icon Aurora Large Diaphragm Studio Condenser Microphone User Manual
- June 3, 2024
- Icon
Table of Contents
Large-diaphragm Studio Condenser Microphone
User Manual
Aurora Large Diaphragm Studio Condenser Microphone
Out of this world versatility! The Space Series microphones fuse vintage sounding clarity with bold intergalactic design.
|
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
|
---|---|---
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVIDEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle„is
intended tooled the user to the presence of uninsulated dangerous voltage
within the product s enclosure, that may be of sufficient magnitude to
electric shock to persons.
exclamation point within an equilateral triangle is intended to alert the
user of the presence of important operating and maintenance (serviving)
instructions in the literature accompanying the appliance.
Important Safety Instructions
- Read this manual thoroughly before using this unit.
- Keep this manual for future reference.
- Take notice of and comply with all warnings included in the user’s manual or indicated on the appliance.
- Follow all instructions included in this manual.
- Do not expose this unit to rain or moisture. Avoid having water or other liquids spilled on this unit.
- Do not block any ventilation openings or interfere with the proper ventilation of this unit. Install in accordance with the manufacturer’s instructions.
- Do not use or store near any heat sources such as radiators, heat registers, stoves, or other heat− producing appliances.
- To avoid the risk of electrical shock, do not touch any exposed wiring while the unit is in operation.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this unit and all connected electrical equipment during lightning storms or when left unused a long period of time.
- Refer all servicing to qualified service personnel. Servicing is required when the appliance has been damaged in any way or fails to operate normally.
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture
Introduction
Firstly, congratulations on your purchase of the ICON Pro Audio Aurora Studio
condenser microphone! In these pages, you’ll find a detailed description of
the features of the Aurora Studio condenser microphone and a full list of
specifications.
Please register the product on our website at the link below;
www.iconproaudio.com/registration
As with most electronic devices, we strongly recommend you retain the original
packaging. In the unlikely event that the product is returned for servicing,
the original packaging (or reasonable equivalent) is required. With proper
care and adequate air circulation, your Aurora Studio condenser microphone
will operate flawlessly for many years to come.
We trust that this product will provide years of excellent service and in the
unlikely event that your product does not perform to the highest standard,
every effort will be made to address the issue.
What’s in the package?
- Aurora large-diaphragm condenser microphone
- Suspension Shock mount
- Clip on pop shield
- Metal carry case
Register your ICON ProAudio product to your personal account
-
Check serial number of your device
Please go to http://iconproaudio.com/registration or scan the QR code below.
Input your device’s serial number and the other information on the screen. Click “Submit”.
https://iconproaudio.com/registration
A message will pop up showing your device information such as model name and its serial number – Click “Register this device to my account” or if you see any other message, please contact our after-sales service team -
Log in to your personal account page if you are an existing user or sign up as a new user;
Existing user: Please log into your personal user page by inputting your user name and password.
New user: Please click “Sign Up” and fill in all the information. -
Download all useful materials
All your registered devices under your account will show on the page. Each product will be listed along with all its available files such as drivers, firmware, user manuals in different languages and bundled software.
Features
- High degree of clarity for any voice or instrument applications
- Cardioid pickup pattern for outstanding sound source separation and feedback rejection
- Pressure-gradient transducer with shock-mounted capsule
- Perfect for vocals and acoustic instruments
- Professional hand-built 34 mm large-diaphragm capsule for a full, open sound and unsurpassed audio quality
- Heavy-duty suspension mount included
- Ultra-rugged construction with electro-plated finish
- Top-quality components including Wima capacitors and Fairchild resistors
- Suspension shock mount and a clip-on pop filter
- Metal storage carry case
Operating the Aurora
Powering the Aurora (48V)
The Aurora is a condenser microphone and therefore, needs to be operated by
connecting a phantom power supply. Phantom power is standard on most quality
mixers, outboard mic pre-amplifiers and hard disk recorders. If necessary, an
external power supply can also be used. The Aurora receives the phantom power
directly from a microphone cable when connected to a mixer or other microphone
input which includes a phantom supply. The power is actually sent OUT of the
microphone INPUT, riding silently along with the audio signal. Most mixers
have a switch to engage the phantom power so be sure to check that the phantom
power is on.
Setting up the signal level
When connecting the Aurora to a mixer or recorder input, be sure that the
input is at a suitable level. Also, be sure that the 48V phantom power is
engaged as explained above. Most mixers and recorders of reasonable quality
will offer a microphone input with MIC trim (usually called Trim or Gain)
control. The purpose of the MIC trim control is to optimize the amount of good
signal to any noise associated with the mixers electronics. A good MIC pre
with trim also will have a peak or clip LED. To set a good level on the MIC,
set the Aurora up in front of the desired sound source and slowly raise the
MIC trim control until you see the Peak LED light up. Then, turn the mix trim
control down until the LED does not light any more. On most mixers, the ideal
setting is that the trim control is turned up as much as possible without
lighting the Peak LED.
