Hawk eye FPV 4K Thumb Cam 2 Gyroflow Smooth Installation Guide
- September 18, 2024
- Hawk eye
Table of Contents
- FPV 4K Thumb Cam 2 Gyroflow Smooth
- Specifications:
- Product Usage Instructions:
- Installation:
- Record Videos:
- File Transfer:
- PC CAM Mode:
- How to Use Gyroflow (IOS):
- Q: Where can I find the latest manual?
- Q: What should I do if the camera does not turn on?
- Q: How do I connect the camera to my smartphone?
- Q: Can I use ND filters with this camera?
FPV 4K Thumb Cam 2 Gyroflow Smooth
“`html
Specifications:
-
Resolutions:
- 4K 50FPS (4:3, 2880*2160 No gyro data)
- 4K 30FPS
- 1080P 50FPS
- 2.5K 50/30FPS
- 2.5K 50/30FPS 4:3
-
AV output: Micro SD card supported
-
Size: PAL/NTSC (PAL has lower latency) U1 SanDisk
recommend -
Supported SD Card: 8-256GB (FAT32/exFAT)
-
Weight: 34g
-
File Format: *.MP4/H.265
-
Lens Angle: F/2.0 7 glasses Diagonal 170 degrees
-
Voltage: USB 5V, 4PIN PORT 6-23V
-
Current: 500mA
-
Battery: 620mAh Wi-Fi OFF, 1080P for about 1.7 hours (100
minutes)
Product Usage Instructions:
Installation:
Soft mount is needed between the camera and the drone frame. Use
TPU Mount or 3M double-sided tape.
Record Videos:
- Insert an SD card.
- Press the Power/OK button once to start recording.
- Use a U3 speed SD card.
- Format the SD card to FAT32 or exFAT for the first time.
When Quick record mode or Auto record mode is ON, the camera
will automatically record video after power on without needing to
press the record button.
File Transfer:
When the camera is turned ON, connect it to the computer with a
USB cable, and the camera will automatically enter Mass Storage
Mode.
PC CAM Mode:
When the camera is turned OFF, connect it to the computer with a
USB cable, and the camera will automatically enter PC CAM mode. Use
amcap software to view the PC cam.
How to Use Gyroflow (IOS):
-
Search “gyroflow” on the app store.
-
Use an SD card reader to access the video and gyro data on the
SD card, ensuring they are in the same directory. -
Note: 4K 50FPS cannot be stabilized due to the lack of gyro
data in this resolution. -
Select a video file in the SD card directory.
FAQ:
Q: Where can I find the latest manual?
A: The latest manual can be found at this link:
Latest
Manual
Q: What should I do if the camera does not turn on?
A: Ensure that the built-in battery is charged by connecting it
to a power source using the provided USB cable.
Q: How do I connect the camera to my smartphone?
A: Double click on the camera’s Wi-Fi button to activate Wi-Fi
mode, then search for “Hawkeye-xxxx” on your smartphone’s Wi-Fi
settings and connect using the default password: 12345678.
Q: Can I use ND filters with this camera?
A: ND filters are optional accessories that can be used with
this camera for specific shooting conditions.
