Youmin PTC-SH019 Ceramic Heater Instruction Manual
- September 6, 2024
- Youmin
Table of Contents
PTC-SH019 Ceramic Heater
“`html
Specifications
- Product: Ceramic Heater
- Model: PTC-SH019
- Power: 1500 watts
- Dimensions: D=350mm
- Features: Timer, Remote Control, WiFi connectivity
Product Usage Instructions
Important Safety Instructions
Before using the ceramic heater, please read and follow these
important safety guidelines:
-
Do not touch hot surfaces to avoid burns.
-
Avoid placing combustible materials near the heater.
-
Always plug the heater directly into a wall outlet.
-
Do not tamper with the product or attempt to fix it.
-
Keep the heater away from children or individuals with reduced
capabilities. -
If you have aluminum wiring in your home, consult a licensed
electrician before use.
Installation
Follow these steps to install the ceramic heater:
-
Use the provided TEMPLATE to mark the installation area with
dimensions D=350mm. -
Insert the expansible tubes into the holes and tighten them
with screws (ensure a bare part length of 10mm). -
Mount the fan heater on the wall ensuring proper alignment of
holes and stability.
Control Panel and Display
The control panel includes options for timer settings, mode
selection, temperature control, and WiFi reset. Use the remote
control for convenience.
Operations
To operate the ceramic heater:
-
Press the ON-OFF switch to power the unit ON or OFF.
-
Press multiple times to switch between high power mode, low
power mode, fan-only mode, and standby mode. -
Set the timer by pressing the button to add hours (0-24
hours). -
To reset WiFi, press and hold the button for 3 seconds.
Frequently Asked Questions (FAQ)
Q: Can I use an extension cord with this heater?
A: No, always plug the heater directly into a wall outlet for
safety.
Q: How do I clean or store the heater?
A: Before cleaning or storing, ensure the controls are set to
OFF, disconnect from the power outlet, and allow it to cool.
“`
CERAMIC HEATER
INSTRUCTION MANUAL
MODEL:PTC-SH019
Content
IMPORTANT INSTRUCTIONS ………………………………………… 1 INSTALLATION
……………………………………………………………… 3 OPERATIONS………………………………………………………………….. 5 OVERHEAT
PROTECTON ………………………………………………. 7 MAINTENANCE AND CLEANING………………………………….. 7
SPECIFICATIONS……………………………………………………………. 7 APP DOWNLOAD…………………………………………………………….
8 AFTER-SALE SERVICE…………………………………………………… 9
IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS
To ensure the best performance from your heater, please read and save the
following instructions
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS INCLUDING THE
FOLLOWING:
Read all instructions before using this heater. This heater is hot when in
use. To avoid burns, do not let bare skin touch hot
surfaces. Keep combustible materials such as drapes, furniture, pillows,
bedding, papers,
clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and
keep them at least 1 foot ( 0.3m) the sides and rear of the heater. Extreme
caution is necessary when any heater is used by or near children or
invalids,and whenever the heater is left operating and unattended. Always
unplug heater when not in use. Do not operate any heater with a damaged cord
or plug, or after the heater malfunctions or has been dropped or damaged in
any manner. Discard t h e heater or return the heater to authorized service
facility for examination and/or repair. Do not use in outdoors. Never locate
heater where it may fall into a bathtub or other water container. Do not run
cord under carpeting. Do not cover cord with rugs, runners, or similar
coverings. Arrange cord away from traffic area and where it will not be
tripped over. To disconnect the heater, to control to OFF then remove plug
from outlet. Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock or fire or damage the
heater. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like a bed, where openings may become
blocked. A heater has hot and arcing or sparking parts inside. Do not use it
in areas where gasoline, paint or flammable liquids are used or stored. Use
this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock or injury to persons.
Always plug heater directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
1
Never tamper with this product or attempt to fix it. Any tampering with, or
modification of this heater can result in serious injury, death, or fire. Risk
of electric shock. Do not open. No user serviceable parts inside.
This heater is not intended for use by persons (including children)with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
If your home has aluminum wiring, you will need a licensed electrician to
check your receptacle’s connections.When using a 1500-watt heater, aluminum
wire connections may cause a safety issue.
Before cleaning or storage, turn the product’s controls to the OFF position
and disconnect the heater from the electrical outlet and allow it to cool.
2
INSTALLATION
The heater must be installed on a wall before operating. Don’t try to use it
without installation. The installation sequence of the fan heater is as
follows: 1. Find a space to install the fan heater. 2. Drill two holes of the
dimension of the expansible tubes ¢ – 8 mm – in the wall
(See Figure ) – D= 350mm by using the TEMPLATE. 3. Insert the expansible tubes
into the holes and tighten them with the screws provided
firmly. NOTE: Fasten the screws tightly. Do not fasten the screw into the
expansible tube thoroughly; the length of the bare parts should be 10 mm. 4.
