Greenlight ABY1002W Wall Light Instruction Manual
- June 3, 2024
- Greenlight
Table of Contents
Greenlight ABY1002W Wall Light
Safety Warnings
These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician. This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations and should be installed in accordance with local building regulations. It is for indoor use only, and is not suitable for a bathroom location.
This is a Class l product and must be Earthed. The terminal blocks are supplied according to requirements of the fitting.
IMPORTANT: Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.
The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove existing light fitting. Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting. Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation. Never put anything on the product or hang anything on any part of this product.
IMPORTANT: Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as these may cause over heating and damage the fitting). Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down.
( Caution: bulb gets hot during use). C lea n with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Troubleshooting
When the bulb does not light after installation
- Ensure there is no electricity failure.
- Ensure all the connections are secure.
If you have any doubt about installation/use of this product, consult a qualified electrician.
Assembly Instructions
- First determine the position of the wall bracket. Consider that the wall bracket must cover the wiring and associated hole in the wall.
- Mark with a pencil the position of the top hole. Check for wires in the vicinity, making sure you don’t damage any cables drill a hole and using a suitable wall anchor loosely secure the top of the fitting.
- You can now accurately mark the position of the lower hole with a pencil. Remove the top screw again and carefully drill the lower hole and push in a suitable wall anchor.
- Connect the existing house wiring to the terminal block as shown in Fig. 2.
- Fully tighten all connection ensuring the screws clamp the metal conductors and not the plastic insulation.
- Close the enclosure and check that all the insulation is inside the enclosure box and there are no trapped wires. Ensure the enclosure box is firmly closed.
- Place the insulation box and wiring inside the wall making sure not to damage any cables.
- Attach the fitting to the wall using the supplied screws.
- See Fig. 3. Your wall lamp is supplied with two sets of sleeves, the short sleeve enables the use of the shade ring to accommodate soft shades (sold separately) and the long sleeve is to be used with ‘bare bulbs’. These can easily be swapped by removing the shade ring.
- Unscrewing the candle drip from the fitting and replacing with the alternative candle drip.
- If using a soft shade fit the shorter candle drips. Position the shade on the bulb holder and secure with the plastic shade ring.
- Fit the bulbs. Do not fit a higher wattage or different shaped bulb from that mentioned on the bulb holder, as this could cause over-heating and damage the lamp.
- Finally switch on the fitting to ensure it lights up.
Scan QR code for multi-language
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG Brilliantstrasse 1, D-27442 Gnarrenburg