“`
www.CNfpv.com
Hawkeye 4K Thumb Cam 2 Gyroflow Smooth
Gyroflow Video Smooth Built in battery Wi-Fi
AV output/Video trigger V3.0
Newst Manual:
https://drive.google.com/file/d/1DTtlx1eGgTv_7EghYOsfUN_17E_0MGby/view?usp=sharing
Contents
www.CNfpv.com
Safety Guidelines……………………………………………………………………………………………3 Features
………………………………………………………………………………………………………..4
Button:……………………………………………………………………………………………………………..4 LED indicator
………………………………………………………………………………………………..4 Wifi LED indicator:
……………………………………………………………………………………………4 APP control the camera:
……………………………………………………………………………………..4 4 PIN ports(1.25MM):
………………………………………………………………………………………..6 Type C Port:
……………………………………………………………………………………………………..6 Format SD
Card:………………………………………………………………………………………………..8 Installation:
……………………………………………………………………………………………………….8 Record
videos:…………………………………………………………………………………………………..8 File Transfer:
…………………………………………………………………………………………………….8 PC
CAM:………………………………………………………………………………………………………….9 How to use Gyroflow
:………………………………………………………………………………………..9
IOS ………………………………………………………………………………………………………..9 Android:
…………………………………………………………………………………………………..11 PC( WIN 10, 11):
……………………………………………………………………………………….15 Portrait video
……………………………………………………………………………………………….17 Notes for Gyroflow
:…………………………………………………………………………………………19 Update Firmware:
…………………………………………………………………………………………….21 Video Settings:
………………………………………………………………………………………………..21 System Settings:
………………………………………………………………………………………………22 Camera set up & tutorials:
…………………………………………………………………………………24 Gyroflow software
tutorial:………………………………………………………………………………..24 Triggers:
…………………………………………………………………………………………………………24 Remote control to record
video:………………………………………………………………………….25 Remote control to record video :
…………………………………………………………………………26
Safety Guidelines
www.CNfpv.com
Please read the instruction manual carefully before using the camera for the first time. Please check the latest version manual on our website.
1.It’s a high-precision product, do not drop or crash it. 2.Do not expose the camera to strong magnetic objects, such as magnets or electrical motors. Avoid exposing the product to strong radio waves. Strong magnetic fields may cause the products breakdown or image/audio damage. 3.Never leave the products exposed to high temperatures and direct sunlight. 4.In case of overheating, smoke, or unpleasant smell, unplug your device immediately to prevent fire hazard. 5.Keep the product out of children’s reach. Power cable may cause children accidental suffocation or electric shock. 6.Keep the device in cool, dry and dust-free places. 7.Please do not throw the product or it’s battery to the garbage, find a specific recycling place for it.
Features
www.CNfpv.com
Note: ND filters are optional.
Button:
Name Power/Record/
WiFi Button
Long press Power ON
Click
Start/Stop Recording Power ON(WHEN Quick
recording mode ON)
LED indicator
Charging LED 2.5K 43 50FPS
2.5K 50FPS 1080P 50FPS
4K 30
ON: charging; OFF: finish
Red + Green, Flashing when recording
Red Flashing when recording
Green Flashing when recording
Green Flashing when recording
Wifi LED indicator:
ALL LED alternately flashing
APP control the camera:
Sear “OKJ” on the ios.
Double Click Turn ON/OFF WiFi
Google Play:
www.CNfpv.com
Double click to turn on the camera Wi-FiWhen the camera is ON,LED are flashing
alternative.
Double Click Search “Hawkeye-xxxx”in Wi-Fi with the smart phone and connect
it. Default password: 12345678
After connecting the camera, run OKJ APP and then connect the camera.
4 PIN ports(1.25MM):
www.CNfpv.com
Video trigger: Active low. Please follow remote control. Remote control to
record video 1: AV Out: Analog video output GND: Ground Power: +6-23V
Note: Never connect video/trigger port to power+!!!
Type C Port:
A8,B8 : TV output (16pin or 24pin), need to set TV OUT ON to enable TV output
on APP.
www.CNfpv.com
Performance and Specifications:
Resolutions
www.CNfpv.com
4K 50FPS(4:3 ,2880*2160 No gyro data) 4K 30FPS/
1080P 50FPS/ 2.5K 50/30FPS/ 2.5K 50/30FPS 4:3
AV output
Micro SD card SD card supported
Size
PAL/NTSC PAL has lower latency! U1 SanDisk recommend
8-256G(FAT32/exFAT)
52.5×23*21.7 MM
Weight
34g
File format Lens Angle
Voltage Current Battery
*.MP4/H.265 F/2.0 7 glasses Diagonal 170 degrees USB 5V, 4PIN PORT6-23V
500mA 620maH Wi-Fi OFF, 1080P for about 1.7 hours(100minutes)
Format SD Card: You need to format SD card to FAT32/exFAT for the first time
Installation:
Soft mount is needed between the camera and the drone frame. Use TPU Mount or
3M double-sided tape.
Record videos:
Please insert SD card, then press Power/OK button once to record. Please use
U3 speed SD card. Format the SD card to FAT32 or exFAT at the first time.
