Shenzhen Caisu Technology F011 Ultrasonic Tooth Cleaner Instruction Manual
- June 4, 2024
- Shenzhen Caisu Technology
Table of Contents
Shenzhen Caisu Technology F011 Ultrasonic Tooth Cleaner Instruction Manual
- Thank you for purchasing our products
- Be sure to read this manual carefully before use and keep it safe for future reference.
- This product can only be used for personal dental cleaning at home, not available for any medical purpose.
Product description
Thank you for choosing this product as your oral health care assistant. Please check the product list shown below to check whether the relevant parts are available.
Product use
Warning
When turning on the scaler, do not point the metal cleaning head at sensitive
parts of the human body such as eyes, as well as power supplies, lamps and
other equipment. When the product is turned on, please touch the metal
cleaning head with your skin to avoid injury.
Note: Please fully charge the product before using it for the first time, because the main unit is not fully charged when it leaves the factory for safety reasons. While charging, the product cannot be used.
A Dismounting the cleaning head
- Install the cleaning head Align the cleaning head with the Interface on the top of the transducer, use a wrench to align the bayonet and tighten it clockwise;
- Disassemble the cleaning head Replace or remove the cleaning head,Align the bayonet with a wrench and unscrew it counterclockwise to replace or remove.
B Switch mode
Power On
Long press and hold the Power/Mode switch button to start, and the work
indicator will be always on in the Start state.
Mode Switch
After starting, the default mode is soft mode, and short press again to switch
the mode, they are medium mode, strong mode, and then cycle to soft mode. This
instrument has memory mode, the gear you used last time will be the default
mode when you turn on this instrument next time.
Power off
After power on, long press the power/mode switch key to power off or it will
automatically shut down in 15 minutes after you stop using this instrument.
C Clean the teeth
-
When cleaning the calculus, stains and bacteria on the gums, please use the pointed cleaning head to be more slow.
-
When scraping large pieces of calculus and plaque on the neck and sides of the teeth, please use a flat head cleaning head and clean it slowly and several times.
-
Long press the power/mode switch button -to turn on the switch, and then short press the power/mode switch according to the thickness of the calculus key to adjust to the desired mode.
-
When cleaning tooth stains and tartar, please use both sides of the cleaning head to clean to avoid scratching the surface of the teeth; gently touch the cleaning head under the calculus at an angle parallel to the tooth surface or less than 15°, and move it back and forth. , to crush and shake off the calculus.
-
Please use very light force to move the cleaning head back and forth. Do not vibrate the cleaning head at one point, otherwise,lt can cause damage to the tooth surface.
-
Use from the position with less tartar, They can be used in the order shown in the figure above. Use mouth mirrors to assist in unseen positions.
D Product charging
Connect the USB port on the side of the base charger to the power adapter via a USB charging cable, then place the scaler handle into the base to charge.
When charging, the charging indicator is flashing; When fully charged, the charging indicator is always on.
Charging Precautions
- Do not immerse the charging port in water or any liquid;
- Do not charge, use and place the product in a high temperature place;
- It is recommended to use a “CCC” certified 5V DC 1A DC output power adapter. (The power adapter can be used with a mobile phone charging head, or purchased separately)
- This product cannot be used during charging.
Product parameters
Product name: Ultrasonic therapeutic apparatus
Ultrasonic tooth scaler Rated voltage: 5V
Wireless charging current: 1A
Battery capacity: 800mAh
Product size: 208.52828mm
Rated power: 3W
Waterproof rating: IPX6
Product gear: 3-speed
Important Notes
Danger
- Do not use if the power plug or power cord is damaged;
- When turning on the scaler, do not point the metal head at sensitive parts of the human body such as eyes, and dangerous equipment such as power supplies and lamps;
- Do not touch the skin with the metal cleaning head for a long time to avoid injury;
- This product contains a built-in rechargeable battery, please do not heat it in fire or charge, use or place it at high temperature;
- This product is not suitable for people under the age of 18, please keep this product away from children;
- Others who do not have full capacity for civil conduct or lack relevant experience and knowledge must be under the supervision and guidance of the supervisor use, clean and maintain this product.
Warning
- Do not immerse the product in water or any liquid. If it falls into the water when connected to the power supply, please unplug the power plug first and then take out the product;
- Do not press the metal cleaning head hard on the gums or teeth to avoid damage;
- If you need to charge, please confirm that the power plug and the interface are completely dry, and then connect the power;
- Do not modify, disassemble or repair this product by yourself;
- Before connecting the power supply, please check whether the local power supply voltage is consistent with the voltage marked on the product;
- Do not use this product in a bath or bath;
- Do not wrap the power cord around the product when it is powered on;
- Ultrasonic scaling is contraindicated in patients with cardiac pacemakers to avoid symptoms such as dizziness and arrhythmia caused by the interference of electromagnetic radiation;
Note
when using this product for the first time, there may be soreness, itching or
slight bleeding. This is because the gums are not used to this efficient
cleaning method. It is recommended to use the gentle mode of this product to
clean first. This phenomenon will generally stop within 1-2 weeks. If the
above phenomenon improves significantly over 2 weeks, stop using this pad and
consult a dentist in time.
- Users of orthodontics, dental restorations, dental implants, etc., please use them under the guidance of a dentist;
- This product is only designed to be used for household personal cleaning of the mouth, and should not be used for any other purpose, nor for any medical purpose. Use process if you feel any discomfort or pain, please stop.
- If your doctor recommends that you take antibiotics before surgery, you should consult your dentist before using this instrument or any other oral hygiene AIDS;
- Do not knock or drop the product. If the product is damaged due to collision and falling, please stop using it;
- Check for obvious damage before using this product. Do not use if damaged or the machine has been severely dropped;
- If this product (main body, charging port, metal cleaning head) has any signs of damage, please do not use it;
- Do not place the product in a high temperature or humid place, and avoid direct sunlight;
- Before maintenance, ensure that the product is not charged and turned off;
- Do not share the metal cleaning head with others;
- Do not use this product without a cleaning head installed;
- Do not use when wearing oral jewelry, please remove it before use;
- Do not use if you have an open wound on your tongue or mouth.
Removal of fault
| Troubleshooting Symptoms | Trouble causes | Causes Solutions |
|---|
The cleaning head cannot be correctly connected to the power shaft cannot be
turned on.| There is a foreign body blockage at the cleaning head jack, and
the power shaft is stuck with foreign bodies; The cleaning head is not genuine
or not matching; positioning direction is incorrect.| Remove foreign objects;
purchase genuine cleaning heads; follow the prompts for proper positioning
Can not power on.| The battery is exhausted or too low, in charging status|
Charge timely; unplug the charging cable
The cleaning head has a weak vibration| The plug is not properly connected to
the power supply. There is a foreign object between the cleaning head and the
power shaft| Install properly; remove foreign objects
The handle cannot be connected to the charger| There is a foreign object in
the socket at the bottom of the handle| Remove foreign objects
The After charging, it does not display the charging state| The plug is not
properly connected to the power supply| Check if the power supply is connected
No display of charging| The battery is exhausted or too low| Will resume to
normal after charging
Product certification
Product name: Inspection conclusion:
Production date: Inspector:
Warranty Card
Username:
Purchase time:
Contact information:
User address:
Fault: ___
FCC Warning Statement
FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located for operating in conjunction with any other antenna or transmitter.