Fillauer 12P Hosmer Hooks User Manual
- June 3, 2024
- fillauer
Table of Contents
Fillauer 12P Hosmer Hooks User Manual
Intended Use
The Models 10P and 12P are pediatric prosthetic terminal devices commonly referred to as “canted split hooks” and are used to provide for both fine prehension and gross grasping of objects when controlled through a cable that is operated with body motions. They are aluminum and have a plastisol-coated surface to provide protection for the user and other children. These hooks are a voluntary-opening device and grasping tension is adjusted by the adding of tension bands, rings, or springs (see catalog for additional information). See fillauer.com for information on other sizes of canted hooks.
To see other language options, visit fillauer.com.
Scan Me
Performance Characteristics
| Model 12P Model 10P | Model 10P | |
|---|---|---|
| Size | Pediatric | Pediatric |
| Length | 2.75 in. (70 cm) | 3.4 in. (86 cm) |
| Weight | 3 oz. (85 g) | 3 oz. (85 g) |
| Material | Aluminum | Aluminum |
| Grip | Plastisol Coating | Plastisol Coating |
| Attachment | ½-20 Thread | ½-20 Thread |
These devices are intended for single patient use only.
Storage and Handling
It is recommended that prosthetic hooks (or prosthetic/orthotic components) be stored in a cool, clean, dry environment away from harsh chemicals (chlorine, acids, acetone, etc.).
Warnings and Precautions
CAUTION: Aluminum prosthetic hooks are not intended to support partial or full body weight. For heavy duty applications, steel or titanium hooks are recommended.
NOTICE: An upper-limb prosthetic device user’s ability to drive should be determined on a case-by-case basis by a specialist. Contact your local governing authorities regarding any driving restrictions or limitations.
WARNING: Body-powered devices should not rely on cable tension for grasp
control if the user has been cleared to drive with the prosthesis.
Failure to maintain tension while controlling the steering wheel could cause
serious injury or death.
CAUTION: Abnormal or improper environmental conditions will lead to
malfunctioning and damage of the prosthesis and are not covered under the
warranty of the device. This prosthetic component must not be subjected to
dust/debris, liquids other than fresh water, abrasives, vibration, activities
which would damage the biological limb, or prolonged extreme temperatures (<
-5 °C or > 50 °C). Do not allow debris or liquids to remain in the prosthesis
and its components during use. Rinse the device
with fresh water and dry immediately after exposure.
CAUTION: The hook is waterproof to 1 meter. However, if the hook is submerged, it should be rinsed with fresh water and dried immediately to remove salt, chlorine, or debris.
Qualified Provider
Attachment, adjustment, alignment, and delivery of this device must be performed by or under the direct supervision of a qualified prosthetist. Unless stated in this manual, any such activities should not be attempted by the user and will potentially void the device warranty.
Specifications and Preparations Before Use
(Risk Management for Installation and Calibration)
Installation
The hook may be installed in any Filature wrist unit with a ½-20 thread.
Follow the instructions provided with the wrist unit for best results.
Cabling
The hook “thumb” has been designed with a receiver for a ⁹⁄³² inch ball
terminal. A triple swivel with ⁹⁄³² inch ball terminal should be selected with
a cable connection that matches the cable used in the prosthesis. Cable
routing should ensure a direct line of pull that minimizes bends in the cable,
otherwise excess cable friction or failure could result.
Adding Tension to Hook Grasp
To add more force to the grasp of the hook, additional tension bands may be
applied using the E-Z Hook Tension Band Applier (55144) or similar device.
Additional bands are included with the hook and are available in beige (53869)
or black (53869-BLK) for the number 10 Hooks or beige (55674) for the number
12 Hook. For greater tension, hook rings (57500) or stainless-steel tension
springs (55363) may be used. Tension springs are recommended for situations
where chemical or heat exposure could cause
band or ring failure.
Compatibility
Fillauer hooks have been tested with and are recommended for use with Fillauer
wrists that have a ½-20 internal thread. They may be used with any equivalent
½-20 threaded wrist units. However, damage caused by other manufacturers wrist
units is not covered under warranty of this device.
Only Fillauer tension bands, hook rings, and tension springs may be used with
Fillauer hooks to adjust the grasping force of the hook.
Disposal / Waste Handling
The product must be disposed of in accordance with applicable local laws and
regulations. If the product has been exposed to bacteria or other infectious
agents, it must be disposed of in accordance with applicable laws and
regulations for the handling of contaminated material.
All metal components may be removed and recycled at the appropriate recycling
facility.
User Instructions
The providing health care professional must review the following information directly with the user.
Care and Maintenance
CAUTION: Aluminum prosthetic hooks are not intended to support partial or full body weight. For heavy duty applications, steel or titanium hooks are recommended.
NOTICE: An upper-limb prosthetic device user’s ability to drive should be determined on a case-by-case basis by a specialist. Contact your local governing authorities regarding any driving restrictions or limitations.
WARNING: Body-powered devices should not rely on cable tension for grasp
control if the user has been cleared to drive with the prosthesis.
Failure to maintain tension while controlling the steering wheel could cause
serious injury or death.
CAUTION: Abnormal or improper environmental conditions will lead to
malfunctioning and damage of the prosthesis and are not covered under the
warranty of the device. This prosthetic component must not be subjected to
dust/debris, liquids other than fresh water, abrasives, vibration, activities
which would damage the biological limb, or prolonged extreme temperatures (<
-5 °C or > 50 °C). Do not allow debris or liquids to remain in the prosthesis
and its components during use. Rinse the device
with fresh water and dry immediately after exposure.
CAUTION: The hook is waterproof to 1 meter. However, if the hook is submerged, it should be rinsed with fresh water and dried immediately to remove salt, chlorine, or debris.
Serious Incidents
In the unlikely event of a serious incident, seek immediate medical help and contact your prosthetist at your earliest possible convenience. Clinicians should contact their local Fillauer representative immediately in the event of any device failure.
Warranty
This product has an 18-month warranty against manufacturer defects.
Customer Support
Fillauer LLC
2710 Amnicola Highway
Chattanooga, TN 37406
423.624.0946
Fillauer Europe
Kung Hans väg 2
192 68 Sollentuna, Sweden
+46 (0)8 505 332 00
EC REP
© 2021 Fillauer LLC
M087/10-06-21/Rev.1
www.fillauer.com
References
- Home | Fillauer LLC | Orthotics and Prosthetics Manufacturer
- Home | Fillauer LLC | Orthotics and Prosthetics Manufacturer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>