When Quick record mode or Auto record mode is ON, the camera will auto record
video after power on, no need to press record button.
File Transfer: When the camera is turned ON, connect it to the computer with a
USB cable and the camera will automatically enter Mass Storage Mode.
PC CAM:
www.CNfpv.com
When the camera is turned OFF, connect it to the computer with a
USB cable and the camera will automatically enter PC CAM mode.
Use “amcap” software to see the pc cam.
How to use Gyroflow : IOS
IOS:Please search “gyroflow: on app store. 1. Use sd card reader to ready the
video and gyro data on the sd card, make
sure they are on the same directory. 4K 50 can not be stabled, cause no gyro
data in this resolution
2. Select a video file in the sd card directory.
3. Click on the blue font (Normally for the first time to authorize)to select the file directory for access authorization.
www.CNfpv.com
4. Click auto sync to sync the video and gyro data(Keep gyro offset and
search size defaultsync points at least 5 ).
5. Export video
6. You can select a video clip or change resolutions to reduce the rending
time.
www.CNfpv.com
Video tutorial https://youtu.be/NaIAbzdivl0?si=Ji2aoBxGAELgyFMN
Android:
Android: Please MUST USE this version gyroflow, or you will waste your time,
and the tutorial is not match. https://drive.google.com/file/d/1gHmF8C-
gqs___9XqPbChQVJ-LdMjNdhN/view?usp= sharing
Use sd card reader to ready the video and gyro data on the sd card, make sure
they are on the same directory. 4K 50 can not be stabled, cause no
gyro data in this resolution 1. Select a video file in the sd card directory.
www.CNfpv.com
2. Click on the blue font(Normally ONLY for the first time to authorize) to select the file directory for access authorization.
www.CNfpv.com
3. Click “auto sync”(Keep gyro offset ,search size default, sync points at
least 5 ) .
4. When finished, Export video
5. You can select a video clip or change resolutions to reduce the rending
time.
www.CNfpv.com
Video tutorial https://youtu.be/F7fNt5FCvkQ?si=YDwFWvUEyHh5NCuf
PC( WIN 10, 11):
www.CNfpv.com
Software downloads (Please MUST USE this version gyroflow, or you
will waste your time, and the tutorial is not match):
https://drive.google.com/file/d/1b9hHcAquPv38hZttc9Xcz6gURHscVj-k/vi ew
The video and the gyro files are NEED to placed in the same directly and the
file names are the same. 4K 50
cannot be stabled, cause no gyro data in this resolution
2. Double click to run gyroflow.exe and drop the video file in to the software.
2. Sync search size keep default, then Click “Auto sync” and wait.
www.CNfpv.com
3. When the sync process is finished, export video. 4. For saving time ,you
can select a video click to output.
Portrait video
www.CNfpv.com
When camera play in portrait, input 90 degrees in “rotation” in gyroflow:
Set the output to portrait mode.
How to flip the chest clip to a vertical screen.
www.CNfpv.com
Notes for Gyroflow :
1. Sync time change to 3-5 second:
www.CNfpv.com
2.Use rs-sync: 3.4K 50 can not be stabled, cause no gyro data in this
resolution 4.Select Dynamic zooming, then there will be no black side.
5.Sync points should be similar number, if its too different, delete it and
add a sync point on other point(right click on the mouse).
6.If can’t export video , turn GPU off, change to H.264.
www.CNfpv.com
7.Software require Win 10,11. If can’t open the software, install the VC pack:
VC_redist.x64.exe . Download link :
https://aka.ms/vs/17/release/vc_redist.x64.exe 8. If still can’t open, you can
install VC: 9. https://visualstudio.microsoft.com/zh-hans/downloads/?cid
=learn-onpage-
download-cta
10. The light dot is optical flow, you could turn it off.
Update Firmware:
1. Delete all the files and folders in the SD card. 2. Download the bin
firmware to SD card. 3. Insert the SD card into the camera. 4. Power on the
camera and it will update firmware automatically. 5. When updating, the LED
will flash. 6. When the update process is finished, the LED will stop
flashing. 7. The camera will reboot again. 8. Please check on www.CNfpv.com
for new firmware updates.
