ifi GOPOD Tws Dac Amp Instructions
- June 9, 2024
- ifi
Table of Contents
ifi GOPOD Tws Dac Amp Instructions
OVERVIEW
LED
- Bluetooth
- LED Status
- off Wireless Bluetooth (Connected)
- Blue (flashing) Wireless Bluetooth (Awaiting connection)
- Blue/Red (flashing) Wireless Bluetooth (Pairing)
- Blue/Green flashing) Factory Reset
- Red (long highlight) Charging
Touch control area
- Volume control (turn)
- Play/Pause/Answer the call (a short click)
- Skip forward (two short clicks)
- Skip back (three short clicks)
- Wake up voice assistant (long press 1.5s)
- Pairing (Press the left and right touch area together for 2s)
- Factory Reset (long press 15s)
USB-C (5V) battery charge input
For charging only. Use a 5V/2A and above Qi certied charger or 5V/1A and above Type-C charger.
LED for Battery Status
- LED Status
- 4/4 > 75%
- 3/4 > 50%
- 2/4 > 25%
- 1/4 > 25%
- Battery LED will flash when it is charging and will go out when it is fully charged.
Specifications
- Bluetooth version ： Bluetooth 5.2TM
- Codecs ： AAC, SBC, aptX, aptX HD, aptX Adaptive,
- aptX LL, LDAC, LHDC/HWA Codec)
- Chipset: Qualcomm QCC 5100 Series
- Auto impedance detection : 16Ω/32Ω/64Ω/300Ω
- DNR: > 129dB (A)
- SNR : 32Ω >129dB (A) / 300Ω >132dB (A)
- THD + N : Ω0.002% (1kHz/32Ω)
- Output Noise : <1uV
- Frequency response: 10-43kHz(-3dB) LDAC
- Channel separation: 90dB (1kHz/32Ω)
- Battery: Ear hood 180mAh + Charging box 1500mAh
- Working hours Ear hood ~7h + Charging box ~30h
- Charging time Ear hood ~1.5h + Charging box ~2h
- Power System: 5V/2A and above Qi-certified charger
- 5V/1A and above Type-C charger
Dimensions
- Ear hood 43.5 x 16.4 x 9.5 mm (1.7″ x 0.6″ x 0.4″)
- Charging box 116 x 76 x 38.5 mm (4.6″ x 3″ x 1.5″)
Net weight
- Ear hood 12g (0.42 oz)
- Charging box 126g (4.44 oz)
Limited Warranty
- 12 months*
- 12 months typical or as permitted/required by local reseller laws.
- Specifcations are subject to change without notice.
FCC COMPLIANCE STATEMENT
- This device complies with part 15 of the FCC Rules.
- Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
- The device has been evaluated to meet the general RF exposure requirements.
- The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>