. Squelch Level: The current channel noise level of the walkie talkie. The larger the number, the less likely it is to be interfered.
8. Reset All: Restore all parameters to their original values.

Operation:

FRS MODE

1. Doudble click 1button, the display will show the icon as below:

2. Press “1” or “2” to the frequency signal channel to what you want. (e.g CH: 01)

3. Press and hold “3”(M) there is a “TX” will appear to the display screen.

4. Now you could talk in the microphone.
   NOTE: the receiver unit must be setup to the same frequency signal channel. There is a “RX” appear to screen at the same time. Means it is  working at the reciveing mode.

5. After finished the functions setup few seconds in FRS mode. There is a “LOCK” appears in the screen. That means you can not use “1” “2”   keys.
   If you want to changing the channel, you must press both “1” “2“ together for a second, the “LOCK” will disapper. Then you could change  the channel up or down.

6. You could press 2button to adjust volume, until you feeling the sound level in right place. The maxium volume sound level is 82 dB.

7. If you don’t want push “3”(M). The system for you delivery a “VOX” function. (setup information will later…)

Bluetooth MODE

1. Press”3”(M) until you see below icon.

2. Turn on your mobile, and setup Bluetooth to “ON”. You will see an “Onlyele” appears in the option device bar. Choice it and pairing it. Then  you will see below icon:

3. After bluetooth connected. You could play music in your mobile,

4. Adjust the volume by pressing the 2 button

5. place. The maxium volume sound level is 82 dB.

Ambient MODE

1. Press”3”(M) until you see below icon.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct  the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modififications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information

The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance Omm between the radiator & your body.

ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>