MASTER AIRBRUSH AB011351J Airbrush Spray Booth Hobby 2 Instruction Manual
- June 12, 2024
- MASTER AIRBRUSH
Table of Contents
MASTER AIRBRUSH AB011351J Airbrush Spray Booth Hobby 2
Product Information
- Product Name: Airbrush Spray Booth Hobby 2
- Model Number: AIRBRUSH-ABSAUGANLAGE HOBBY 2
- Version: 23.06
- Manufacturer: Profi-Pumpe
- Website: http://www.profi-pumpe.de
Product Usage Instructions
Safety Instructions and Warnings
- Please read the user manual before using the pump.
- Pull power plug before performing any maintenance or cleaning.
- Protect the unit from rain and moisture.
- Be cautious of electrical voltage and follow all warning signs.
Introduction
Congratulations on your purchase of the Airbrush Suction Unit. The manufacturer emphasizes functional security and operational safety. To prevent any damage or injury, it is important to read this user manual carefully and follow all safety precautions and instructions for proper use of the airbrush components. Please keep this manual with the instructions and safety instructions for future reference.
Ranges of Application
The Airbrush Spray Booth can be used for the following applications:
- Figurines
- Cups
- Nail design
- Model making
- Handicrafts
- And much more
Important Note
Please pay attention to the following before commissioning the Airbrush Suction Unit:
- Inform yourself about the working methods and techniques through literature or online resources before starting work.
- The unit is strictly for personal use and has been tested by the manufacturer.
- Claims for damages due to improper disassembly and cleaning cannot be accepted.
Startup and Installation
- Open the box.
- Assemble the base plate A and the two side plates B and C.
- Assemble the upper ramp plate D (Five inserts need to be staggered).
- Assemble the top cross plate E.
- Install the fan connector with screws.
- Turn the hose counterclockwise to connect it to the fan connector.
- Connect the exhaust to the hose by turning it counterclockwise.
- Insert the power plug into the socket and switch on the device.
Regular Maintenance
Regularly perform the following checks:
- Ensure that the cable is not damaged.
- Check that the hoses are not bent or broken.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The system does not extract or does not extract properly. | – | – |
| LEDs do not light. | Missing voltage | Ensure the device is switched on. |
| The suction path is blocked or leaking. | – | – |
| Missing voltage | Ensure the device is switched on. | – |
SAFETY INSTRUCTION AND WARNING
- Please read the user manual before using the pump
- Warning sign
- Warning of electrical voltage
- Pull power plug
- Protect from rain and moisture
INTRODUCTION
We would like to congratulate you on the purchase of our Airbrush Suction Unit. We appreciate your trust. That‘s why functional security and operational safety stands on first place for us.
To prevent damage to persons or property, you should read this user manual
carefully. Please observe all safety precautions and instructions for proper
use of the airbrush components. Failure to follow the instructions and safety
precautions can result in injury or property damage.
Please keep this manual with the instructions and safety instructions
carefully in order to at any time you can restore them.
IN GENERAL
The Suction Unit are developed according to the newest stand of technology,
manufactured with much care and go under strict intensive controls.
Make sure after unpacking that the data given on the type label match with the
included operating instructions. In the case of doubt is not to be used.
Transport damages are immediately to be reported to the package distributor on
the shipping invoice and to us in written form.
RANGES OF APPLICATION
Airbrush spray booth can be used in: Figurines, cups, nail design, Model
making, handicrafts and much more.
Important note : Please pay attention before commissioning the Airbrush Suction Unit!
- Please, inform yourself in the literature or on the Internet about the working methods and techniques before starting work.
- We sell only tested products. These are strictly for personal use.
- Claims for damages for improper disassembly and cleaning can not be accepted.
STARTUP AND INSTALLATION
- Open the box.
- Assemble the base plate A and the two side plates B and C.
- Assemble the upper ramp plate D (Five inserts need to be staggered).
- Assemble the top cross plate E.
- Install the fan connector with screws.
- Turn the hose counterclockwise to connect it to the fan connector.
- Now connect the exhaust to the hose by turning it counterclockwise.
- Insert the power plug into the socket, switch on the device.
Note:
- The suction/wind speed can be adjusted from 0 to 5.1m³/MIN.
- Depending on the need, you can turn on the LED light.
- The filter of the spray booth is replaceable and can be easily changed.
The following controls should be carried out regularly:
- That the cable is not damaged
- That the hoses are not bent or broken
Caution: Before each work on the Airbrush Suction Unit the security tips are to be followed.
SECURITY TIPS
- Keep away from children! It is not a toy!
