LaserMax LC9 CENTERFIRE Laser Sight Operator’s Manual
- September 19, 2024
- LaserMax
Table of Contents
LaserMax LC9 CENTERFIRE Laser Sight
PARTS IDENTIFICATION
Right Housing
Left Housing
IMPORTANT: Before installation, battery change, cleaning, or maintenance, follow the firearm operator’s manual to ensure that the firearm is unloaded.
INSTALLATION
This state-of-the-art laser sighting system is designed
for use with a specific pistol platform. Do not attempt installation on any
other firearm model/s.
-
Place the right housing onto the trigger guard of the pistol as shown, ensuring that the rear portion of the right housing is securely positioned (figure 1) and the trigger guard is aligned with the channel in the light housing (figure 2).
-
Press the right housing firmly in place by applying upward pressure to the ear portion until the housing snaps into place.
-
Insert rear portion of left housing into the right housing at a 45 degree angle (figure 3).
-
Mate left housing with right housing, ensuring that activation switch passes through opening in left housing. Press together to remove gap.
Important: CenterFire® mounting screws are selftapping; extra care should be taken when installing them for the first time to ensure that they are screwed in straight. Improper installation could cause the threads to strip. -
Install two (2) mounting screws into left housing with a Phillips screwdriver (not provided), starting with screw closest to barrel (figure 4). Next, tighten each mounting screw until secure. Do not over-tighten; this may damage the CenterFire® housing.
OPERATION
- To turn the laser on, press in on the activation switchfrom either side (figure 5). Press again to turn the laser off.
- To switch aiming point from pulse to steady, press and release the activation switch from either side to activate the laser. Then, press and hold the activation switch for 5 seconds. The laser mode will change. Repeat the process to return to the previous mode.
- To save power and prevent inadvertent battery drain, the CenterFire® will shut off automatically after a ten minute period of inactivity. Cycle the activation switch to turn laser back on.
ALIGNING THE LASER
-
Verify proper alignment by comparing laser aiming point to iron sights at a distance of 10 yards for initial alignment. The laser dot should be slightly above the iron sights.
-
To make adjustments, insert adjustment tool into one of the two alignment ports (figures 6 & 7) and slowly rotate the tool while comparing laser position on target to fixed sights.
Important: Do not rotate adjustment tool more than one full turn in either direction from the factory position. This may cause damage to the laser and void the warranty. A one quarter turn will result in a movement of approximately 3 inches at 10 yards. -
Windage adjustment: with the muzzle pointing forward and adjustment tool inserted into the windage port, a clockwise turn will shift the laser aiming point to the left and a counterclockwise turn will shift the laser beam to the right (figure 6).
-
Elevation adjustment: with the muzzle pointing forward and adjustment tool inserted into the elevation port, a clockwise turn will shift the laser beam up and a counterclockwise turn will shift the laser beam down (figure 7).
-
Verify zero by shooting target and making additional adjustments as needed.
Note: a slight shift in alignment may be observed after firing the first time. Recheck alignment after break in and readjust as necessary.
BATTERY REPLACEMENT
TIP: During periods of non-use, test the LaserMax laser periodically to ensure adequate battery levels.
- Remove mounting screws to separate left housing from CenterFire® assembly.
- Lift expended 1/3N Lithium battery out of right housing.
- Install a fresh 1/3N Lithium battery with the positive (+)\ facing coiled spring. (figure 8).
- Reinstall left housing as previously described in INSTALLATION section, Step 4.
CLEANING & MAINTENANCE
After repeated fire, the lens may become clouded with gunpowder residue. For best results, it is recommended that this area be cleaned, along with the firearm, after each use. To clean the lens, follow these steps.
- Keep firearm pointed in a safe direction.
- Confirm laser is off.
- Dampen the end of a cotton swab with isopropyl alcohol.
- Apply dampened swab to lens and polish in a small circular pattern. Be sure to clean around edges of lens.
Firearm should be cleaned and lubricated exactly as directed in the Owner’s Manual. Excess lubricant can interfere with the proper function of both the firearm and the CenterFire® laser. LaserMax components should never be submerged or flushed with cleaning solvents. Failure to adhere to these guidelines may cause damage and void the factory warranty.
FAQs
What is the LaserMax LC9 CENTERFIRE Laser Sight designed for?
The LaserMax LC9 CENTERFIRE Laser Sight is specifically designed for the Ruger LC9 pistol, enhancing accuracy and target acquisition.
How do you install the LaserMax LC9 CENTERFIRE Laser Sight?
The LaserMax LC9 CENTERFIRE Laser Sight can be easily mounted without gunsmithing, ensuring a straightforward installation process.
What color laser does the LaserMax LC9 CENTERFIRE Laser Sight feature?
The LaserMax LC9 CENTERFIRE Laser Sight features a bright red laser for high visibility during use.
How does the LaserMax LC9 CENTERFIRE Laser Sight activate?
The LaserMax LC9 CENTERFIRE Laser Sight activates automatically when the trigger of the Ruger LC9 is pulled, providing instant readiness.
How does the design of the LaserMax LC9 CENTERFIRE Laser Sight aid in handling?
The LaserMax LC9 CENTERFIRE Laser Sight has a compact and rounded design that blends seamlessly with the firearm, promoting smooth drawing and aiming.
What is the automatic time-out feature of the LaserMax LC9 CENTERFIRE Laser Sight?
The LaserMax LC9 CENTERFIRE Laser Sight includes a 10-minute automatic time- out feature to prevent unnecessary battery drain.
What is the weight of the LaserMax LC9 CENTERFIRE Laser Sight?
The LaserMax LC9 CENTERFIRE Laser Sight weighs approximately 0.5 ounces, making it lightweight and easy to handle.
Is the LaserMax LC9 CENTERFIRE Laser Sight compatible with other firearm models?
While primarily designed for the Ruger LC9, the LaserMax LC9 CENTERFIRE Laser Sight is also compatible with other popular firearm models listed by LaserMax.
What technology does the LaserMax LC9 CENTERFIRE Laser Sight utilize for activation?
The LaserMax LC9 CENTERFIRE Laser Sight utilizes GripSense technology, which senses the user’s hand placement for automatic activation.
What type of laser does the LaserMax LC9 CENTERFIRE use?
The LaserMax LC9 CENTERFIRE uses a red laser.
What type of batteries does the LaserMax LC9 CENTERFIRE use?
The LaserMax LC9 CENTERFIRE uses a 1/3N lithium battery.
How is the windage and elevation adjusted on the LaserMax LC9 CENTERFIRE?
The windage and elevation on the LaserMax LC9 CENTERFIRE are user-adjustable.
Download this Manual:LaserMax LC9 CENTERFIRE Laser Sight Operator’s Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>