Microphone Placement
In order to maximize the sound quality, you must pay careful attention to the
placement of your Aurora and how it is positioned for the instrument or
vocalist that you are miking. All microphones, especially unidirectional or
cardioids microphones, exhibit a phenomenon know as the “proximity effect”.
Very simply put, proximity effect is a resulting change in the frequency
response of a microphone based on the position of the MIC capsule relative to
the sound source. Specifically, when you point a cardioid MIC directly at the
sound source (on-axis) you will get the best frequency response. However, when
you start pointing the microphone slightly away (off-axis) you will notice the
low frequency dropping off and the microphone will start to sound thinner.
For most vocal applications you’ll want to position the microphone directly in
front of the artist. The same may be true for miking instruments. However, you
can make some pretty amazing equalization adjustments by slightly changing the
angle of the capsule to the sound source. This can be a very useful technique
in capturing the optimum sound of drum set, acoustic guitar, piano or other
instruments in a live room or sound stage. Experimentation and experience are
the best teachers in getting good sounds, so plug in!
P-Popping
P-Popping is that annoying pop sound that you can get when the microphone
diaphragm gets a blast of air from a vocalist pronouncing words with the
letter “P” included, (because it is a “plosive” syllable).
Mounting the Aurora
Mount your Aurora into the suspension mount provided. Squeeze the two side
levers to open the shock mount, insert your Aurora and gently release pressure
on the two levers to secure your Aurora in place. Simply clip the pop guard
into position.
Specifications
Frequency response-vary axis
Acoustical operating principle ………………. Pressure gradient transducer
Type …………………………………………………….. 34 mm Condenser
Polar pattern ………………………………………… Cardioid
Frequency range ………………………………….. 20Hz – 20KHz
Sensitivity ……………………………………………. -35dBV/Pa
Rated Impedance ……………………………….. 200 Ohms
Min. load impedance …………………………. 1000 Ohms
SPL …………………………………………………… 130dB
S/N ratio…………………………………………… 85dB
Dynamic range ………………………………… 125dB
Power supply voltage ………………………. 48V +/-3V
Current consumption …………………….. 4mA
Weight (Microphone only) …………….. 0.189Kg (0.42lb)
(with suspension mount)………………… 0.35Kg (0.78lb)
Dimensions …………………………………… 50mm (dia.) x170m (L)
…………………………………………….. 1.97” (dia.) x 6.69” (L)
Services
If your Aurora needs servicing, follow these instructions.
Check our online Help Center at http://support.iconproaudio.com , for
information, knowledge, and downloads such as:
- FAQ
- Download
- Product Registration
- Video Tutorials
Very often you will find solutions on these pages. If you don’t find a
solution, create a support ticket at our online Help Center at the link below,
and our technical support team will assist you as soon as we can.
Navigate to http://support.iconproaudio.com and then sign in to submit a
ticket.
Once you have submitted an inquiry ticket, our support team will assist you to
resolve the problem with your ICON ProAudio device as soon as possible.
To send defective products for service:
- Ensure the problem is not related to operation error or external system devices.
- Keep this owner’s manual. We don’t need it to repair the unit.
- Pack the unit in its original packaging including end card and box. This is very important. If you have lost the packaging, please make sure you have packed the unit properly. ICON is not responsible for any damage that occurs due to non-factory packing.
- Ship to the ICON tech support center or the local return authorization. See our service centers and distributor service points at the link below:
If you are located in US Send the product to:
North America
Mixware, LLC – U.S. Distributor
3086 W. POST RD.
LAS VEGAS NV 89118
Tel.: (818) 578 4030
Contact: www.mixware.net/help| If you are
located in Hong Kong Send the product to:
ASIA OFFICE:
Unit F, 15/F., Fu Cheung Centre,
No. 5-7 Wong Chuk Yueng Street, Fotan,
Sha Tin, N.T., Hong Kong.
Tel: (852) 2398 2286
Fax: (852) 2789 3947
Email: info.asia@icon-global.com
---|---
If you are located in Europe Send the product to:
Sound Service GmbH
European Headquarter MorizSeeler-Straße3 D-12489 Berlin
Telephone: +49 (0)30 707 130-0
Fax: +49 (0)30 707 130-189
E-Mail: info@sound-service.eu
For additional update information please visit our website at: www.iconproaudio.com
| 
---|---
https://space.bilibili.com/416504902
|
http://weixin.qq.com/r/GDhIUArEmVfmrU4z920K
Twitter
https://twitter.com/iconproaudio
|
Instagram
https://www.instagram.com/iconproaudio
---|---
Facebook
https://www.facebook.com/iconproaudio
|
Youtube
https://www.youtube.com/iconproaudio/channel
Website
http://iconproaudio.com
|
Support
http://support.iconproaudio.com/hc/en-us
|
Dashboardhttp://iconproaudio.com/dashboard/
---|---|---
Documents / Resources
| icon
Aurora Large Diaphragm Studio Condenser
Microphone
[pdf] User Manual
Aurora Large Diaphragm Studio Condenser Microphone, Aurora, Large Diaphragm
Studio Condenser Microphone, Condenser Microphone, Microphone
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>