GEILI MZWX Series Remote Control User Manual
- August 19, 2024
- GEILI
Table of Contents
User Manual
Remote Control
Model: MZWX-F1-1, MZWX-F1-2, MZWX-F1-3, MZWX-F1-4, MZWX-F1-5, MZWX-F1-6,
MZWX-F1-7, MZWX-F1-8, MZWX-F1-9, MZWX-F1-11, MZWX-F1-12, MZWX-F1-13,
MZWX-F1-14, MZWX-F1-15, MZWX-F1-16
Thanks for choosing this wireless switch control which can be widely used for
household appliances like monitor, printer, speakers and more. It even can be
used for industrial equipment or security equipment.
Please read the user manual carefully before use
How to process code pairing and code clearing?
This wireless switch controller supports 3 control modes.
Mode 1: ON button for turning ON, OFF button for turning OFF (recommended):
a. Press receiver’s code button 3 times, pilot lamp is on in green color;
b. Press ON button of remote controller, green pilot lamp is flickering 3
times. Then press OFF button of remote controller, green pilot lamp is again
flickering 3 times. Done. Mode 2: 1 remote controller button can control both
ON and OFF:
a. Press receiver’s code button 2 times, pilot lamp is on in green color;
b. Press any key of remote controller, green pilot lamp is flickering 3 times.
Done. Mode 3: Press and hold the button, controlled product on, release your
hand, controlled product off:
a. Press receiver’s code button 1 time, pilot lamp is on in green color;
b. Press any key of remote controller, green pilot lamp is flickering 3 times.
Done.
How to process code clearing?
Press receiver’s code button 8 times, pilot lamp flickering 7 times means code
clearing done.
Remind: if found failed code pairing or clearing, please re-perform the steps
mentioned above.
Safety Notes:
- This is not a toy, please keep away from children;
- Wiring as per marked port, wrong wiring is prohibited;
- Make sure the load is suitable for the products specification;
- Electric shock caution during wiring.
Specification:
| Voltage | DC 6V |
|---|---|
| Modulation: | OOK |
| Operating Frequency: | 433.92MHz |
| Battery type in remote controller: | CR2016*2 |
| Operating temperature: | -10℃~+50°℃ |
| Control distance | Outdoor (without barrier): 70 m (230 ft), |
Indoor (1 wall is permitted): 30 m (98ft)
Material (remote controller)| ABS + Zinc Alloy + Silica gel
Material (receiver)| ABS
FCC warning statements:
This equipment has been tested and found to comply with the limits for a Class
B digital device,pursuant to part 15 of the FCC Rules.These limits are
designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference
that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>