Scan to watch how to update firmware:
https://youtu.be/36fSIRs1pzE?si=vT9vUGLPa9ztV3Sk
www.CNfpv.com
Video Settings:
Resolution4K 50/30fps2.5K 50fps, 2.5K 50/30(4:3)fps, 1080p 50fps, 1080p 30fps.
Note: High frame rates make the TV output smoother! We advice to use 50fps for
FPV! Note: 4K 50FPS can’t log the gyro data!
Loop recording13 510minutes. When the SD card is full, video will be auto loop
recording. When the SD card is full, video will be auto loop recording. The
oldest file will be deleted first. WDROffOn. WDR effect will be On/Off. Note:
When this function is turned on, the image will not become dark even toward
the sun. The image would not look so clear if this function is ON sometimes.
As a FPV cam, this function should be turned ON. Exposure
+2.0+5/3+4/3+1.0+2/3+1/30-1/3-2/3-1.0-4/3-5/3
www.CNfpv.com
-2.0.Note:Higher value for brighter image. If you want brighter image, set this value higher. If the image is over exposure, set the value smaller.
Record AudioOffOn. Time-lapse recordOff0.050.10.5135103060sec.Note: Time-lapse
is a video recording mode that captures video at a very low frame rate: around
one to two frames per second, although this depends on the length of the
recording. When played back, time-lapse video is almost the opposite of slow
motion. Higher value for shorter video. There’s no voice in this mode.
Metering: AverageCenter-weightedSpot, Upper meter, Lower meter.
SharpnessStrongNormalSoft. ContrastHighMediumLow. Auto RecordingOffOn. Note:
The camera will turn on and record automatically without pressing button. When
you stop recording, you need to press the record button. When the power is
suddenly cut off or the stop recording button is not pressed, the file will be
damaged. You need to use the keyboard to enter the playback mode. When you
play back the damaged file, the file will be repaired automatically. QUICK
recording modeOFF, ON: When it’s ON. Short press to turn on the camera (long
press to turn on by default), and then it will automatically start recording;
press again to stop recording, and then within 5 seconds, if there is no
operation, the camera will automatically shut down. Electronic shutterFix the
shutter speed. Auto, 1/60, 1/120,1/240,1/480,1/960,1/1200,1/1440, 1/1920,
1/3840,1/7680. Gyro logOff, on. Save the gyro log and stable the image in PC.
Gyro calibrationPlease place the camera horizontally and keep it sate still,
press OK button to start.
System Settings:
Date time setting. Set daytime.
Auto power offOff123510minutes.The camera will turn off when there’s no
operation. Beep soundOffOnSet the beep sound on/off. LanguageEnglish,.
Frequency5060HZ. Light frequency indoor. When the video flickers indoor,
change this setting. TV modeNTSCPAL. We suggest NTSC that more smooth. TV
ratio16943 43 Full. Adjust the TV output scale. ISO:Auto10020040080016003200.
The term was carried over from film, when
www.CNfpv.com
the ISO rating was known as the “film speed” and “ASA.” Having a standard of
sensitivity is important, as it allows you to shoot the same ISO on different
cameras and trust that the exposure value will be equal. Lower ISO, darker
image, less noise. ColorColorBlack&whiteSepia, Flat color. White
balanceAuto6500K,6000K,5500K, 5000K,4150K,4000K, 3000K,2850K,2700K. White
balance affects the image, warmer or cooler. Different Lens should use
different white balance too. We recommend Hawkeye 4 for the stander lens.
White balance auto lockOff, On. When start recording, the current white
balance will be locked. De-noiseOFF, ON Image rotationOff,OnTurn the image
upside down. OSD ModeOffOn. OSD on TV output.OSD on TV output. To disable the
OSD, turn this Off. USBMass storage, PC Cam. FormatFormat the SD card. Note:
format the SD card at the first time,or the camera can’t recognize the SD
card.
Default settings. if you have any question, you can set to default settings.
Version. Version number. Check its the newest firmware on www.CNfpv.com.
