TheTagFactory Nano-LT Asset Tag User Manual
- July 29, 2024
- TheTagFactory
Table of Contents
Nano-LT Asset Tag – User Manual
Safety Recommendations
This is a commercial use product and should not be installed where children
will be present.
Failure to follow these safety instructions could result in fire, electric
shock, or other injury or damage.
Do not disassemble, dismantle, open, crush puncture, or shred the product.
If the product housing/envelope is weakened, cracked, or broken, stop using it
immediately.
Do not attempt to short-circuit the battery or make contact with a
conductive/metal object.
Do not expose the product to heat, fire or flame.
Do not fully immerse product in water or other liquid.
The battery should be replaced by a trained professional using appropriate
tools. Danger of explosion if battery is incorrectly replaced.
ONLY UL approved SR1116SW batteries can be used in this product. Any other
battery could result in fire, electric shock, or damage.
Dispose of all batteries in accordance with applications laws and regulations.
WARNING
Do not ingest battery. Chemical Burn Hazard.
This product contains a coin cell battery. If the battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death. Keep new
and used batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children. If you
think a battery might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
Failure to follow these instructions can result in personal injury or property damage, and the manufacturer will have no liability whatsoever for any such injury or damage arising from or in connection with any failure to follow these or other instructions provided to the end user.
Description
The asset tag is a long life, cost-effective proximity tag with multiple
mounting options designed for commercial environments. The asset tag is
intended to be attached an asset by the methods outlined in this user manual
only.
Asset Tag Features and Sensors:
– 2.4 GHz radio
– SR1116SW battery
– Double sided adhesive attachment.
The product has the following exterior dimensions: 45.28 mm x 30 mm
Characteristics
Listed below are the main performance characteristics:
| Features | Description |
|---|---|
| Use | Indoor Only |
| Usage | Continuous |
| Power | UL approved SR1116SW Battery Only |
| Internal supply | 1.55V DC |
| Relative humidity environment | Less than 95% non-condensing humidity |
| Frequency band | 2.4GHz ISM Band |
| Operating temperature | From -10°C to + 60°C noncondensing |
| Storage temperature | From 0°C to +35°C noncondensing |
| Mechanical dimensions | 23.3 mm x 8.6 mm |
The indicated storage temperature range is intended to maximize the battery life and avoid unexpected discharge during storage. The product can be exposed to an increased temperature range than the indicated storage temperature range (as long as it stays within operating temperature range), but exposure to more extreme temperatures during storage may reduce battery life.
Installing the Tag
The product is designed to have a small footprint and be attatched to commercial equipment using the provided 3M adhesive.
• Adhesive
Before adhering the device to the asset surface, clean it using an 50/50
mixture of isopropyl alcohol and water can remove dust and oils on the surface
to prep for good adhesion.
Ideal application temperature range for adhesive application is 70°F to 100°F
(21°C to 38°C) but as low as 32°F (0°C) is acceptable. The adhesive will bond
to a broad range of high surface energy substrates including metals, glass,
plastics and easier to bond paints.
- Using included Tag double-sided adhesive, remove one side of the protective film and secure it to the back of the Tag
- Remove the other of side of the protective film and apply securely to the asset
Note: Do not install over 2 meters from the ground.
• Activation
- Pull the battery tab to turn on Tag
- Using asset tracking software,
a. Scan Tag QR code or manually enter Tag ID
b. Enter asset information
c. Confirm successful pairing by pressing SUBMIT
Regulatory Notices
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment.
Operation of this device is restricted to indoor use only.
FCC
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Notice of Compliance
CAN ICES-3(B) / NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
—This device may not cause interference.
—This device must accept any interference, including interference that may
cause undesired operation of the device.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
WARNING
Do not ingest battery. Chemical Burn Hazard.
This product contains a coin cell battery. lf the battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death. Keep new
and used batteries away from children. lf the battery compartment does not
close securely, stop using the product and keep it away from children. If you
think a battery might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>