Mount the fan heater to the wall . Make sure the two holes located on the back
of
the heater do aim at the above two screws, then push the heater backwards to
the wall, and then downwards till the unit is stable.
Hanging Hole Dimension : 350mm
Window outlet
Main OF/OFF Switch
Window inlet
3
The Control Panel and Display
Timer/ WIFI Reset
Mode
Remote Control
Timer Temperature
Control
WIFI Reset
ON/OFF Mode
4
OPERATIONS
Control Panel Operation
Press the ON-OFF switch at the right side of the unit to switch the appliance
ON (I) or OFF (O)
Press at the first time to enter the high power mode
– Press again to the low power mode
– P ress at the third time to the fan only.
– Press at the fourth time, the heater enters into the standby mode ( the fan
will run for 30 seconds and then turn off )
-Long press for 3 seconds to turn off the effect lighting.
Press the button to set the timer (From0 hour – 24hours). Each time you
press the button adds an hour to the timer. The display will show current
setting time for 3 seconds after setting, and then the setting time and
setting
temperature will be cycle showed. At the same time,
light turns on.
Press the on the control panel for 3 seconds is to reset the WIFI. The unit
will be disconnected from your device.
Remote Control Operation
Press to turn on or off the heater Press to select the mode of high power low
power and fan only. Long press for 3 seconds to turn off the effect lighting.
Press to set the timer (From0 hour – 24hours). One press of the button
adds an hour to the timer. The display will show current setting time for 3
seconds after setting, and then the setting time and setting temperature will
5
be cycle showed. At the same time,
light turns on.
Press / to adjust thermostat control. Temperature setting from
50-95 degree. The button of is to increase the desired temperature and
is to decrease it.
Press
for 3 seconds to reset the WIFI.The unit will be disconnected
from your device.
Battery
The remote control requires 1 CR2025 3V lithium battery (not included)
Important: Follow the instructions of use and the recycle rules given on the
battery packaging. 1- Open the battery compartment by sliding the cover down.
2- Insert the battery into the compartment, observing the polarity in the
diagram (see below drawing). 3- Close the battery compartment.
Smart Heater Operation with WIFI USE YOUR SMART HEATER
1. Download Tuya App by scanned the QR code below (ONLY IOS devices). Or
search “Tuya Smart” in the Apple App Store (IOS devices) or Google Play Store
(Android devices).
2. Turn on your smartphone’s Bluetooth ( at the first time use) and ensure
your phone was connected the same WIFI as the heater.
3. Open the Tuya App, tap “Add Device” to search “PTC-SH015” 4. Tap the
device icon and complete pairing with following the on -screen
6
instructions
NOTE:
- Ensure your smartphone’s Bluetooth is turned on ( at the first time use) and your phone was connected the same WIFI as the heater while you pairing the unit.
- Only one device can be paired the unit when using. The WIFI must be reset or the unit must be deleted in the Tuya App if you want to replace the connected device.
- Choose to “Allow” all permissions when using Tuya App for the first time. This app will not record your personal device use.
- This unit has memory function, only for settings of temperature and mode.
The Timer setting or Weekly Program setting will as long as switch ON or Stand
by. If main switch OFF, power cut off, or plug out, it needs to reset. You can
check your settings in the App.
OVERHEAT PROTECTON
1 . A thermal overload protector is built in at the top of the heating panel, if the heater is
obstructed or blocked at front panel and rear ventilation panel by the curtain, drape or cotton sheet etc., the thermal overload protector activates to prevent overheat. 2. When the internal temperature of the heater reaches up to 158 which may cause fire hazard, the heater will be shut off automatically. It can ONLY resume operation when the user resets the unit. To Reset Heater:
- Unplug the heater and wait about 15 minutes until the heater cooling down.
2 . After the heater has cooled down, plug the unit into a 110- 120V
electrical outlet again and follow the operation instructions described in
this manual.
MAINTENANCE AND CLEANING
– Warning : Never use detergent, chemical damage plastic parts. – WARNING : Let the appliance cool down completely before handling or cleaning. – To prevent risk of fire or electrocution inside the appliance. – Clean the outside wall of the appliance by rubbing it gently with soft, damp cloth, either with or without soap. – Regularly clean the air inlet and outlet vents of the fan.
7
SPECIFICATIONS
Model Rating Power
Power Waterproof
PTC-SH019
1500W 120V ~ 60Hz
IPX2
8
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help. -This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your
body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>