Camera set up & tutorials:
Gyroflow software tutorial:
www.CNfpv.com
Triggers:
The trigger pins(Active Low) need to be connected to the trigger control
cable. Scan to watch.
Note: Don’t connect the trigger pins to any power. If you want to control it
by a MCU, connect it to a 3.3V GPIO through a 1K resistance.
Remote control to record video:
A 2 way switch to control .
www.CNfpv.com
The following example uses Betaflight F405 flight controller to illustrate how to configure the remote control to turn on/off the video recording function. Use the TX1 pin on the flight controller to control the recording and connect the Hawkeye Cam’s TRG PIN(video trigger PIN). If you use other flight controllers, there may be available TX pads instead of TX1, and they may use different resource allocations. You need to adjust the configuration accordingly for your specific flight controller.
Configure the PINIO function of the TX1 pin through the following Betaflight
commands.
resource SERIAL_TX 1 NONE // Close the serial port function of TX1 spindle
resource PINIO 2 A09 // Configure TX1 pin (A09 pin) as PINIO function No. 2
set pinio_box = 40,41,255,255 // Set the PINIO function interval Save // Save
configuration
(If you need to change to other pins, you only need to change the pin number
of the first and second lines of instructions, and the instructions of the
third and fourth lines remain unchanged.)
The following figure configures the PINIO function mapping relationship
between the remote controller and the flight controller. In Betaflight
configuration, PINIO No. 2 function (ie USER2 in the figure below) corresponds
to the AUX5 channel of the remote control.
To activate or deactivate functions on the camera, you need to move the switch from the inactive state (white area) to the active state (yellow area), and then back to the inactive state (white area). To The switch configuration of the flight controller and radio controller must match the settings of your own device. Before configuring, make sure you know what you are doing. If you are not using the remote control function, please cut off or insulate the yellow and green wires separately, and do not connect them to any location.
Remote control to record video :
NOTE: FC Arm to record, dis-arm to stop recording.
www.CNfpv.com
The following example uses Betaflight F405 flight controller to illustrate how
to configure the remote control to turn on/off the video recording function.
Use the TX2 pin on the flight controller to control the recording and connect
the Hawkeye Cam’s TRG wire (video trigger). If you use other flight
controllers, there may be available TX pads instead of TX2, and they may use
different resource allocations. You need to adjust the configuration
accordingly for your specific flight controller.
Configure the PINIO function of the TX2 pin through the following Betaflight
commands.
resource SERIAL_TX 2 NONE // Close the serial port function of TX1 spindle
resource PINIO 2 A02 // Configure TX2 pin (A02 pin) as PINIO function No. 2
set pinio_config = 1,129,1,1 // set PINO 2 Reverse output(129), 1 for Forward
output
set pinio_box = 40,0,255,255 // Set the PINIO2 as ARM state output Save //
MUST Save configuration
(If you need to change to other pins, you only need to change the pin number
of the first and second lines of instructions, and the instructions of the
third and fourth lines remain unchanged.)
After the settings, the camera will auto record when the drone is armed, and
stop recording when it’s dis-armed.
The switch configuration of the flight controller and radio controller must
match the settings of your own device. Before configuring, make sure you know
what you are doing. If you are not using the remote control function, please
do not connect the wires to any location.
Mark: USE resource command to check the pin map
3D print files download from:
https://www.thingiverse.com/hawkeyefpv2/designs
www.CNfpv.com
NOTE:
Check on www.CNfpv.com for new firmware/Manual updates.
For more information please check our Youtube/Facebook/Instagram/Ticktock
channel:
HawkeyeFPV
www.CNfpv.com
FCC STATEMENT This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: — Reorient or relocate
the receiving antenna. — Increase the separation between the equipment and
receiver. — Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. — Consult the dealer or an
experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
2
References
- Hawkeye FPV Monitors and Cameras 鹰眼弘创_Hawkeye FPV Monitors and Cameras 鹰眼弘创
- aka.ms/vs/17/release/vc_redist.x64.exe
- 下载 Visual Studio Tools - 免费安装 Windows、Mac、Linux
- About HawkeyeFPV2 - Thingiverse
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>