- The unit should not be taken by persons commissioning, which are under the influence of alcohol, drugs or medication.
- Please, check before every use that the electrical connections as well as the cable are intact.
- Moreover, it is not recommended to carry out technical modifications. First it is not sure whether these changes are technically flawless and secondly no guarantee can be therefore granted.
- Obey absolutely valid regulations on the electrical security
- Pay attention to the Ambient temperatures between +5 and +40 ° C
- Never leave the appliance exposed to dust, acids, vapors, explosive or flammable gasses or atmospheric agents (rain, sun, fog, snow)
- The unit may be not be used in areas with steam or moisture, or near water.
- Never use the appliance in your bare feet or with wet hands or feet.
- Never pull on the electrical cable or hose.
- Avoid pinching or kinking hoses or cables.
- The device is to be secured / protected through a RCD circuit breaker (release current 30 mA).
- The unit should not be used if it is damaged.
- Please avoid inhaling the spray mist.
The manufacturer explains:
- To take over no responsibility in the case of accidents or damages on the basis of carelessness or disregard to the instructions in this book.
- To reject every responsibility for the damages which originate from the improper use of the device
TROUBLESHOOTING
| Problem | Possible cause | Solution |
|---|
The system does not extract or does not extract properly.
| Missing voltage| Check the connections and connect the power plug
The device is not switched on| Switch the device ON on the rear panel with the
red
power switch
The suction path is blocked or leaking
| Check that the plastic sleeve is firmly connected to the ventilation grille and that the connections do not have any leaks.
LEDs do not light
| Missing voltage| Check the connections and connect the power plug
The device is not switched on| Switch the device ON on the rear panel with the
red
power switch
GUARANTEE REGULATIONS / STATUTORY WARRANTY
For all manufacturer defects and material defects we grant the legal
guarantee time (new and unused product). In such cases we take over the
exchange or the repair of the device. Forwarding expenses are not carried by
us.
The guarantee is not valid with:
- Material wear (sealing rings, impeller wheels, impeller chambers)
- Unjustified interventions or changes in the device
- Damages by self-fault
- Improper servicing and improper use
Moreover, we give no damage compensation for secondary damages!
NOTES ON DISPOSAL
Electrodevices of our company, labeled with the symbol of the crossed trash
bin, are not permitted to be disposed in your household garbage. We are
registered at the German registration department EAR under the WEEE-No.
DE79535656. This symbol means, that you’re not allowed to treat this product
as a regular household waste item – it has to be disposed at a recycling
collection point of electrical devices. This is the best way to save and
protect our earth.
THANKS FOR YOUR SUPPORT!
EU DECLARATION OF CONFORMITY
The undersigned, Amur S.à r.l., 36, Rue de la Gare, L-5540 Remich, certifies
that the products named overleaf, namely AIRBRUSh-Absauganlage Hobby 2
(AIRBRUSH SPRAY BOOTH Hobby 2) as placed on the market, comply with the
relevant provisions listed below, the relevant EU harmonized directives and
the EU standard for safety. This declaration of conformity applies insofar as
no modifications are made to the product. The sole responsibility for issuing
this declaration of conformity lies with the manufacturer. The sole authorised
person to keep the technical documents: Amur S.à r.l. – 36, Rue de la Gare –
L-5540 Remich Low Voltage Directive (2014/35/EU) EC Electromagnetic
compatibility directive (2014/30/EU)
The following harmonized standards:
- EN 55014-1:2021,
- EN 55014-2-2021,
- EN 61000-3-2:2019/A1:2021,
- EN 61000-3-3:2013/A2:2021,
- EN 60335-1:2012/A15:2021
Signed for and on behalf of Amur S.à r.l. Remich, 20.06.2023 i.V. Dipl. Phys.
Peter Neumüller Technical Manager
TECHNICAL DATA
English| Deutsch| HOBBY 2
(AB011351J)
---|---|---
Input voltage| Eingangsspannung| AC 230V 50HZ
Output voltage| Ausgangsspannung| DC 12V
Fan power| Lüfterleistung| 22.2W
Fan power| Luftstrom| 180 CFM / 0-5,1m³/min
Noise| Lautstärke| 45db
Exhaust air pipe| Abluftrohr| 0.37-1.5m/1.2-5ft
Box size| Box Größe| 44x19x33cm
Weight| Gewicht| 3.15kg
8 LED strips| 8 LED Streifen| 12v, 8mm, 3000k
Imprint
Amur S.à r.l. 36, Rue de la Gare L-5540 Remich Tel: +49 611 9458777-0
SERVICE+RETOURE:www.profi-airbrush.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>