ISEEVY 4K60 2×2 TV Wall Controller User Manual
- June 3, 2024
- ISEEVY
Table of Contents
4K60 2×2 TV Wall Controller
User Manual
Enjoy the vivid world!
Introduction
4K60 2×2 tv wall controller
The 2×2 tv wall controller , support 1-way HDMI input and 4 HDMI output, the
main function is to divide a complete HDMI,HD image signal into 4 blocks and
assign to 4 video display unit (such as Rear projection unit, LCD TV, etc.),
Complete with 4 HDMI high-definition video display units to form a large
dynamic image screen.
Support modes
Features
- *Support 1 HDMI input
- *Support input HDMI 2.0
- *Support 4 HDMI outputs
- *Support input 4K60HZ,and lower resolution
- *Support output resolution 1920x1080P60
- *Support multiple splicing modes, easy to operate, plug and play
Physical interface diagram
OUTPUT → HDMI Signal Output
INPUT → HDMI Signal Input
SPDIF → Digital Audio Output
DC/12V → Power Adptor Input
IR → Remote Receiver
LED → Power Light
RS232 → RS232 Control
Audio → Audio ON or OFF
Mode → Different Mode Switch
→ Flip the picture under the mode of 2×2
Remote controller
Operation steps **
**
STEP 1: Connect hdmi source to hdmi input with HDMI cable,connect hdmi
output to TVs.
STEP 2: Connect 12V power adaptor.
STEP 3: Set up splicing mode by the MODE button on the unit or remote
controller.
The Package includes
- 2X2 tv wall controller x1
- Power adapter x1
- User Manual x1
Connection operation
RS232 remote control
This product supports RS232 remote command control and returns the
status.Connect the RS232 port of the splicer to the PC COM port by a Rs232
uncrossed cable or USB to RS232 adapter. Then install serial port tools in the
PC can use RS232 control.
Parameter configuration of serial port on PC side
| Baud rate | 115200 |
|---|---|
| Parity bits | NONE |
| Data bits | 8 |
| Stop bits | 1 |
Serial port command table:
| NO | Send command | Return |
|---|---|---|
| ASCII | HEX | Instruction |
| 1 | !SwO# | 0x21 0x53 0x57 0x30 0x23 |
| 2 | !Sw1# | 0x21 0x53 0x57 0x31 0x23 |
| 3 | !Sw2# | 0x21 0x53 0x57 0x32 0x23 |
| 4 | !Sw3# | 0x21 0x53 0x57 0x33 0x23 |
| 5 | !Sw4# | 0x21 0x53 0x57 0x34 0x23 |
| 6 | !Sw5# | 0x21 0x53 0x57 0x35 0x23 |
| 7 | !Sw6# | 0x21 0x53 0x57 0x36 0x23 |
| 8 | !Sw7# | 0x21 0x53 0x57 0x37 0x23 |
| 9 | !Sw8# | Ox21 Ox53 Ox57 Ox38 0x23 |
| 10 | !Sw9# | 0x21 0x53 0x57 0x39 0x23 |
NON E
11| !SWA#| 0x21 0x53 0x57 0x41 0x23| Forward loop switch mode| !RCX#(X:0-8)|
NON E
12| !SWB#| 0x21 0x53 0x57 0x42 0x23| Standby| !RcB#| NON E
13| !SWC#| 0x21 0x53 0x57 0x43 0x23| Power on| !RcC#| NON E
14| !SWD#| 0x21 0x53 0x57 0x44 0x23| Turn on the OSD show| !RcD#| NON E
15| !SWE#| 0x21 0x53 0x57 0x45 0x23| Turn off the OSD show| !RcE#| NON E
16| !COM#| 0x21 Ox43 Ox4f Ox4d 0x23| Reads current state| Power state/ OSD
state/ Display mode e.g.!RCC#! RCE#!RC2#| NON E
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>