GaraDry Door Flood Barrier Threshold Kit 1 1/2″ High Instruction Manual
- June 3, 2024
- GaraDry
Table of Contents
THRESHOLD SEALS FITTING
INSTRUCTIONS MANUAL
Door Flood Barrier Threshold Kit 1 1/2″ High
sales@garadry.com
www.garadry.com
TOOLS REQUIRED
| Tape measure
---|---
| Hacksaw or sharp utility knife
| Pencil or marker pen
| Straightedge or ruler
| Sealant/caulking gun (300ml/10oz or greater cartridge capacity)
GaraDry threshold seals are suitable for use with the following types of
manual and automatic garage doors: up-and-over, sectional, roller-shutter and
side-hinged.
The threshold seal should only be installed by a responsible adult and due
care and attention should be paid when stepping over the threshold seal.
This product is not suitable for use on loose concrete or gravel surfaces.
Unsealed concrete floors that have a dusty or powdery surface must be sealed
with a concrete sealer prior to installation.
The threshold can be installed on epoxy floors, but if the surface is very
smooth it can prevent the adhesive from bonding properly. If your epoxy floor
has a smooth or shiny surface, a low-grit sandpaper can be used to dull the
surface slightly before installation. The same can be done for very smooth
tiles. Remove any dust and debris left behind before proceeding to
installation.
Due to coiling in transport, the threshold seal should be laid flat on a clean
surface so that it returns to its original shape.
The adhesive / sealant should be stored at room temperature prior to
application so it can flow freely from the tube. The recommended ambient
temperature for applying the
adhesive is 5°C to 35°C (40°F to 95°F).
Once fitted allow 24 hours before driving over the threshold.
It is also recommended to test the installation after 24 hours using a bucket
of water or a hosepipe to check for water ingress.
IMPORTANT
Please read through all instructions before beginning installation. Step 1 –
Preparing the Installation Area
Clean the installation area to remove dust, debris, oil, and grease prior to
fitting. If your floor is painted, use a wire brush to remove any loose paint
and provide a sound surface for the adhesive to bond properly. Be sure to
remove any dust or debris left behind after doing so.
Step 2
Measure the overall width of the opening between frame or side tracks. Allow
an additional 40mm (1 ½”) at each end for the threshold seal to be notched
back around the door frame and cut the threshold seal to that required length.
Step 3
With the door closed, position the threshold seal against the back of the door
from inside the garage. Mark where the threshold seal needs to be notched back
around the door frame/tracks so it can sit tight against the back of the
door. Use a hacksaw or sharp utility knife to cut the threshold seal where you
have marked.
Step 4
With the garage door closed, place the threshold seal in position and push it
up against the back of the door to create a tight seal. The garage door should
close onto the front face of the seal (please ensure the garage door shuts
correctly and locks with the seal in position – if it does not, then move the
threshold back slightly and re-check. It is also advisable at this stage if
you have an electrically operated door that the motor continues to operate
normally).
If there is visible daylight, then the threshold seal may need to be cut back
further around the door tracks to ensure a tight seal. Step 5
With the threshold seal in position, mark along the back edge of the seal
inside the garage with a pencil or marker.
Step 6
Open the garage door and mark along the front edge of the seal. Remove the
threshold seal from the floor and mark two parallel lines approx. 10mm (⅓ ”)
inside the existing lines. Then mark an unbroken zigzag line inside the inner
parallel lines. Step 7 – IMPORTANT
Use a clean, dry cloth to remove any dust, debris, oil, and grease from the
bottom of the threshold seal. Sweep the floor thoroughly ensuring that it is
clean and free from dust, debris, oil, and grease.
Step 8
Cut the end off the adhesive tube using a hacksaw or sharp utility knife
Important
The adhesive / sealant should be stored at room temperature prior to
application so it can flow freely from the tube. The recommended ambient
temperature for applying the adhesive is 5°C to 35°C (40°F to 95°F).
Step 9
Use a hacksaw or sharp utility knife to cut the adhesive nozzle approx.
15mm (½”) from the tip before fitting the tube into the sealant gun.
Step 10
Apply the adhesive to the floor in unbroken lines, following the inner
parallel lines marked out in Step 6 (page 4). Apply an unbroken zigzag line of
adhesive between the parallel lines, following the line marked previously.
Step 11
Starting at one end, place the threshold seal in position on top of the
adhesive and press down firmly. Continue along the length of the threshold
seal, pressing down firmly and ensuring good contact in all areas. Take care
to keep the threshold seal positioned correctly within the lines marked
previously. Remove any excess adhesive from the sides with a clean cloth.
Step 12
Apply adhesive around the door frame and ends of the threshold seal to ensure
a watertight fit. Take care to check for any remaining gaps and apply more
adhesive as required.
Step 13 – Optional
(For Sectional or roller garage doors with open side tracks)
For doors with open side tracks, GaraDry foam side blocks should be inserted
into the space between the wall and the track to prevent water ingress.
- Measure the distance between the wall and the garage door track.
- Cut the side block to size using a hacksaw or sharp utility knife.
- Use plenty of adhesive to stick the side block in position on the floor and wall.
- Apply unbroken lines of adhesive around the side block where it meets the wall, door, and track.
- Check for any remaining gaps and apply more adhesive as required.
IMPORTANT
Once installed allow 24 hours before driving over the threshold.It is also
recommended to test theinstallation after 24 hours using a bucket of water or
a hosepipe from outside to check for water ingress.
QUESTIONS?
The GaraDry team is happy to help!
Call: 01704 532 360 (UK)
866-563-2707 (US)
Email: sales@garadry.com
Web: www.garadry.com
Happy with your finished installation?
Let us know!
We would love to know how your finished installation looks, please feel free
to send some photos to: sales@garadry.com
Product Care Guide
| Driving over the threshold seal| When driving across the threshold
seal, ensure this is done at a slow speed. Excess speed can put large amounts
of stress on the seal and cause damage. It is not a speed ramp!
---|---|---
| Heavy weights on the threshold seal| threshold seal Do not overload
the threshold seal with excessive weight. The seals are designed for domestic
vehicles. If you are unsure about which threshold seal will work with your
vehicle, a weight guide is available on our website.
| Stepping over the threshold seal| Due care and attention should be
taken when stepping over the threshold seal to avoid the risk of tripping.
| | Avoid exposing the threshold seal to caustic chemicals, petroleum or
detergents. This can cause discoloration and may cause the adhesive to fail.
| | To clean the threshold seal, simply use a damp cloth. Do not use abrasive
cleaners or detergents.
| | Do not use a pressure washer to clean the threshold seal. This can damage
the seal and adhesive, causing the watertight seal to fail.
GaraDry (HQ)
Units 16-18
17 Summerwood Lane
Halsall Ormskirk
Lancashire, L39 8RG
| GaraDry Australia
Regus – Level 14
380 St Kilda Rd
Melbourne
Victoria, 3004
---|---
GaraDry France
Regus – Lyon Part-Dieu,
Immeuble Danica B
21, Avenue Georges Pompidou
69486 Lyon
CEDEX 03| GaraDry United States
Regus – 100 Hartsfield Center Parkway
Suite 500
Atlanta
Georgia 30354
GaraDry Germany
Regus – Subbelrather Strasse 15a
50823 Köln| GaraDry Italy
Regus – Via Caldera, 21
Easypoint (Building F)
20153 Milano